Radio Shack Cordless Telephone ET 543 User Guide

43-1043.fm Page 1 Tuesday, August 17, 1999 10:36 AM  
Cat. No. 43-1043  
OWNER’S MANUAL  
Please read before using this equipment.  
ET-543  
LCD Display 25-Channel  
Cordless Telephone  
 
43-1043.fm Page 3 Tuesday, August 17, 1999 10:36 AM  
Important: Cordless phones such as  
this one require AC power to operate.  
When the AC power is off, you cannot  
dial out or receive incoming calls using  
your ET-543. For this reason, the ET-  
543 cordless phone should not be your  
only telephone. To be safe, you should  
also have a phone that does not require  
AC power to operate (not a cordless  
phone)soyoucanstillmakeandreceive  
calls if there is an AC power failure.  
Warning: To prevent fire or shock  
hazard, do not expose this product  
to rain or moisture.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVIC-  
ING TO QUALIFIED PERSONNEL.  
This telephone has been tested and  
found to comply with all applicable UL  
and FCC standards.  
This symbol is intended to alert you  
to the presence of uninsulated dan-  
gerous voltage within the product’s  
enclosure that might be of sufficient  
magnitude to constitute a risk of  
electric shock. Do not open the  
product’s case.  
Your ET-543 operates on standard ra-  
dio frequencies, as allocated by the  
FCC. Therefore, it is possible for other  
radio units operating on similar fre-  
quencies, within a certain area, to in-  
advertently intercept your conversa-  
tions and/or cause interference on  
your cordless telephone. This lack of  
privacy can occur with any cordless  
telephone.  
This symbol is intended to inform  
you that important operating and  
maintenance instructions are in-  
cluded in the literature accompany-  
ing this product.  
!
For your records, we urge you to  
record the serial number of your phone  
in the space below. The serial number  
is located on the bottom panel of the  
base.  
Serial Number ______________  
3
 
43-1043.fm Page 4 Tuesday, August 17, 1999 10:36 AM  
READ THIS BEFORE  
INSTALLATION  
FCC STATEMENT  
This telephone complies with Part 68  
of FCC Rules. You must, upon re-  
quest, provide the FCC registration  
number and the REN to your phone  
company. These numbers are located  
on the bottom of your phone’s base.  
We have designed your telephone to  
conform to federal regulations, and  
you can connect it to most telephone  
lines. However, each device that you  
connect to the phone line draws power  
from the phone line. We refer to this  
power draw as the device’s ringer  
equivalence number, or REN. The  
REN is shown on the bottom of your  
phone’s base.  
Note: You must not connect your  
phone to any of the following:  
• Coin-operated systems  
• Party-line systems  
If you are using more than one phone  
or other device on the line, add up all  
the RENs. If the total is more than five,  
your phone might not ring. In rural ar-  
eas, a total REN of three might impair  
ringer operation. If ringer operation is  
impaired, remove a device from the  
line.  
• Most electronic key phone sys-  
tems  
4
 
43-1043.fm Page 5 Tuesday, August 17, 1999 10:36 AM  
CONTENTS  
Installation ............................................................................................................ 6  
Selecting a Location ........................................................................................ 6  
Installing the Phone ........................................................................................ 6  
Preparation ........................................................................................................... 7  
Connecting the Battery ................................................................................... 7  
Charging the Battery ....................................................................................... 7  
Setting the Dialing Mode ................................................................................. 8  
Operation .............................................................................................................. 9  
Making/Answering a Call ................................................................................ 9  
Using the Handset at the Base ................................................................. 9  
Using the Handset Away from the Base ................................................... 9  
Reducing Interference ................................................................................... 10  
Using Redial .................................................................................................. 10  
Using FLASH/DEL ........................................................................................ 10  
Using Tone Services on a Pulse Line ........................................................... 11  
Using Page ................................................................................................... 11  
Memory Dialing ............................................................................................. 11  
Storing a Number in Memory .................................................................. 12  
Entering a Pause in a Memory Number ................................................. 13  
Dialing a Stored Number ........................................................................ 13  
Chain Dialing .......................................................................................... 14  
Testing Stored Emergency Numbers ...................................................... 14  
Troubleshooting ................................................................................................ 15  
Care and Maintenance ...................................................................................... 17  
Replacing the Battery .................................................................................... 18  
The FCC Wants You to Know ....................................................................... 18  
Lightning ....................................................................................................... 19  
5
 
