Radio Shack Answering Machine 43 3803 User Guide

2TQHGUUKQPCN"*KIJ"%CRCEKV["&KIKVCN"#PUYGTKPI"5[UVGO

43-3803

OWNER’S MANUAL — Please read before using this equipment.

For the system’s Caller ID memory dial fea-

ture to operate, you must receive the caller’s

number.

LIGHTNING

%106'065

Answering System Features ............................... 1

Caller ID Features ............................................... 2

Installation ........................................................... 2

Connecting the System ....................................... 2

Installing a Backup Battery .................................. 2

Answering System ............................................... 2

Preparation .......................................................... 2

Turning the System On/Off ............................... 2

Setting Up Your System ................................... 2

Setting the Number of Rings ............................ 3

Using Toll Saver ............................................... 3

System Operation ................................................ 3

Recording the Outgoing Messages ..................... 3

General OGM ................................................... 3

Announce Only OGM ....................................... 3

Setting the VIP Number ................................... 3

Reviewing VIP Numbers .................................. 3

Recording VIP OGM ........................................ 3

VIP Alert Tone .................................................. 3

Setting the System to Answer Calls .................... 4

Using the Announce-Only Feature ................... 4

Memo Recording .............................................. 4

Two Way Recording ......................................... 4

Using Silence ................................................... 4

Screening Calls ................................................ 4

Playing Incoming Messages/ Memos/ 2-Way Con-

versations ............................................................ 4

Playing VIP Messages ..................................... 5

Deleting Voice Messages .................................... 5

Remote Operation ............................................... 5

Remote Operation Security Code .................... 5

Operating the Answering System from a Remote

Location ............................................................ 5

Remote Commands ......................................... 5

Caller ID Operation .............................................. 5

Reviewing Caller ID Records .............................. 6

Using the Master/Secondary Switch ................... 6

Call Back from the Caller ID Memory .................. 6

Receiving Call Waiting Calls ................................ 6

Caller ID Messages ............................................. 6

Deleting Caller ID Records .................................. 7

Troubleshooting ................................................... 7

Your system has built-in protection circuits to

reduce the risk of damage from surges in

telephone line current. These protection cir-

cuits meet or exceed the FCC requirements.

However, lightning striking the telephone

lines can damage your telephone and the

system.

READ THIS BEFORE

INSTALLATION

We have designed your system to conform to

federal regulations and you can connect it to

most phone lines. However, each device that

you connect to the telephone line draws pow-

er from the line. We refer to this power draw

as the system’s ringer equivalence number,

or REN. The REN is shown on the bottom of

your system.

Lightning damage is not common. Neverthe-

less, if you live in an area that has severe

electrical storms, we suggest that you unplug

your telephone and the system when storms

approach to reduce the possibility of damage.

Your RadioShack Digital Telephone Answer-

ing System with 99/99 CID Memory is a com-

bination high-quality fully-digital answering

system and Caller ID. The system prevents

you from missing incoming calls and messag-

es. Fully digital means the system stores all

messages on a computer chip. This gives

you capabilities that tape-based answering

machine do not have. There is no tape mech-

anism to wear out and no tapes to bother

with. Also, you can listen quickly from mes-

sage to message without listening to all of

them.

If you use more than one system or other de-

vice on the line, add up all the RENs. If the

total is more than five (three in rural areas),

your telephone might not ring. If ringer opera-

tion is impaired, remove one of the devices

from the line.

FCC STATEMENT

Your system complies with Part 68 of FCC

Rules. You must, upon request, provide the

FCC registration number and REN to your

telephone company. These numbers are on

the bottom of the system.

The system displays the caller’s telephone

number (and name, if available in your area)

and the current date and time, as provided by

your local phone company to Caller ID ser-

vice subscribers. It saves up to 99 Caller ID

records that you can review and call back.

You must not connect your system to:

• coin-operated systems

• party-line systems

• most electronic key phone systems

ANSWERING SYSTEM

FEATURES

THE FCC WANTS YOU TO

KNOW

Twelve Outgoing Messages — lets you

record twelve outgoing messages of up to

about 30 seconds each: eleven for when you

want callers to leave a message (ten VIP call-

ers and a non-VIP caller), one for when you

want to play an announcement without re-

cording callers’ messages.

