RCA TV Mount MAF40BK User Guide

Safety precautions  
Attaching wall mount plate  
Drywall Installation  
Follow these precautions to ensure safe installation and  
mounting of your flat panel TV.  
1. Use a stud finder to locate a wood stud where you want  
to install the mount.  
NOTE: It is required that the wall mount plate be  
LCD TV Wall Mount  
1. Be sure you have purchased the correct wall mount  
attached to wall studs.  
for your TV. Recheck the size and weight constraints.  
2. Locate center of stud.  
with Double Swing Arm Extension  
Installation Manual  
2. Gather all necessary tools before you begin installation.  
You will need a #3 bit Phillips screwdriver, electric  
drill, drill bit (included), level (integrated level on  
product), stud finder, and hammer (for brick and  
concrete installations).  
3. Place the wall mount plate against the wall, with the  
cord management channel towards the bottom. Level it  
using the bubble guide. Mark the locations on the wall  
where the mount is to be installed.  
Fits TVs 13"- 27"  
4. Drill holes at each marked location using the enclosed  
3. It is essential for the wall mount plate to be attached  
wood drill bit.  
Maximum Load Capacity – 40 lbs. (18 kg)  
to wall studs. (Use a stud finder.)  
5. Secure the wall mount plate to the wall, using one  
4. Use the included hardware for mounting purposes.  
This hardware has been provided to ensure a safe and  
secure mount.  
drywall screw, but do not completely tighten it yet.  
6. Using the integrated bubble level, carefully adjust the  
wall mount plate until it is level.  
5. Hire a licensed electrician to relocate an electrical  
7. Insert the remaining screws and tighten all three  
outlet, if needed.  
screws completely.  
6. Be sure to purchase wires long enough to connect  
the TV to the audio and video components in your  
installation.  
MAF40BK  
Concrete/Brick Installation  
Thank you for choosing a Universal Flat Panel TV Wall  
Mount from RCA. This mount can be used for all major  
brands of 13" - 27" flat panel TVs, 40 lbs (18 kg) or under.  
This wall mount features a 0-15-degree tilt, 180-degree  
pan and swivel, and double swing arm extension for easy  
viewing. Before attempting to mount your television set,  
please remove all parts from this package and read the  
installation instructions carefully.  
7. We recommend you hire a professional installer,  
if you have any concerns about installing the TV  
wall mount yourself.  
1. Place the wall mount plate against the wall with the  
cord management channel towards the bottom.  
2. Using the integrated bubble level, mark off the position  
of the holes that will be used for securing the mount.  
3. Place the wall mount plate aside.  
Keep your sales receipt to obtain warranty parts and  
service and for proof of purchase. Attach it here and record  
the model number. This number is located on the product.  
4. Using an electric drill and a 5/16" (8mm) masonry bit,  
drill holes in the marked locations.  
5. Remove any excess dust from the holes.  
6. Insert a concrete anchor into each hole. If necessary,  
use a hammer to lightly tap each anchor into place so  
they are flush with the wall.  
WARNING: Use of this mount with a TV weighing  
over 40 lbs. or with a screen larger than 27" could cause  
the mount to fail causing property damage and/or  
personal injury.  
Model No. __________________________________________  
Purchase Date: ______________________________________  
Dealer/Address/Phone ______________________________  
7. Once both anchors are in place, place the wall mount  
plate back into position. Using the integrated bubble  
level, carefully adjust the wall mount plate until it is  
level.  
Limited Lifetime Warranty  
Audiovox Electronics Corporation (the “Company”) warrants to you the  
original retail purchaser of this product that should it, under normal use  
and conditions, be proven defective in material or workmanship during  
its lifetime while you own it, such defect(s) will be repaired or replaced (at  
the Company’s option) without charge for parts and repair labor.  
8. Attach the wall mount plate, using the drywall screws  
provided.  
9. Make sure all screws are tightened and secure.  
Product diagram  
To obtain repair or replacement within the terms of this Warranty, the  
product is to be delivered with proof of warranty coverage (e.g. dated bill  
of sale), specification of defect(s), transportation prepaid, to the Company  
at the address shown below. Do not return this product to the Retailer.  
Attaching the TV mount plate  
TV Mount Plate  
This Warranty does not cover product purchased, serviced or used  
outside the United States or Canada.  
1. Unplug your flat panel TV before starting this step of  
Adjustment Knob  
the installation.  
This Warranty is not transferable and does not extend to costs incurred for  
installation, removal or reinstallation of the product. This Warranty does  
not apply if in the Company’s opinion, the product has been damaged  
through alteration, improper installation, mishandling, misuse, neglect,  
or accident.  
Double Swing Arm Extension  
IMPORTANT: NEVER lay the TV face down as this  
may cause damage to the viewing surface.  