43-1043.fm Page 6 Tuesday, August 17, 1999 10:36 AM  
INSTALLATION  
SELECTING A LOCATION  
INSTALLING THE PHONE  
Select a location for the telephone that  
meets these requirements:  
Follow these steps to install the base  
on a desk, shelf, or table.  
• Near an AC outlet  
• Near a telephone line jack  
• Out of the way of normal activities  
• Away from electrical machinery,  
electrical appliances, and metal  
walls or filing cabinets  
• Away from wireless intercoms,  
alarms, and room monitors  
1. Plug one end of the supplied mod-  
ular cord into the phone jack on  
the back of the base.  
The base’s location affects the phone’s  
range. If you have a choice of several  
locations, try each one to see which  
provides the best performance.  
2. Plug the modular cord’s other end  
into a modular phone line jack.  
3. Insert the supplied AC adapter’s  
barrel plug into the DC 12V jack on  
the back of the base.  
If the phone line jack is not a modular  
jack, you must update the wiring your-  
self, using jacks and adapters avail-  
able at your local RadioShack store.  
Or, you can let the phone company up-  
date the wiring for you.  
4. Plug the adapter into a standard  
AC outlet.  
For the best reception, fully extend the  
base’s antenna and place it in a verti-  
cal position.  
Notes:  
• The phone company will charge  
you for the installation of the nec-  
essary jacks.  
Caution:  
You must use a 120V AC/  
12V DC adapter that delivers at least  
200 milliamps. Its center tip must be  
positive, and its plug must correctly fit  
the phone’s DC 12V jack. The supplied  
adapter meets these requirements.  
Using an adapter that does not meet  
these requirements could damage the  
phone or the adapter.  
• The USOC number of the jack to  
be installed is RJ11C.  
6
 
43-1043.fm Page 7 Tuesday, August 17, 1999 10:36 AM  
PREPARATION  
CONNECTING THE  
BATTERY  
CHARGING THE  
BATTERY  
Before you use your phone for the first  
time, you must connect and charge the  
battery.  
Before you charge the battery, set  
POWER to OFF. Then place the hand-  
set on the cradle so the CHARGE/  
TALK indicator lights and let the bat-  
tery charge for about 15 hours.  
Slide off the battery compartment cov-  
er on the back of the handset. Connect  
the battery’s plug to the pins inside the  
compartment.  
When  
on the handset lights, re-  
charge the battery. To avoid damage  
to the battery, always recharge the  
handset before battery power grows  
Replace the cover, then follow the in-  
structions under “Charging the Bat-  
tery.”  
too weak to light  
.
Notes:  
• You can set POWER to ON while  
the battery charges.  
• If the CHARGE/TALK indicator  
does not light when you place the  
handset on the cradle, be sure the  
battery is connected to the pins  
inside the battery compartment  
and the AC adapter is securely  
connected to the base. Also,  
check the charging contacts on  
7
 
43-1043.fm Page 8 Tuesday, August 17, 1999 10:36 AM  
the handset and base. If the con-  
tacts are dirty or tarnished, gently  
clean them with a pencil eraser.  
SETTING THE DIALING  
MODE  
Set TONE/PULSE on the back of the  
base for the type of service you have.  
• About once a month, fully dis-  
charge the battery by keeping the  
handset off the cradle until  
flashes, then return the  
handset to the cradle and fully  
recharge the battery. If you do not  
fully discharge and recharge the  
battery periodically, it loses its  
ability to fully recharge.  
If you are not sure which type you  
have, do this test.  
1. Set TONE/PULSE to TONE.  
2. Lift the handset and listen for a  
dial tone.  
• The first time you use your phone  
after charging a new battery, the  
handset might not work and might  
sound an error tone when you  
press TALK. This might also occur  
when you recharge a battery that  
has been completely discharged.  
If this happens, be sure the hand-  
set is turned on, then return the  
handset to the cradle for 5 sec-  
onds. This resets the security  
access code.  
3. Press any number other than 0.  
If the dial tone stops, you have  
touch-tone service. Leave TONE/  
PULSE set to TONE.  
If the dial tone continues, you  
have pulse service. Set TONE/  
PULSE to PULSE.  
8
 
