RCA Camcorder EZ1100 User Guide

user manual  
EZ1100 series  
It is important to read this user manual prior to using your new product for the first time.  
 
Important battery precautions  
Any battery may present a risk of fire, explosion, or chemical burn if abused. Do not try to charge a  
battery that is not intended to be recharged, do not incinerate, and do not puncture.  
Non-rechargeable batteries, such as alkaline batteries, may leak if left in your product for a long  
period of time. Remove the batteries from the product if you are not going to use it for a month or  
more.  
If your product uses more than one battery, do not mix types and make sure they are inserted  
correctly. Mixing types or inserting incorrectly may cause them to leak.  
Discard any leaky or deformed battery immediately. They may cause skin burns or other personal  
injury.  
Please help to protect the environment by recycling or disposing of batteries according to federal,  
state, and local regulations.  
WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat  
such as sunshine, fire or the like.  
Ecology  
Help protect the environment - we recommend that you dispose of used batteries by putting them  
into specially designed receptacles.  
Precautions for the unit  
Do not use the unit immediately after transportation from a cold place to a warm place;  
condensation problems may result.  
Do not store the unit near fire, places with high temperature or in direct sunlight. Exposure to  
direct sunlight or extreme heat (such as inside a parked car) may cause damage or malfunction.  
Clean the unit with a soft cloth or a damp chamois leather. Never use solvents.  
The unit must only be opened by qualified personnel.  
2
 
FCC Information  
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  
radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by Audiovox could void the user’s authority to operate the  
equipment.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
this device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
Manufacturer/Responsible Party  
Audiovox Accessories Corporation  
111 Congressional Blvd., Suite 350  
Carmel, IN 46032  
1-317-810-4880 ( No technical /product support is available via this number. This phone number is for  
regulatory matters only.)  
RCA  
EZ1100  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
3
 
Contents  
Important safety instructions  
IMPORTANT SAFETY INSTRUCTIONS.............................................................................................. 1  
Important battery precautions ........................................................................................................ 2  
Ecology...................................................................................................................................................... 2  
Precautions for the unit ...................................................................................................................... 2  
FCC Information................................................................................. 3  
Contents ............................................................................................. 4  
End user license agreement  
End user license tagreement ............................................................................................................ 6  
Getting started  
1. Content of the box........................................................................................................................... 12  
2. Battery Installation........................................................................................................................... 12  
3. Inserting SD memory card............................................................................................................ 13  
4. Turning on the camcorder ........................................................................................................... 13  
5. Resetting the camcorder ............................................................................................................... 14  
6. Setting date and time..................................................................................................................... 14  
General controls  
General controls .................................................................................................................................... 15  
Operation modes .................................................................................................................................. 16  
Recording videos  
Recording quality.................................................................................................................................. 17  
Quality settings...................................................................................................................................... 17  
Recording videos................................................................................................................................... 18  
Taking photos  
To take photos........................................................................................................................................ 19  
Playback mode  
Playing back recordings...................................................................................................................... 20  
Deleting  
To delete one recording ..................................................................................................................... 22  
To delete all recordings....................................................................................................................... 22  
Menu settings  
Using the camcorder menu............................................................................................................... 23  
Menu options and settings ............................................................................................................... 23  
4
 
Connecting to external devices  
Viewing videos on TV .......................................................................................................................... 24  
Recording videos to VHS tape or DVD ......................................................................................... 24  
Managing videos on your computer  
Computer system requirements...................................................................................................... 25  
Connecting to a PC............................................................................................................................... 25  
About RCA Memory Manager .......................................................................................................... 26  
Viewing videos on PC.......................................................................................................................... 26  
Using camcorder as Web Camera in PC  
Additional information  
Tips and troubleshooting................................................................................................................... 27  
Visiting RCA website ............................................................................................................................ 28  
Technical specifications ...................................................................................................................... 29  
Warranty information  
12 Month Limited Warranty .............................................................................................................. 30  
5
 