Care

In the unlikely event that your system causes

problems on the telephone line, the tele-

phone company can disconnect your service.

The telephone company normally attempts to

notify you in advance. If advance notice is not

practical, the telephone company notifies you

as soon as possible and advises you of your

right to file a complaint with the FCC.

Important Caller ID Information

To use this Caller ID, you must be in an area

where Caller ID service is available, and you

must subscribe to the service.

Where Caller ID is offered, one or more of the

following options are generally available:

Voice Date/Time Stamp — records the day

and time each message was recorded.

Also, the telephone company can make

changes to its lines, equipment, operations,

or procedures that could affect the operation

of this telephone. The telephone company

notifies you of these changes in advance so

you can take the necessary steps to prevent

interruption of your telephone service.

• caller’s number only

• caller’s name only

Two-Way Recording — lets you record both

sides of your phone conversation.

Memo Recording — lets you leave messag-

es for yourself or others.

• caller’s name and number

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

• To change the above settings, press

TIME SET/SKIP to repeat Steps 1 through

8. Press STOP to end setting actions.

stop listening to the outgoing message

before it ends, press STOP.

Turning the System On/Off

To turn on the system, press ANSWER ON/

OFF. The ANSWER ON/OFF indicator lights

and the system beeps once. The system is

set to answer calls.

• If you have recorded your OGM, PLAY

flashes when you press ANNOUNCE.

To avoid losing the day and time settings if

AC power fails, we recommend you install a

backup battery before you set the day and

time (see “Installing a Backup Battery” on

Page 2).

Announce Only OGM

Setting Up Your System

1. Press ANNOUNCE and Fbiý I[b[Yjý E=C

appears.

After you turn on the system, press TIME SET/

SKIP. I[b[YjýBWd]kW][ appears and then ;D=

;IF. Follow these steps to set up your system

Setting the Number of Rings

2. Hold down ANNOUNCE, speak into the

microphone. Release the button when

you finish your message. The system

automatically plays back your recorded

message.

Set 2/4/7/TS located on the right side of the

system to 2, 4, 7 to set how long the system

waits before it answers a call (2 rings, 4 rings,

7 rings).

1. Press 9VOLUME8. ;D= or ;IF flashes

to indicate which language you selected.

After you select the language, press

REVIEW 7#to confirm the language.

Note:

Using Toll Saver

2. After you select the language, 7H;7 F?D

:7OUMAý appears. Press 9VOLUME8

to select the area code and press

REVIEW7 to move the cursor to the

next digit. After you select the area code,

press REVIEW7# to confirm the area

code.

• The maximum length for an outgoing

message is 30 seconds.

To help you avoid unnecessary long distance

charges, you can set 2/4/7/TS to TS (Toll Sav-

er). Once you select TS, if there are new

messages, the system answers on the sec-

ond ring. If there are no new messages, the

system answers on the fourth ring. This fea-

ture gives you time to hang up after the third

ring when you are checking messages from a

long-distance location.

• To hear the announce-only OGM at any

time, press ANNOUNCE twice. To stop lis-

tening to the outgoing message before it

ends, press STOP.

3. Press 9VOLUME8# to select the PIN

code (3 digit remote operation security

code) and press 6REVIEW7 to move

the cursor. After you select the pin code,

press REVIEW7 to confirm the pin.

• If you have not recorded an announce-

only OGM and the switch is set to ANNC

ONLY, the system answers telephone line

after 2 rings and plays a prerecorded

announce-only OGM that says “No one

is available to take your call,” then

sounds 5 beeps. Enter the remote oper-

ation security code within 10 seconds,

then enter 8# to start recording your

announce-only OGM. To stop recording,

enter 5#. Your OGM automatically plays

back once.

5;56'/"12'4#6+10

Note: The preset pin code is 000.