43-1043.fm Page 9 Tuesday, August 17, 1999 10:36 AM  
OPERATION  
Your ET-543’s LCD display shows  
telephone numbers as you dial them or  
when you recall them from memory. It  
shows the current channel number and  
lets you know when battery power is  
growing weak or the phone is out of  
range of the base. The display also  
shows indicators when you press  
FLASH/DEL or PAUSE.  
To make a call, lift the handset from  
the base and press TALK so the key-  
pad and the CHARGE/TALK indicator  
on the base light.  
Note: CH  
and the currently used  
MAKING/ANSWERING  
A CALL  
channel number appear on the display.  
This number might change when you  
return the handset to the base.  
You can use your cordless telephone  
in two ways: at the base or away from  
the base.  
To disconnect a call, replace the hand-  
set on the base.  
Using the Handset  
at the Base  
Using the Handset  
Away from the Base  
You can use the handset at the base  
like a regular corded telephone. Just  
set POWER to ON and place the hand-  
set in the cradle.  
To make or answer a call, set POWER  
to ON and press TALK. The keypad  
and CHARGE/TALK indicator light.  
To disconnect a call, press TALK so  
the keypad light and the CHARGE/  
TALK indicator turn off.  
Notes:  
CHand the currently used channel  
number appear on the display.  
To conserve battery power, you  
can turn off the handset’s power  
when you are not making or  
answering a call.  
To answer a call, just lift the handset  
from the base.  
9
 
43-1043.fm Page 10 Tuesday, August 17, 1999 10:36 AM  
• You can make or answer a call on  
a phone on the same line as the  
cordless phone, even if the hand-  
set is away from the base.  
RANGE appears when the dis-  
tance from the handset to the  
base is out of the phone’s range.  
• The keypad lights on the handset  
turn off if no button is pressed for  
more than 13 seconds.  
The redial memory holds up to 80 dig-  
its in the tone or pulse mode. The redi-  
al memory also holds pause entries  
(see “Entering a Pause” under “Memo-  
ry Dialing”).  
REDUCING  
INTERFERENCE  
RE-  
Note: We recommend you not use  
DIAL  
CH  
To reduce interference, press  
to  
to dial numbers that include a  
tone (*) entry (see “Using Tone Servic-  
es on a Pulse Line”).  
switch to the next channel (25 chan-  
nels in all) until you receive the best re-  
ception. CH and the channel number  
appear on the display.  
USING FLASH/DEL  
FLASH/DEL  
Use  
on the handset to per-  
form the switchhook operation for spe-  
cial services, such as call waiting.  
USING REDIAL  
To quickly redial the last number you  
dialed, simply lift the handset from the  
TALK  
base and press  
CHARGE/TALK indicator lights, and  
REDIAL  
again so the  
For example, if you have call waiting,  
FLASH/DEL  
press  
call without disconnecting the current  
FLASH/  
to take an incoming  
then press  
. The redialed num-  
ber appears on the display.  
call. FLASH appears. Press  
DEL  
again to return to the first call.  
10  
 
43-1043.fm Page 11 Tuesday, August 17, 1999 10:36 AM  
Notes:  
USING PAGE  
• If you do not have special phone  
PAGE  
The  
feature allows someone at  
FLASH/DEL  
services, pressing  
the base to page you at the handset. It  
also helps you find the handset if you  
misplaced it.  
might disconnect the current call.  
• The redial memory does not store  
FLASH/DEL  
a
entry or any digits  
FLASH/  
entered after you press  
DEL  
With the handset’s power on, the  
handset beeps four sets of two beeps  
.
PAGE  
when you press  
on the base.  
TALK  
The  
key on the handset flashes,  
and the channel number and INT ap-  
pear on the display.  
USING TONE SERVICES  
ON A PULSE LINE  
Some special services, such as bank  
by phone, require tone signals. If you  
have pulse service, you can still use  
these special tone services by follow-  
ing these steps.  
TONE/PULSE  
1. Set  
on the base to  
PULSE  
.
2. Dial the service’s main number.  
Note: The handset will not beep during  
a call.  
3. When the service answers, press  
*
on the keypad. Aappears on the  
display. Then dial the additional  
numbers. The phone sends these  
numbers as tone signals.  
MEMORY DIALING  
You can store up to 30 phone numbers  
for quick and easy dialing. Each stored  
number can be up to 16 digits long.  
4. When you complete the call, place  
the handset on the cradle or press  
TALK  
to disconnect the call. The  
phone automatically resets to the  
pulse mode.  
Notes:  
TONE/PULSE  
PULSE  
is set to  
• If  
RE-  
and you want to use tone dialing  
for a memory number, you must  
store the tone entry along with the  
number.  
Note: We recommend you not use  
DIAL  
to dial numbers that include a  
*
tone ( ) entry.  
11  
 