End user license agreement  
This is a copy of the EULA that you need to agree to in order to use this product.  
End user license tagreement  
IMPORTANT: THIS WINDOW CONTAINS TWO SEPARATE END USER LICENSE AGREEMENTS (“EULA”): 1)  
THE AUDIOVOX CORPORATION EULA AND 2) THE ARCSOFT CORPORATION EULA. BY INSTALLING THE  
FOLLOWING PROGRAM OR CLICKING ON THE ACEPTANCE BUTTON OF THE PROGRAM, COPYING OR  
OTHERWISE USING THE PROGRAM, YOU ACKNOWLEDGE AND AGREE THAT YOU HAVE READ EACH EULA,  
UNDERSTAND EACH EULA, AND AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF EACH EULA.  
1. AUDIOVOX CORPORATION EULA  
AUDIOVOX CORPORATION  
END USER LICENSE AGREEMENT  
IMPORTANT: READ CAREFULLY BEFORE DOWNLOADING OR INSTALLING THIS SOFTWARE!  
THIS END USER LICENSE AGREEMENT (THIS “EULA”) IS A LEGAL AGREEMENT BETWEEN YOU AND  
AUDIOVOX CORPORATION AND, AS APPLICABLE, ANY AUDIOVOX SUBSIDIARY, AS DEFINED BELOW  
(COLLECTIVELY “AUDIOVOX”), FOR THE RCA BRANDED PORTABLE DIGITAL AUDIO/VIDEO DEVICE  
APPLICATION/DRIVER SOFTWARE PROGRAM WHICH MAY INCLUDE ASSOCIATED SOFTWARE  
COMPONENTS, SOFTWARE LICENSED BY AUDIOVOX FROM THIRD PARTIES (“LICENSORS”) AND  
ASSOCIATED DOCUMENTATION, IF ANY (COLLECTIVELY, THE “PROGRAM”). THIS EULA CONTAINS  
IMPORTANT LEGAL LIMITATIONS, RESTRICTIONS AND DISCLAIMERS, AND ALSO SPECIFIES THE DURATION  
OF YOUR LICENSE.  
BY INSTALLING THE PROGRAM OR CLICKING ON THE ACCEPTANCE BUTTON OF THE PROGRAM, COPYING  
OR OTHERWISE USING THE PROGRAM, YOU ACKNOWLEDGE AND AGREE THAT YOU HAVE READ THIS EULA,  
UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. THIS PROGRAM IS  
PROTECTED BY COPYRIGHT LAWS AND INTERNATIONAL COPYRIGHT TREATIES, AS WELL AS OTHER  
INTELLECTUAL PROPERTY LAWS AND TREATIES. YOU MAY USE THE PROGRAM ONLY IN ACCORDANCE  
WITH THIS EULA, AND ANY SUCH USE IS HEREBY UNDERSTOOD TO BE CONDITIONAL UPON YOUR SPECIFIC  
AGREEMENT TO THE UNMODIFIED TERMS SET FORTH HEREIN. IF YOU DO NOT AGREE WITH ALL OF THE  
TERMS OF THIS EULA, CLICK ON THE REJECTION BUTTON AND/OR DO NOT INSTALL THE PROGRAM AND/  
OR DO NOT USE THE PROGRAM.  
1. LICENSE  
(a) Under this EULA, you are granted a non-exclusive, non-sublicenseable, non-assignable and non-  
transferable (except as expressly set forth below) license (i) to use and install the Program on a single  
workstation, and (ii) to make one (1) copy of the Program into any machine-readable form for backup of  
the Program, provided the copy contains all of the original Program's proprietary notices.  
(b) You may transfer the Program and license to another party only as a part of the RCA branded Portable  
Digital Audio/Video Device (“A/V Device”), and only if the other party agrees to accept the terms and  
conditions of this EULA. If you transfer the Program, you must at the same time either transfer all copies  
to the same party or destroy any copies not transferred.  
(c) The terms of this EULA will govern any software upgrades or updates provided by AUDIOVOX that  
replace and/or supplement the original Program, unless such upgrade or update is accompanied by  
separate license terms and conditions in which case the terms of that separate license will govern. You  
acknowledge and agree that AUDIOVOX may automatically download upgrades or updates to the  
Program software to your computer in order to update, enhance, and/or further develop the Program.  
6
 