RECORDING THE OUTGOING

MESSAGES

4. The cursor is at :7OUMA. Press

9VOLUME8 to enter the day of the

week. Press REVIEW7 to confirm the

day of the week.

General OGM

The system has a prerecorded outgoing mes-

sage that says “Hello, please leave a mes-

sage after the tone.” Use this message or

record your own.

5. Press 9VOLUME8 to select the hour,

then press REVIEW 7 to confirm the

hour.

• The announce-only OGM does not affect

your original OGM that tells callers to

leave a message. Each OGM can be

recorded, played back, or deleted inde-

pendently.

6. Press 9VOLUME8 to select the

minute, then press REVIEW7 to confirm

the minute.

1. Press ANNOUNCE and Fbiý I[b[Yjý E=C

appears.

2. Hold down PLAY, speak into the micro-

phone. Release the button when you fin-

ish your message. The system

automatically plays back your recorded

message.

Setting the VIP Number

7. Press 9VOLUME8 to select the

month, then press REVIEW7 to confirm

the month.

Your system automatically saves an incom-

ing VIP message into a specified location.

You can review these VIP caller’s message

by pressing the VIP button. After you set a

phone number as a VIP number, and the in-

coming call matches the VIP number, the

system stores the voice message into the

specified VIP mailbox. To set the VIP num-

ber:

8. Press 9VOLUME8 to select the date,

then press REVIEW 7 to confirm the

date.

Notes:

• The maximum length for an outgoing

message is 30 seconds. When it

reaches the maximum outgoing mes-

sage length, the system sounds a tone.

Notes:

• Press 6REVIEW7 to move the cursor

when setting the date and time.

1. Press 6 REVIEW 7 until the desired

• If you record your own message and

subsequently decide to use the prere-

corded message, press ANNOUNCE and

then press PLAY to play the general

OGM, then press DELETE during play-

back to erase the recorded message.

Caller ID memory location displays.

• The month, day and time can be updated

by the first incoming call with Caller ID

information.

2. Press VIP, then press VIP Mailbox 1–10

for the desired VIP location. The VIP

mailbox flashes to indicate you have

stored a phone number.

• After the day and time are set, they are

updated by the first incoming call, the

system announces the time and day

when you press TIME CHECK/REPEAT.

• To hear the general OGM at any time,

press ANNOUNCE and then PLAY. To

When there is an incoming call,

9Wbb[hý?: ap-

Notes:

• When the system is set for announce-

Reviewing VIP Numbers

pears when the system is on. The outgoing

message plays after the system answers,

then the system beeps and begins recording.

The caller can leave a message of up to 1 or

5 minutes in length, depending on the setting

of 1/5/ANNC ONLY. After the call (when the

caller hangs up, or there is silence for more

than seven seconds, or the recording maxi-

mum message length), the system hangs up

and resets to answer the next call. The New

Call indicator flashes to indicate the system

recorded a new incoming message.

To review the VIP number you specified,

make sure the system is set to answer calls.

Press VIP, then press 6REVIEW7 to re-

view the VIP mailbox numbers one by one. If

no VIP is set in the mailbox, L?FýNNýdejýI[j ap-

pears. You can delete the number stored in

the VIP mailbox. When reviewing the VIP

number, press DELETE.

only, you cannot set it to record calls

using the remote commands.

• You can still use remote commands to

perform all operations.

• The system always answers on the sec-

ond ring except when the memory is full.

Recording VIP OGM

Memo Recording

The system has ten VIP mailboxes. You can

record a 30-second individual message in

each VIP box.

Follow these steps to record a memo up to 1

minute.

Note:

• The system supports a maximum of 92

incoming messages and outgoing mes-

sages.

1. Hold down 2 WAY/MEMO. After the beep,

speak clearly into the microphone from

about ten inches in front of the system.

1. Press ANNOUNCE and Fbiý I[b[Yjý E=C

appears.

• If the system’s memory reaches its max-

imum capacity while a caller is leaving a

message, the system stops recording,

beeps and then hangs up. If the system

receives a call when its memory is full, it

answers after ten rings and plays “No

one is available to take your call”, waits

for any remote operation commands,

then hangs up. The system cannot

record additional messages until you

delete at least some of the old ones

(See “Deleting Voice Messages” on

Page 5).