43-1043.fm Page 12 Tuesday, August 17, 1999 10:36 AM  
To keep your accounts secure, we  
recommend you do NOT store  
your personal access code for  
services such as bank-by-phone  
in a memory location.  
• The phone does not dial the  
number at this point.  
• If you enter a wrong digit, press  
FLASH/DEL to delete the last  
entered digit.  
• If you enter more than 16 digits,  
the phone buzzes and the dis-  
play turns off. To dial a number  
with more than 16 digits, see  
“Chain Dialing.”  
Storing a Number in Memory  
1. With the handset’s power on,  
press MEMORY. The keypad lights  
and MEMappears on the display.  
3. Press MEMORY again.  
4. Enter the two-digit memory loca-  
tion number (01, 02 ..... 30) where  
you want to store the number. The  
index number appears, and a long  
beep sounds. The phone number  
is now stored in the memory.  
5. Pull out the memory index card at  
the bottom of the base. Write the  
person’s or company’s name and  
index number on the sheet in pen-  
cil (in case you want to change it  
later).  
Note: While you are storing a  
number in memory, if you do not  
press any button on the keypad  
within about 9 seconds, the key-  
pad light turns off and a buzz  
sounds. You must press MEMORY  
again so the keypad lights before  
you can store the telephone num-  
ber.  
2. Enter the phone number you want  
to store. The number appears on  
the display.  
6. Repeat Steps 1-5 to store other  
telephone numbers.  
Notes:  
12  
 
43-1043.fm Page 13 Tuesday, August 17, 1999 10:36 AM  
Notes:  
Dialing a Stored Number  
• If you receive a call while you are  
storing a number in memory,  
There are three ways to dial a stored  
number.  
TALK  
press  
to answer the call.  
After the call, begin again at Step  
1 to store the number.  
Method 1  
1. Lift the handset from the cradle  
To change a phone number stored  
in memory, simply store a new  
phone number in that location.  
TALK  
and press  
so the keypad  
TALK  
and  
key light.  
2. When you hear a dial tone, press  
MEMORY  
To clear a memory location so no  
number is stored there, press  
, then press the number  
buttons for the correct memory  
location. The stored number  
appears on the display, and the  
phone dials the stored number.  
MEMORY  
twice, then press the  
location number. A long beep  
sounds. The phone number is  
now cleared from the memory.  
If a buzz sounds, you did not suc-  
cessfully clear the memory loca-  
tion. Try the process again.  
Entering a Pause  
in a Memory Number  
In some telephone systems, you must  
dial an access code (9, for example)  
and wait for a second dial tone before  
you can dial an outside number. If your  
phone is connected to one of these  
systems, you might want to enter a  
pause at the appropriate point when  
you store a phone number in memory.  
Method 2  
1. Lift the handset from the cradle  
TALK  
and press  
so the keypad  
TALK  
and  
key light.  
At the appropriate place in the number,  
PAUSE  
press  
to enter a 2-second  
pause. Pappears. For a longer pause,  
PAUSE  
press  
again.  
PAUSE  
Note: Each  
entry uses one dig-  
it of memory.  
13  
 
43-1043.fm Page 14 Tuesday, August 17, 1999 10:36 AM  
2. Press SCROLL s/t to search for  
the desired stored number. The  
selected number appears on the  
display.  
2. Wait for the service to answer.  
If you use pulse dialing to  
Note:  
dial the service, be sure you have  
stored a * (tone) entry in the mem-  
ory location you use to send the  
additional information.  
3. Press MEMORY and the numbers  
for the memory location where the  
additional information is stored.  
The numbers appear.  
3. Press ENTER. The phone dials the  
4. To disconnect the call, press TALK  
stored number.  
so the TALK key does not light.  
Method 3  
Testing Stored  
Emergency Numbers  
1. With POWER set to ON and the  
TALK key not lit, press SCROLL s/t  
to search for the desired stored  
number.  
If you store an emergency service’s  
number (police, fire, ambulance) and  
you want to test the stored number,  
make the test call during the late  
evening or early morning to avoid peak  
demand periods. Remain on the line to  
explain the reason for your call.  
2. Press TALK. The phone dials the  
number automatically.  
Chain Dialing  
When storing numbers for special ser-  
vices (such as alternate long distance  
or bank-by-phone), store the service’s  
main phone number in one memory lo-  
cation and numbers for additional in-  
formation in other memory locations.  
To chain dial memory numbers, follow  
these steps.  
1. With the handset’s power on,  
press MEMORY and the memory-  
location number for the service’s  
main number. The numbers  
appear.  
14  
 