2. LICENSE RESTRICTIONS  
(a) Except for the licenses expressly granted to you in this EULA, no other licenses or rights are granted or  
implied.  
(b) You may not (i) make the Program available over a network where it could be used by multiple  
computers at the same time; (ii) modify, translate, reverse engineer, decompile, disassemble (except to the  
extent that this restriction is expressly prohibited by law), or create derivative works based upon the  
Program; (iii) copy the Program, except as expressly permitted herein; (iv) remove or alter any copyright  
notices on all copies of the Program; or (v) rent, lease or lend the Program. You agree that you shall only  
use the Program in a manner that complies with all applicable laws in the jurisdictions in which you use  
the Program, including, but not limited to, applicable restrictions concerning copyright and other  
intellectual property rights.  
(c) The Program may contain pre-release code that does not perform at the level of a final code release. In  
such case, the Program may not operate properly. Updated versions of the Program may be downloaded  
(d) AUDIOVOX is not obligated to provide support services for the Program.  
(e) The Program is provided with “RESTRICTED RIGHTS. Use, duplication, or disclosure by the U.S.  
Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or FAR  
52.227-19, or in FAR 52.227-14 Alt. III, as applicable.  
3. TERM AND TERMINATION  
(a) Your license is effective on the date you accept this EULA and remains in effect until this EULA is  
terminated by either party.  
(b) You may terminate this EULA and the associated license, without any notice or delay, by destroying or  
permanently erasing the Program and all copies thereof.  
(c) If you fail to comply with any of the terms of this EULA, in whole or part, your license will automatically  
terminate without notice from AUDIOVOX.  
(d) Upon termination of this EULA and your associated license, you shall cease all use of the Program and  
destroy or permanently erase the Program and all full or partial copies thereof.  
4. WARRANTY DISCLAIMER  
THE PROGRAM IS PROVIDED “AS ISWITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,  
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE, TITLE OR NON-INFRINGEMENT. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU (AND  
NOT AUDIOVOX, ITS SUPPLIERS, OR ITS DEALERS) ASSUME THE ENTIRE COST FOR ALL NECESSARY REPAIR  
OR CORRECTION.  
This exclusion of warranty may not be allowed under some applicable laws. As a result, the above  
exclusion may not apply to you, and you may have other rights depending on the law that applies to you.  
5. OWNERSHIP RIGHTS  
All title and intellectual property rights, including but not limited to copyrights, in and to the Program and  
any copies thereof are owned by AUDIOVOX, its Licensors or its suppliers. All title and intellectual property  
rights in and to the content which may be accessed through use of the Program is the property of the  
respective content owner and may be protected by applicable copyright or other intellectual property  
laws and treaties. This license grants you no rights to use such content. All rights not expressly granted are  
reserved by AUDIOVOX or its Licensors.  
7
 
6. LIMITATION OF LIABILITY  
(a) TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL AUDIOVOX, OR ITS  
DEALERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES  
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS  
INTERRUPTION, CORRUPTION OF FILES, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY  
LOSS) REGARDLESS OF CAUSE OR FORM OF ACTION, INCLUDING CONTRACT, TORT, OR NEGLIGENCE,  
ARISING OUT OF YOUR USE OF OR INABILITY TO USE THE PROGRAM, EVEN IF AUDIOVOX HAS BEEN  
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND JURISDICTIONS DO NOT  
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE  
ABOVE LIMITATION MAY NOT APPLY TO YOU.  
(b) YOU ASSUME RESPONSIBILITY FOR THE SELECTION OF THE APPROPRIATE PROGRAM TO ACHIEVE YOUR  
INTENDED RESULTS, AND FOR THE INSTALLATION, USE, AND RESULTS OBTAINED.  
7. THIRD PARTY SOFTWARE  
ANY THIRD PARTY SOFTWARE THAT MAY BE PROVIDED WITH THE PROGRAM IS INCLUDED FOR USE AT  
YOUR OPTION. IF YOU CHOOSE TO USE SUCH THIRD PARTY SOFTWARE, THEN SUCH USE SHALL BE  
GOVERNED BY SUCH THIRD PARTY'S LICENSE AGREEMENT, AN ELECTRONIC COPY OF WHICH WILL BE  
INSTALLED IN THE APPROPRIATE FOLDER ON YOUR COMPUTER UPON INSTALLATION OF THE SOFTWARE.  
AUDIOVOX IS NOT RESPONSIBLE FOR ANY THIRD PARTY’S SOFTWARE AND SHALL HAVE NO LIABILITY FOR  
YOUR USE OF THIRD PARTY SOFTWARE.  
8. GOVERNING LAW  
If you acquired this A/V Device in the United States, this EULA shall be governed and construed in  
accordance with the laws of the State of Indiana, U.S.A. without regard to its conflict of laws principles. If  
you acquired this A/V Device outside the United States or the European Union, then local law may apply.  
9. GENERAL TERMS  
This EULA can only be modified by a written agreement signed by you and AUDIOVOX, and changes from  
the terms and conditions of this EULA made in any other manner will be of no effect. If any portion of this  
EULA shall be held invalid, illegal, or unenforceable, the validity, legality, and enforceability of the  
remainder of the Agreement shall not in any way be affected or impaired thereby. This EULA is the  
complete and exclusive statement of the agreement between you and AUDIOVOX, which supersedes all  
proposals or prior agreements, oral or written, and all other communications between you and AUDIOVOX,  
relating to the subject matter of this hereof. AUDIOVOX’S Licensors shall be considered third party  
beneficiaries of this Agreement and shall have the right to enforce the terms herein.  
“AUDIOVOX SUBSIDIARY” shall mean any person, corporation, or other organization, domestic or foreign,  
including but not limited to subsidiaries, that is directly or indirectly controlled by Audiovox Corporation  
including, but not limited to, Audiovox Consumer Electronics, Inc. and Audiovox Electronics Corporation.  
For purposes of this definition only, the term “control” means the possession of the power to direct or  
cause the direction of the management and policies of an entity, whether by ownership of voting stock or  
partnership interest, by contract, or otherwise, including direct or indirect ownership of at least fifty  
percent (50%) of the voting interest in the entity in question.  
8
 