2. Hold down the VIP 1–10 and speak

clearly into the microphone. Release VIP

1–10 when you finish your message.

The system automatically plays back

your recorded message.

2. Release 2 WAY/MEMO when you finish

your message.

Two Way Recording

Important: Every state has different regula-

tions governing the recording of conversa-

tions over the telephone. Be sure to check

your local, state and federal laws before us-

ing this product to record any telephone con-

versation in order to determine that your use

is in compliance with such laws or guidelines.

Note: After you finish recording and press

ANNOUNCE, If an VIP mailbox has a VIP

OGM recorded, its indicator flashes.

VIP Alert Tone

The system lets you store up to ten phone

numbers in its VIP call list. Whenever some-

one calls from one of those ten numbers, if

you subscribe to Caller ID, the system will

sound an alert tone (single beep) in between

incoming phone rings to indicate that a VIP

call is coming in. This alert tone continues

until the call is answered. The system sounds

an alert tone (double beep) every 15 seconds

to remind the user that some VIP messages

in VIP mailboxes have not been reviewed.

You can record both sides of a conversation

on any phone connected to the same phone

line as the system.

• If you want to record an OGM, memo or

two-way phone conversation when its

memory is full, the system announces

“Memory is full”.

At any time during a phone conversation,

press 2 WAY/MEMO to start recording. (ýMWo

H[YehZ_d] appears. Press 2 WAY/MEMO once

to stop recording the conversation.

• Many local phone companies use calling

party control (CPC) to signal that the

caller has hung up. Your system can rec-

ognize a CPC signal and release the

line. If the system records phone com-

pany messages or dial tones, your local

phone company probably does not use

CPC.

Note: The message can be as long as re-

maining memory allows, but eight seconds of

silence terminates recording.

To disable the VIP alert feature of incoming

call and new message, hold down VIP for 3

seconds and the display shows the current

setting of VIP alert. If L?Fý7B;HJ ED appears,

press 6REVIEW7 to change to L?Fý7B;HJ

E<<. Press STOP to exit. The system auto-

matically exits after 15 seconds without any

key being pressed.

Using Silence

Using the Announce-Only Feature

To mute the speaker while reviewing Caller

ID information, press SILENCE, the SILENCE

indicator lights. Press SILENCE again to re-

sume listening.

Your system’s announce-only feature lets

you play a message for the caller then auto-

matically hang up without letting the caller

leave a message.

Note: You must press SILENCE before you

review the Caller ID messages in order to

use the silence feature.

SETTING THE SYSTEM TO

ANSWER CALLS

To select announce-only, set 1/5/ANNC ONLY

to ANNC ONLY. When the system receives a

call, it plays the announce-only message and

displays the Caller ID. After the announce-

ment, the system sounds 5 beeps, and stays

on line for 10 seconds so you can enter the

remote operation security if necessary.

Set 1/5/ANNC ONLY to 1 or 5 to select 1

minute or 5 minutes as the maximum length

of incoming messages. To set the system to

answer calls, press ANSWER ON/OFF. The

ANSWER ON/OFF indicator turns on.

Screening Calls

To screen calls, let the system answer and

you can listen to the caller’s message

through the answering system’s speaker. If

you decide to answer the call, pick up any

phone connected to the same phone line as

the system. The system stops recording and

resets to answer the next call.

To set the system so it does not answer calls,

press ANSWER ON/OFF so the ANSWER ON/

OFF indicator turns off.

If the system receives no code within ten

seconds, the system hangs up and resets to

answer the next call. To turn off announce-

only, set 1/5/ANNC ONLY to either 1 or 5.

Notes:

• If you pick up the phone just as the sys-

ter your remote operation security code and

do any of the following:

Playing VIP Messages

After the VIP alert tone sounds during an in-

coming VIP call, the system also sounds

beep tones to indicate there are new VIP

messages. The VIP mailbox button flashes

after the system records one or more new

VIP incoming messages in those VIP mail-

boxes.

tem answers, the system might not stop

playing the OGM. If this happens, press

STOP to stop the OGM or the switchhook

on your phone to stop the OGM.