43-1043.fm Page 15 Tuesday, August 17, 1999 10:36 AM  
TROUBLESHOOTING  
We do not expect you to have any problems with your telephone, but if you do, the  
following suggestions might help. If you still have problems, check other phones on  
the same line to see if they work properly. If they do and the problem does not seem  
to be with your phone service, take your phone to your local RadioShack store for  
assistance.  
Problem: The handset does not work.  
Solutions:  
• Be sure POWER is set to ON.  
• Move the handset closer to the base.  
• Be sure the phone line cord and AC adapter are correctly and securely con-  
nected.  
• Be sure the battery is connected and charged.  
• Fully extend the base’s antenna vertically.  
• Return the handset to the cradle for 10 seconds, then try again.  
Problem: Volume drops or you hear unusual sounds.  
Solution: Someone has picked up another phone on the same line. Hang up the  
other phone.  
Problem: Call is noisy.  
Solutions:  
• Do not place the base near appliances or large metal objects.  
• Hang up and redial the number.  
• Keep the handset away from interference sources such as computers, remote  
control toys, wireless microphones, wireless alarm systems, wireless intercoms  
and room monitors, fluorescent lights, and electrical appliances. If the interfer-  
ence is severe, turn off the interfering device.  
• Press CH to switch to another channel.  
15  
 
43-1043.fm Page 16 Tuesday, August 17, 1999 10:36 AM  
Problem: The handset’s range decreases.  
Solutions:  
• Fully extend the base’s antenna vertically.  
• Return the handset to the cradle, and recharge the battery.  
• Be sure the antenna is not touching a metal surface.  
Problem: Receiver sound flutters or fades.  
Solutions:  
• Be sure the battery is charged.  
• Fully extend the base’s antenna vertically.  
• Move the handset closer to the base.  
Problem: Can make calls, but telephone does not ring.  
Solution: Telephone company may be using unusual ringing methods. Your tele-  
phone is designed for standard straight line bridged ringing.  
Problem: Can receive calls, but cannot make calls.  
Solutions:  
TONE/PULSE  
• Set  
correctly for the type of service you have (see “Setting the  
Dialing Mode”).  
• Check with the phone company to see if service is out in your area.  
Problem: You cannot answer/make a call and the handset sounds an error tone  
TALK  
when you lift it from the base or press  
.
Solution: The phone might be receiving interference from another RF signal; or, if  
the handset is away from the base during a long period of AC power failure, the  
phone might loss its access protection code. Return the handset to the base for 5  
seconds.  
16  
 
43-1043.fm Page 17 Tuesday, August 17, 1999 10:36 AM  
CARE AND MAINTENANCE  
Your ET-543 25-Channel Cordless Telephone with LCD Display is an example of  
superior design and craftsmanship. The following suggestions will help you care for  
your phones so you can enjoy it for years.  
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids can  
contain minerals that corrode the electronic circuits.  
Handle the phone gently and carefully. Dropping it can damage cir-  
cuit boards and cases and cause the phone to work improperly.  
Use and store the phone only in normal temperature environments.  
Temperature extremes can shorten the life of electronic devices and  
distort or melt plastic parts.  
Keep the phone away from dust and dirt which can cause premature  
wear of parts.  
Wipe the phone with a damp cloth occasionally to keep it looking  
CLEANER  
new. Do not use harsh chemicals, cleaning solvents, or strong deter-  
gents to clean your phone.  
Modifying or tampering with the phone’s internal components can cause a malfunc-  
tion and might invalidate its warranty and void your FCC authorization to operate it.  
If your phone is not performing as it should, take it to your local RadioShack store  
for assistance. If the trouble is affecting the phone lines, the phone company might  
ask you to disconnect your phone until you have resolved the problem.  
17  
 