10. CONSENT TO USE OF DATA  
You agree that Audiovox and its subsidiaries may collect and use technical and related information that  
does not personally identify you, including but not limited to offers opted into by you with Audiovox  
partners, technical information about your computer, system and application software, IP address and  
peripherals, that is gathered periodically to facilitate the provision of software updates, product support  
and other services to you (if any) related to the RCA Memory Manager Software and to verify compliance  
with the terms of this License. Audiovox may use this information, as long as it is in a form that does not  
personally identify you, to improve our products or to provide services or technologies to you.  
2. ARCSOFT CORPORATION EULA  
ARCSOFT CORPORATION  
END USER LICENSE AGREEMENT  
IMPORTANT: READ CAREFULLY BEFORE DOWNLOADING OR INSTALLING THIS SOFTWARE!  
The following is a legal software license agreement between you, the software end user, and ArcSoft, Inc.  
Carefully read this license agreement before using the relevant ArcSoft software ("Software"). Installing the  
Software on a computer or other hardware device indicates that you have read this license agreement and  
agree to its Terms.  
1. Grant of License. This license permits you to use one copy of the Software included in this package or  
product on any single computer. For each software licensee, the program can be "in use" on only one  
computer or hardware device at any given time. The Software is "in use" when it is either loaded into RAM  
or installed into the hard disk or other permanent memory of a computer or other hardware device. A  
special license permit from ArcSoft is required if the program is going to be installed on a network server  
for the sole purpose of distribution to other computers. You may not modify, translate, reverse assemble,  
decompile, disassemble or otherwise attempt (i) to defeat, avoid, bypass, remove, deactivate or otherwise  
circumvent any software protection mechanisms in the Software, including without limitation any such  
mechanism used to restrict or control the functionality of the Software, or (ii) to derive the source code or  
the underlying ideas, algorithms, structure or organization from the Software (except to the extent that  
such activities may not be prohibited under applicable law).  
2. Copyright. The Software contained in this package or device is protected by United States copyright  
laws, international treaty provisions, and all other applicable national laws. The Software must be treated  
like all other copyrighted materials (e.g. books and musical recordings). This license does not allow the  
Software to be rented or leased, and the written materials accompanying the Software (if any) may not be  
copied.  
3. Ownership. Title, ownership rights, and all intellectual property rights in and to the Software and any  
accompanying documentation, and any copy of the foregoing, shall remain the sole and exclusive  
property of ArcSoft and/or its third party licensors. You agree to abide by the copyright law and all other  
applicable laws. You acknowledge that the Software contains valuable confidential information and trade  
secrets of ArcSoft and/or its third party licensors.  
4. Software Updates. The Software may sync up with ArcSoft's servers to check for available updates to the  
Software, such as bug fixes, patches, enhanced functions, missing plug-ins and new versions (collectively,  
"Updates"). The Software sends ArcSoft's servers a request for the latest Software version information. If a  
newer version is available, the Software will give you the option of downloading it. The Software will ask  
for permission before downloading an updated version. By installing the Software and not disabling the  
automated check for Updates, you hereby agree to automatically request and receive Updates from  
ArcSoft's servers.  
9
 