• set the system to answer calls

• listen to your messages

• record a new OGM

• When 9VOLUME8 is set to the mini-

mum level, the incoming caller’s mes-

sages cannot be heard. Be sure

9VOLUME8 is set to the appropriate

level for screening calls.

• delete an individual message

Follow these steps to play VIP messages.

Remote Operation Security Code

1. Press the blinking VIP 1–10. The system

plays each new VIP message and dis-

plays the Caller ID as you press each

blinking VIP button. After playing each

message, the system announces the day

and time the message was recorded.

To use your system from a remote telephone,

you must first enter a 3-digit remote operation

security code (see “Setting Up Your System”

on Page 3). Enter the security code within

about 8 seconds after the system answers

and sounds 1 beep. Within 10 more seconds,

enter a remote command.

If you do not want to take the call, let the sys-

tem finish recording the caller’s message.

PLAYING INCOMING

MESSAGES/ MEMOS/ 2-WAY

CONVERSATIONS

2. After the messages play, the VIP indica-

tor lights. The system automatically

saves the messages and resets to

answer calls.

Operating the Answering System

from a Remote Location

PLAY flashes after the system has recorded

one or more new incoming messages, re-

corded memos, or a two-way conversation.

3. The system announces “Mail Box X”

before playing VIP messages during

remote operation.

1. Dial your phone number.

To play the messages:

2. After the outgoing message plays and

the system beeps, enter your remote

operation security code.

1. Press PLAY once, D[m0NN and JejWb0NN

appear on the voice messages counter

for 2 seconds.

DELETING VOICE MESSAGES

Notes:

To delete a specific voice message , press

DELETE during message playback. :[býLe_Y[

Ci]5 flashes on the display. Press DELETE to

confirm deletion.

2. The system plays back all new mes-

sages.

• If you do not enter each digit within 8

seconds, the system hangs up.

3. After all new messages finish playing

back, press PLAY again. All messages

will be played back, one after the other,

beginning with the first message.

• The system answers after 10 rings

and beeps 5 times even if it is set to

answer off.

Follow these steps to delete all voice mes-

sages.

1. Press PLAY.

3. Enter a remote command.

After playing each message, the system an-

nounces the day and time the message was

recorded. After you play the voice messages,

the system automatically saves the messag-

es and resets to answer calls. The PLAY indi-

cator lights.

2. Press DELETE. :[býLe_Y[ýCi]5 flashes.

4. When you finish, press 5# to end remote

access or simply hang up.

3. Press REVIEW7until :[bý 7bbý Le_Y[5

flashes.

Remote Commands

4. Press DELETE. The PLAY indicator turns

off.

Use the keys on a touch-tone phone or pock-

et tone dialer to operate the answering sys-

tem when you are away from your home or

office. Enter your selection within 10 sec-

onds, or the system automatically hangs up

and resets to answer the next call.

Notes:

• If the system sounds a double beep after

you press PLAY, there are no messages.

• If you decide not to delete the messages,

do not press DELETE and wait until the

system resets to answer calls.

• To repeat the current message, press

TIME CHECK/REPEAT.

• If you press DELETE to confirm deletion

during :[bý 7bbý Le_Y[, message that have

been played are deleted. Messages that

have not been played are retained and

the PLAY indicator still flashes.

Press

• To review previous message, hold down

TIME CHECK/REPEAT for 1 second.

Play new messages

Play all messages

• To skip forward to the next message,

press TIME SET/SKIP.

Delete current message

Repeat previous message

Stop and exit

• You can delete a voice message and

CID record at the same time (see “Delet-

ing Caller ID Records” on Page 7).

• To stop playback of any message at any

time, press STOP.

Skip a message

• During playback of any incoming mes-

sage, the display shows the attached

Caller ID at the same time.