43-1043.fm Page 18 Tuesday, August 17, 1999 10:36 AM  
Important: Your telephone contains a  
rechargeable nickel cadmium battery.  
At the end of the battery’s useful life, it  
must be recycled or disposed of prop-  
erly. Contact your local, county, or  
state hazardous waste management  
authorities for information on recycling  
or disposal programs in your area.  
Some options that might be available  
are: municipal curb-side collection,  
drop off boxes at retailers, recycling  
collection centers, and mail back pro-  
grams.  
REPLACING THE  
BATTERY  
If you follow the instructions in “Charg-  
ing the Battery,” the supplied battery  
should last for several years. When the  
battery loses its ability to fully charge,  
order a replacement battery through  
your local RadioShack store. Follow  
these steps to replace the battery, then  
charge the new battery according to  
the instructions in “Charging the Bat-  
tery.”  
1. Slide off the battery compartment  
cover and loosen the plastic strap  
securing the battery. Then discon-  
nect the old battery’s plug from  
the pins and remove the battery.  
THE FCC WANTS YOU  
TO KNOW  
In the unlikely event that your phone  
causes problems on the phone line,  
the phone company can temporarily  
discontinue your service. If this hap-  
pens, the phone company attempts to  
notify you in advance. If advance no-  
tice is not practical, the phone compa-  
ny notifies you as soon as possible and  
advises you of your right to file a com-  
plaint with the FCC.  
2. Insert the new battery in the com-  
partment and secure it with the  
plastic strap. Then connect the  
battery’s plug to the pins inside  
the compartment.  
Also, the phone company can make  
changes to its lines, equipment, opera-  
tions, or procedures that could affect  
the operation of the phone. The phone  
company notifies you of these changes  
in advance, so you can take the neces-  
sary steps to prevent interruption of  
your phone service.  
3. Replace the battery compartment  
cover.  
18  
 
43-1043.fm Page 19 Tuesday, August 17, 1999 10:36 AM  
Your phone might cause TV or radio  
interference even when it is operating  
properly. To determine whether your  
phone is causing the interference, turn  
off your phone. If the interference goes  
away, your phone is causing the inter-  
ference. Try to eliminate the interfer-  
ence by:  
LIGHTNING  
Your phone has built-in protection cir-  
cuits to reduce the risk of damage from  
surges in phone line current. These  
protection circuits meet or exceed FCC  
requirements. However, lightning strik-  
ing the phone lines can damage your  
phone.  
• Moving your phone away from the  
receiver  
Lighting damage is not common. Nev-  
ertheless, if you live an area that has  
severe electrical storms, we suggest  
that you unplug your phone during  
storms to reduce the possibility of  
damage.  
• Connecting your phone to an AC  
outlet that is on a different electri-  
cal circuit from the receiver  
• Contacting  
your  
local  
Ra-  
dioShack store for help  
If you cannot eliminate the interfer-  
ence, the FCC requires that you stop  
using your phone.  
19  
 
43-1043.fm Page 20 Tuesday, August 17, 1999 10:36 AM  
RadioShack Limited Warranty  
This telephone product is warranted against manufacturing defects in material and  
workmanship for one (1) year from the date of purchase from RadioShack company  
owned stores and authorized RadioShack franchisees and dealers. Within this period  
bring your RadioShack sales slip as proof-of-purchase date to any RadioShack  
store.  
This warranty does not cover damage or failure caused by or attributable to Acts of  
God, abuse, misuse, improper or abnormal usage, faulty installation, improper mainte-  
nance, lightning or other incidence of excess voltage, or any repairs other than those  
provided by a RadioShack Authorized Service Facility, or transportation costs.  
RadioShack is not responsible or liable for indirect, special, or consequential  
damages arising out of or in connection with the use or performance of the prod-  
uct or other damages with respect to loss of property, loss of revenue or profit, or  
costs of removal, installation or reinstallation.  
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES  
AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION  
OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states do  
not allow the limitation or exclusion of incidental or consequential damages and some  
states do not allow limitation or exclusion of implied warranties; therefore, the aforesaid  
limitation(s) or exclusion(s) may not apply to the purchaser. There will be charges ren-  
dered for repairs to the product made after the expiration of the aforesaid one (1) year  
warranty period.  
This warranty gives you specific legal rights and you may also have other rights which vary from  
state to state.  
We Service What We Sell  
10/95  
RadioShack  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
11A6  
Printed in Hong Kong  
 

Radio Shack Telephone ET 651 User Guide
RCA Stereo System ANT2020X User Guide
RedMax Pole Saw LRT A User Guide
Reebok Fitness Treadmill RBTL796071 User Guide
Ricoh All in One Printer 4506 User Guide
RIDGID Security Camera SeeSnake User Guide
RocketFish Network Card RF MRBTAD User Guide
Rockford Fosgate Car Speaker FRC3204 User Guide
Ryobi Power Screwdriver HP36KF User Guide
Sanus Systems TV Mount VLMF109 B1 User Guide