5. Warranty Disclaimer. NO WARRANTIES, EITHER EXPRESS OR IMPLIED, ARE MADE WITH RESPECT TO THIS  
SOFTWARE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES FOR NON-INFRINGEMENT OF INTELLECTUAL  
PROPERTY, AND ARCSOFT EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED HEREIN. YOU ASSUME THE  
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE SOFTWARE. SHOULD THE SOFTWARE PROVE  
DEFECTIVE, YOU, AND NOT ARCSOFT OR AN AUTHORIZED RESELLER, ASSUME THE ENTIRE COST OF  
NECESSARY SERVICING, REPAIR, OR CORRECTION. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE  
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. THIS  
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY  
FROM JURISDICTION TO JURISDICTION.  
6. Limited Liability. YOUR SOLE REMEDY AND THE ENTIRE LIABILITY OF ARCSOFT AND ITS LICENSORS ARE  
SET FORTH ABOVE. IN NO EVENT WILL ARCSOFT AND ITS LICENSORS BE LIABLE TO YOU OR ANY OTHER  
PERSON FOR ANY DAMAGES, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES,  
LOST PROFITS, LOST SAVINGS, OR OTHER DAMAGES ARISING OUT OF USE OF OR INABILITY TO USE SUCH  
SOFTWARE, EVEN IF ARCSOFT OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGES. BECAUSE SOME STATES/JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF  
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.  
7. Export. You will not export or re-export the product incorporating the Software without the appropriate  
United States or foreign government licenses.  
8. U.S. Government Restricted Rights. If you are a unit or agency of the United States government, the  
Software and related documentation are deemed to be "commercial computer software" and "commercial  
computer software documentation," respectively, pursuant to DFAR Section 227.7202 and FAR Section  
12.212(b), as applicable. Any use, modification, reproduction, release, performing, displaying or disclosing  
of the Software and/or the related documentation by the United States government shall be governed  
solely by the Terms of this Agreement and shall be prohibited except to the extent expressly permitted by  
the Terms of this Agreement. Any technical data provided that is not covered by the above provisions is  
deemed to be "technical data commercial items" pursuant to DFAR Section 227.7015(a). Any use,  
modification, reproduction, release, performing, displaying or disclosing of such technical data shall be  
governed by the Terms of DFAR Section 227.7015(b).  
9. High Risk Activities. The Software is not fault-tolerant and is not designed or intended for use in  
10  
 
hazardous environments requiring fail-safe performance, or any other application in which the failure of  
the Software could lead directly to death, personal injury, or severe physical or property damage  
(collectively, "High Risk Activities"). ARCSOFT EXPRESSLY DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY  
OF FITNESS FOR HIGH RISK ACTIVITIES.  
10. Privacy Policy. The Software registration and activation process may require you to provide personally  
identifying information such as your name, phone number, address, and email address. ArcSoft will not  
share or sell such information with any third party except as necessary to provide products you've  
requested.  
11. Usage Tracking. To improve product usability, ArcSoft may log information about the usage information  
of selected product features. Such usage information will not be collected with any corresponding  
identifying information so that usage anonymity will be preserved.  
12. Termination. Your rights with respect to the Software may be terminated, either immediately or after a  
notice period not exceeding thirty (30) days, upon unauthorized copying of the Software or failure to  
comply with the restrictions contained in this license agreement. Upon Termination of the license, you  
shall return all copies of the Software to the party from which the Software was acquired.  
13. Governing Law. If this product was purchased in the United States, this Agreement is governed by the  
laws of the state of California; otherwise, local laws may apply.  
11  
 
Getting started  
Dear RCA customer,  
Thank you for purchasing the RCA Small Wonder Camcorder. You can manage your recordings on your  
computer with the RCA Memory Manager included with this product.  
To start using your camcorder, please follow the setup instructions in the following pages.  
1. Content of the box  
Small Wonder Camcorder  
4 x AAA batteries  
USB cable  
CD-rom  
AV cable  
Quick Start Guide  
2. Battery Installation  
3
2
4
1
Slide up to lock.  
Push (to the right) to  
unlock.  
Observe the polarities.  
The camcorder can also be powered by USB. Refer to Connecting to a PC section for connecting details.  
When the camcorder is connected to a PC, three options will be displayed: USB connect, Web cam and  
USB power. Press + or - to select USB power and press RECORD to confirm.  
12  
 