Retainer Clip  
2. Before attaching the TV mount plate to the TV,  
determine which hardware to use. Examine the back of  
your TV. If the back is flat, use the M4x12mm bolts. If  
your TV has a recessed back, use the longer M4x30mm  
bolts and 1/2" spacers.  
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS  
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT  
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S  
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER  
FOR THE PRODUCT.  
3. After you have determined which bolts to use, attach  
This Warranty is in lieu of all other express warranties or liabilities. ANY  
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY  
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE  
SHALLBELIMITEDTODURATIONOFTHISWARRANTY.INNOCASE  
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR  
INCIDENTALDAMAGESWHATSOEVER.Nopersonorrepresentativeis  
authorized to assume for the Company any liability other than expressed  
herein in connection with the sale of this product.  
the TV mount plate to the back of your TV.  
NOTE: Be careful not to over-tighten the bolts.  
Integrated Bubble Level  
Wall Mount Plate  
Security Bolt Position  
Some states/provinces do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential  
damage so the above limitations or exclusions may not apply to you. This  
Warranty gives you specific legal rights and you may also have other  
rights which vary from state/province to state/province.  
Cord Management Channel  
Attaching the TV mount plate  
to the wall mount plate  
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,  
Hauppauge, New York 11788  
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,  
Unit 3, Door 16, Mississauga, Ontario L5T 3A5  
1. To complete the installation, slide the TV mount plate  
with your TV attached into the wall mount plate.  
Trademark(s) Registered, Marques Deposee, Marcas Registradas.  
All other brands and product names are trademarks or registered  
trademarks of their respective owners.  
2. The retainer clip on the top of the wall mount plate  
Specifications  
should click, indicating that the mount is secure.  
3. To remove the TV, push in on the clip and slide the TV  
© 2008 Audiovox Accessories Corporation  
111 Congressional Blvd., Suite 350  
Carmel, IN 46032  
Model:  
MAF40BK  
Two-piece, low-profile design  
mount plate up.  
4. For additional security and stability, insert the security  
Description:  
RCA Universal LCD TV Wall  
Mount with Swing Arm Extension  
bolt into the hole located at the base of the unit.  
MAF40BK_US_IB_00  
5. Tighten, using the Allen Wrench provided.  
Color:  
Black  
TV Size Range:  
Max. Load:  
Min. Profile:  
13" – 27"  
Preparing to install  
40 lbs. (18kg)  
2.6" (6.6 cm)  
Before beginning the installation process, verify that you  
have all the necessary tools on hand. The following tools  
are required for proper installation:  
Operation and adjustment  
Max. Extension: 9.7" (24.6 cm)  
Tilt:  
+/- 0-15°  
180°  
Your RCA Flat Panel TV Wall Mount features an adjustable  
15-degree tilt and 180-degree pan and swivel action for  
easy viewing.  
Swivel:  
Tools  
VESA Compliant: 75/100  
Integrated Bubble Level  
Cord Management System  
#3 bit Phillips screwdriver  
Stud finder  
To adjust the tilt:  
Electric drill  
1. Locate the adjustment knob directly behind the TV  
Drill bit (included)  
mounting point.  
5/16" (8mm) masonry drill bit for concrete/  
brick installation  
2. Loosen the knob by turning it counter-clockwise.  
3. Adjust the tilt to the desired level and re-tighten the  
Level (integrated level on product)  
Allen Wrench (included)  
knob to lock the adjustment in place.  
Hammer (for concrete installations)  
To adjust the swivel:  
1. Simply move the extension arm into the desired  
position.  
Package Contents  
2. If the joint is too tight or too loose, adjust the tightness  
Make sure all the hardware has been included with  
your mount.  
of the joint.  
3. Locate the knob closest to the wall.  
(1) Drill Bit  
4. Turn the knob counter-clockwise to loosen and  
(3) 1-7/8" Drywall Screws  
(3) Concrete Anchors  
(2) Allen Wrenches  
(4) M4x12mm Bolts  
(4) M4x30mm Bolts  
(4) 1/2" Spacers  
clockwise to tighten.  
(1) Security Bolt  
(1) Phillips-Head Driver  
 

Q See Security Camera QSDS4936D User Guide
Quantum Audio Stereo Amplifier QCA4400 User Guide
Quasar Air Conditioner HQ 2081TH User Guide
Reebok Fitness Treadmill RBTL10500 User Guide
Roberts Radio Portable Radio R9921 User Guide
Robic Thermostat SC 577 User Guide
RocketFish Video Gaming Accessories RG GWII012 User Guide
Samsung DVD VCR Combo V6700 User Guide
Sanyo Digital Camera VCC MCH5600 User Guide
Sennheiser Headphones HD 218 User Guide