Turn the system On/Off

REMOTE OPERATION

Record an OGM, press 5# when you

finish

While you are away from your home or office,

you can use a touch-tone phone or a pulse

(rotary) phone with a pocket tone dialer to en-

Record a Memo, press 5# when you

finish

• If you connect another type of CID mod-

ule that has Call Waiting (other than this

system) to the same phone line as your

system, the Call Waiting signal might be

garbled or not received.

REVIEWING CALLER ID

RECORDS

Press

1+1~0 Play new VIP messages 1–10

Each time you receive a call, the system

stores a Caller ID record that you can review

later, even during a call. A Caller ID record

includes:

2+1~0 Play all VIP messages 1–10

Notes:

CALL BACK FROM THE

CALLER ID MEMORY

• If you enter the correct remote operation

security code several times, but the sys-

tem does not accept it, the code might

have reset because of low battery

power. Try entering the default security

code 000. If this works, replace the sys-

tem’s backup battery and set the secu-

rity code as desired when you return to

the system’s location.

• call number

Press CALL BACK to dial the number from

the displayed record. :_Wb_d]$$$$$$ appears and

the system dials the number.

• time and date of the call

• callers’ telephone number (if available)

• caller’s name (if available)

Depending on your phone system’s require-

ments, you might need to press

6REVIEW7 after CALL BACK to change

the dial format.

• voice message (if the calling party

leaves a message)

• If you do not have CPC service and

hang up while the system is playing back

messages, the system might not recog-

nize that you hung up. If someone calls

while the system continues playing mes-

sages, the caller hears a busy signal.

We recommend that you stop and exit

remote commands until the system

beeps once before you hang up.

If the caller’s phone number has the same

area code as your preset area code, repeat-

edly press 6REVIEW7 to cycle through the

formats below.

To review the call records:

In the answer-ready mode, press REVIEW6

to review most recent calls. Press REVIEW7

to view the oldest calls. After you view the

most recent calls or oldest calls in memory, #

;dZýe\ýB_ijý#ýappears. If there is a voice mes-

sage attached to the call record, the system

automatically announces the message.

• Local phone number (7-digit number)

• 1 + local phone number (1+7-digit

number if your system requires you to

dial 1 before a 7-digit number)

Notes:

%#..'4"+&"

• area code + local phone number (10-

digit number [area code plus 7-digit

number])

12'4#6+10

• The NEW CALL indicator flashes until all

the new Caller ID records are reviewed.

If no button is pressed within 15 sec-

onds, the system returns to answer-

ready mode.

If you subscribe to Caller ID service from

your phone company, the phone company

sends information about the call, as well as

the time and date between the first and sec-

ond rings of every call you receive.

• 1 + area code + local phone number

(1 + 10-digit number [if your local

phone system requires you to dial 1

before a long- distance number]).

• If the data in memory is reviewed for the

first time, D;M appears during your

review.

The system displays this information and

stores up to 99 numbers only or name and

number call records in its Caller ID memory,

then replaces the oldest call record with each

new one.

• If the caller’s phone number has a dif-

ferent area code from your preset

area

code,

repeatedly

press

USING THE MASTER/

SECONDARY SWITCH

6REVIEW7 to choose a 10-digit

number or 1+10-digit number. After

selecting the format, press CALL

BACK again to dial out.

During an incoming call, D;M appears. If the

caller’s name has more than 16 characters,

only the first 16 characters appear. The NEW

CALL indicator flashes until all calls are re-

viewed.

The system’s M/S (master/secondary) switch

lets you easily connect up to four system

modules to the same phone line, so you can

receive Caller ID and Call Waiting informa-

tion at more than one phone on that line.

Simply set M/S on the back of one system to

M, and set M/S to S on all (up to three) other

systems. Set one system to answer on; set

the others to answer off.

Notes:

• If you press CALL BACK before picking

up the phone’s handset, F_Yakfý F^ed[

appears.

If the Caller ID information received dupli-

cates another call in memory, the system up-

dates the time/date and HFJ and the number

of times the call was repeated appears. If no

button is pressed within 30 seconds, the sys-

tem returns to answer-ready mode, and dis-

plays the total call counter, new call counter,

current time and date.