3. Inserting SD memory card  
An SD memory card (not included) is needed for recording.  
Lift up the cover  
As the memory card is small in size,  
Push the card in  
it is recommended to use a small  
until a click is heard  
coin to help insert or remove it.  
To remove card, push card in until a click is heard, then slowly release the card. As card is under minimal  
tension when locked in memory slot, please use care when removing.  
Internal memory is not available. An SD memory card is recommended for recording. (SD  
memory card not included)  
4. Turning on the camcorder  
Slide and hold the power switch until the camcorder turns on.  
Slide and  
hold  
Memory card  
indicator  
Recording quality  
Battery indicator  
Slide and hold the power switch to turn off the camcorder.  
The camcorder will automatically turn off after 3 minutes if not in use.  
Refer to the following pages for more information on recording and other operations.  
13  
 
5. Resetting the camcorder  
To reset the camcorder (if it is not functioning properly), remove the batteries and re-install.  
6. Setting date and time  
It is recommended to set the date and time before using the camcorder. Refer to the Menu settings  
section for more information.  
14  
 
General controls  
General controls  
SD card slot (Lift up the cover to show the card slot)  
Recording indicator  
Microphone  
On/off switch  
Lens  
USB (Lift up the cover to  
access the connector)  
Camcorder strap hole  
Tripod screw hole  
AV output  
LCD screen  
Delete  
recordings  
Play/pause  
MODE  
Setup menu  
Record  
Switch  
between  
Photo  
preview and  
Video preview  
modes  
Audio speaker  
+/– Adjust volume during playback; zoom during  
record and preview  
/
– Skip to previous or next recording  
15  
 
Operation modes  
There are three basic modes for operating the camcorder: Video preview mode, Photo preview mode and  
Playback mode. It will always launch in video preview mode after being switched on. Refer to the diagram  
below for switching between modes and read relevant sections in the user manual for detailed operations.  
Switch on  
Press  
MODE  
Photo preview  
Video preview  
mode2  
(read Taking photos  
section)  
mode1  
(read Recording  
videos section)  
Press  
MODE  
To end Playback mode, simply press  
RECORD which will then return  
the camcorder to Video preview  
mode  
Press PLAY/PAUSE  
Playback mode  
(read Playback  
mode section)  
t
16  
 
Recording videos  
Recording quality  
1. In Video preview mode, press MENU to show the camcorder menu.  
2. Press - or + to highlight Quality within the Video Menu  
3. Press RECORD to select Quality which will then expose the choices of HQ and WebQ.  
4. Press - or + to highlight the desired Quality from HQ or WebQ, then press REC to save that setting.  
5. Press MENU to exit the camcorder menu. The selected setting (HQ or WebQ) appears on the display  
screen during preview.  
Quality settings  
Settings  
Recommended for:  
Resolutions (pixel) and  
Frame Rate (FPS)  
Approx. recording  
durations on a 32GB  
SD memory card*  
HQ mode  
Viewing on TV & High video 640 x 480 @ 30fps  
quality  
22 hours  
WebQ (Web  
Quality mode)  
Uploading to and viewing  
on the web  
320 x 240 @ 30fps  
33 hours  
* Actual recording time and capacity will vary depending on type of video content being recorded, system  
requirements, and other factors.  
17  
 
Recording videos  
1. In Video preview mode, press the red RECORD button to begin recording.  
Video recording indicator  
Elapsed time  
While recording, the red recording light on the camcorder front will turn on.  
2. Press PLAY/PAUSE to pause a recording.  
Pause indicator  
Elapsed time  
A pause indicator replaces the red RECORD indicator  
To resume recording, press PLAY/PAUSE  
at the top left corner of the screen.  
.
3. Press + or – to zoom in or out before or during recording.  
4. Press the red RECORD button to stop recording.  
18  
 
Taking photos  
To take photos  
1. In Photo preview mode, press RECORD to take photos.  
The photo resolution is 3 megapixels which is interpolated from a 1 megapixel sensor.  
2. After taking a photo, please allow a few seconds for image processing before the next photo can be  
taken.  
19  
 