• If you do not pick up the handset within

10 seconds, the current CID memory

reappears and you must press CALL

BACK again.

Notes:

• If you connect only one system to a

phone line, set its M/S switch to M. If M/S

on more than one or none of the sys-

tems is set to M, incoming calls might be

disconnected.

RECEIVING CALL WAITING

CALLS

Note: If there is no voice message attached

to a repeat number, the latest call appears

once during CID review. For example, if you

receive a call from the same number 10

times, the CID displays the number once and

HFJý'& appears.

When you are on the phone and you hear the

Call Waiting indication, the display shows

who is calling. To talk with the person, press

FLASH on your phone. To return to your orig-

inal call, press FLASH again.

• You can also connect other caller ID

modules that do not have the Call Wait-

ing function to the same phone line as

your system as long as the total number

of Caller ID modules connected to the

line does not exceed four.

Note: Contact your local phone company to

subscribe to Caller ID with Call Waiting ser-

vices.

6417$.'5*116+0)

Display

English/

Spanish

Description

We do not expect you to have any problems

with your system, but if you do, try these sug-

gestions.

The call was forwarded from

a number set to forward a call

if the line is busy.

<ehmWhZý8kio

EYkfWZeý

7Z[bWdj[

CALLER ID MESSAGES

Problem

Suggestion

Display

The VIP alert feature is on.

The incoming

message is

incomplete.

Be sure the memory is not

full.

L?Fý7b[hjýEd

7b[hjWýL?FýEd

English/

Spanish

Description

Alerts you during reviewing

VIP calls that the mailbox has

no VIP number set.

The number of new calls and

total number of incoming

calls.

L?FýdejýI[j

L?Fýdeý7`kijWZe

D[mýJejWb

Dk[leýJejWb

The incoming

message is

unclear.

^{Be sure}9VOLUME8 is

set to the desired sound

level.

Appears when you press

STOP after you delete mes-

sages or Caller ID records.

Call information is stored in

Caller ID memory location

#01.

MW_j_d]

;dý;if[hW

ç&'

The system

does not

Be sure the system is set to

answer calls.

answer after

two, four, or

seven rings.

Appears when the caller has

blocked Caller ID information

from being sent.

Fh_lWj[

Fh_lWZe

DELETING CALLER ID

RECORDS

The system

does not

respond to the

remote opera-

tion security

code.

Make sure the phone you

use to dial the system is a

touch-tone phone, or use a

pocket-tone dialer.

Appears when the caller is

not within a Caller ID service

area. No caller information

appears.

KdWlW_bWXb[

<k[hWýZ[ýPedW

Follow these steps to delete an individual

Caller ID record.

Re-enter your remote opera-

tion security code, pressing

each number for 2 seconds.

1. Press 6REVIEW7 to recall the record.

The voice message does not

have Caller ID message

information.

9?:ýdejý

WjjWY^[Z

9?:ýDeý7dWZ_h

2. Press DELETE. :[bý9?:ýH[YehZ5ýflashes.

Make sure the remote opera-

tion security code you

3. Press DELETE again to delete the

Appears if there was an error

during the transmission of the

Caller ID information.

;hheh

record.

entered is correct, or try

entering the default code of

000. The remote operation

security code might have

reset to the default code due

to a power failure or a weak

backup battery.

Follow these steps to delete all Caller ID

records.

No call information is stored

in the Caller ID.

Deý9Wbbi

DeýBbWcWZW

1. Press 6REVIEW7.

Appears after the system

dials a number when you

press CALLBACK.

F_YakfýF^ed[

B[lWdjWhýJ;B

2. Press DELETE. :[bý9?:ýH[YehZ5 flashes.

3. Press REVIEW7until :[bý7bbý9?:5 flashes.

4. Press DELETE. Deý9Wbbi appears.

The display is

blank.

The backup battery is weak.

Replace the battery (see

“Installing a Backup Battery”

on Page 2).

Prompts you to set the area

code, remote security opera-

tion PIN, date and day.

7H;7ýF?Dý

:7OUMA

7H;7ýF?DýI[c#

WdW

Make sure AC power is prop-

erly connected (see “Con-

necting the System” on

Page 2).

Follow these steps to delete a CID and voice

message.

Appears when the system or

CID is inactive and a mes-

sage is waiting (if you sub-

scribe to your phone

company’s message waiting

service).

1. Press 6REVIEW7 to recall the CID

The system dis- Make sure the AC power is

record and voice message.

plays and

properly connected. If AC

power fails, the system can

receive Caller ID records but

cannot operate using backup

battery power.

receives Caller

ID records but

does not oper-

ate.

2. Press DELETE. :[býLe_Y[ýCI=5 flashes.

Appears when there is an

incoming call when you are

on the phone.

9WbbýMW_j_d]ý

BbWc$[dý;if[hW

3. Press REVIEW7until :[b 9?:+Le_Y[5

flashes.

CARE

Appears when the Caller ID

memory is full or the system

reaches its maximum mes-

sage counter.

C[cehoý_iý<kbb

C[ceh_WýBb[dW

4. Press DELETE to delete the CID record

and voice message.

Keep the system dry; if it gets wet, wipe it dry

immediately. Use and store the system only

in normal temperature environments. Handle

the system carefully; do not drop it. Keep the

system away from dust and dirt, and wipe it

with a damp cloth occasionally to keep it

looking new.

Notes:

Appears when you have

reached the end of your call

records.

;dZýe\ýB_ij

<_dýZ[ýBWýB_ijW

• If you decide not to delete the records,

do not press DELETE and wait until the

system resets to answer calls.

Appears when you review a

Caller ID record from some-

one who has called more

than one time from the same

number.

HFJ

• If you press DELETE to confirm deletion

during :[b 7bb 9?:5, all Caller ID records

will be deleted, including records that

have not been reviewed.

Modifying or tampering with the system’s in-

ternal components can cause a malfunction

and might invalidate its warranty and void

your FCC authorization to operate it. If your

system is not performing as it should, take it

to your local RadioShack store for assis-

tance. If the trouble is affecting the telephone

lines, the phone company can ask you to dis-

The call was forwarded from

a number set to forward all

calls.

9Wbbý<ehmWhZ

BbWcýI_]k_[dj[

connect your system until you have resolved

the problem.

Limited One-Year Warranty

This product is warranted by RadioShack against manufacturing defects in material and

workmanship under normal use for one (1) year from the date of purchase from Ra-

dioShack company-owned stores and authorized RadioShack franchisees and dealers.

EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES

AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO

THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN.

EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-

SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-

SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR

INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT

OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY

DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROP-

ERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts or the exclu-

sion or limitation of incidental or consequential damages, so the above limitations or ex-

clusions may not apply to you.

In the event of a product defect during the warranty period, take the product and the Ra-

dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack

will, at its option, unless otherwise provided by law: (a) correct the defect by product re-

pair without charge for parts and labor; (b) replace the product with one of the same or

similar design; or (c) refund the purchase price. All replaced parts and products, and

products on which a refund is made, become the property of RadioShack. New or re-

conditioned parts and products may be used in the performance of warranty service.

Repaired or replaced parts and products are warranted for the remainder of the original

warranty period. You will be charged for repair or replacement of the product made after

the expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of

God, abuse, accident, misuse, improper or abnormal usage, failure to follow instruc-

tions, improper installation or maintenance, alteration, lightning or other incidence of ex-

cess voltage or current; (b) any repairs other than those provided by a RadioShack

Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic

damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal,

installation, set-up service adjustment or reinstallation.

This warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

12/99

Radica Games Games G73007 User Guide
Radio Shack Clock 63 247 User Guide
Radio Shack Portable CD Player CTR 98 User Guide
Raymarine GPS Receiver ST6002 User Guide
Ryobi Router RT401W User Guide
Ryobi Sander DS11008 User Guide
Samsung Bluetooth Headset B1914B1914 User Guide
Samsung Graphics Tablet SM T2105 User Guide
Samsung Washer J1053 V S User Guide
Schwinn Motor Scooters Mobility Aid 50CA06PK User Guide