Playback mode  
Playing back recordings  
1. Press PLAY/PAUSE to enter Playback mode and start playback of the most recent recording (video/  
photo).  
Type of file (Video/  
Photo)  
Current file number/Total number of files  
2. Press + or – during playback to adjust volume (video only).  
3. Press PLAY/PAUSE to pause playback.  
Press PLAY/PAUSE again to resume playback.  
Pause indicator  
Remaining  
playback time  
20  
 
4. To select another video, press or to cue the previous or next video.  
Type of file  
(Video/Photo)  
Current file number/Total number of files  
5. When video playback stops, press MODE  
or RECORD to return to Video preview mode. (Press  
RECORD to stop video playback)  
21  
 
Deleting  
To delete one recording  
1. Press or in Playback mode to select file.  
2. Press DELETE.  
3. Press + or - to select One.  
4. Press the red RECORD button.  
5. Press + or - to select Yes and press the red RECORD button to confirm delete.  
To delete all recordings  
1. Press DELETE in Playback mode and press + or - to select All.  
2. Press the red RECORD button.  
3. Press + or - to select Confirm and press the red RECORD button to confirm deletion of all recordings.  
22  
 
Menu settings  
Using the camcorder menu  
1. To access the menu for photo taking, press MENU in Photo preview mode. To access the menu for video  
taking, press MENU in Video preview mode.  
2. Press + or – to highlight a menu option.  
3. Press RECORD to enter the highlighted menu option.  
4. Press + or – to change the setting.  
5. Press RECORD to save settings.  
6. Press MENU to exit the camcorder menu.  
Menu options and settings  
Menu options Available settings  
Video Quality  
HQ/WebQ  
Date  
YYYY-MM-DD  
HR : MM AM  
Time  
Language  
TV Output  
Key tone  
English, Francais, Espanol  
NTSC(US), PAL  
On, Off  
Format1  
Yes, No  
Restore Settings  
System Info  
Yes, No  
Show the current firmware version  
1 Format the camcorder will remove all data files. Backup your media before formatting the camcorder.  
23  
 
Connecting to external devices  
Viewing videos on TV  
1. Plug in the AV cable (provided) – Insert the single connector end into the camcorder (AV jack) and  
connect the double connector ends to the corresponding video (yellow) and audio (white) input jacks  
on the TV.  
2. Turn on the TV and the camcorder.  
3. Switch the TV to the selected video input.  
Refer to your TV manual for instructions.  
4. You may play and delete videos viewed on the TV by using the camcorder buttons.  
The default TV output standard is NTSC. You can switch it to PAL standard by going to the  
camcorder menu. Refer to "Menu settings" for more information.  
Recording videos to VHS tape or DVD  
1. Plug in the AV cable (provided) – Insert the single connector end into the camcorder and connect the  
double connector ends to corresponding video (yellow) and audio (white) inputs of the recording  
device (VHS or DVD recorder).  
2. Turn on the camcorder and the recording device.  
3. Switch recording device to the video input connected to the camcorder.  
Refer to your user manual of the recording device for instructions.  
4. Start recording of your recording device. Press PLAY/PAUSE to playback the file you wish to record.  
After finishing current video or photo playback, press to skip to next video or photo and then press  
PLAY/PAUSE to start playback (Video file only).  
24  
 
Managing videos on your computer  
Computer system requirements  
Windows: Windows® XP (SP2 or higher) or Windows Vista™ or Windows® 7  
Pentium 4 1.6 GHz or equivalent AMD Athlon processor  
512 MB RAM (1 GB recommended)  
300 MB available hard disk space  
1024 x 768 pixels, 16-bit color monitor or higher  
Internet Access (broadband recommended)  
Macintosh: OS X 10.5,10.6  
Intel Core Duo processor (or higher)  
768 MB RAM (1GB recommended)  
300 MB free hard drive space for program installation  
1024 x 768 pixels or higher recommended  
Internet Access (broadband recommended)  
Connecting to a PC  
1. Connect the supplied USB cable to the connection jack. USB connector standard: mini-B  
2. Connect the other end of the cable to the computer.  
USB port of  
your computer  
Lift up the cover  
USB cable  
3. There are three options: USB connect, Web cam and USB power. Press + or - to select USB connect and  
press RECORD to confirm.  
4. Place the supplied CD-ROM in the CD-ROM tray.  
5. Windows: To access the Memory Manager 3 installer, go to My Computer (XP users) /go to Computer  
(Vista and 7 users) in the Start menu, find and open the drive letter associated with the CD rom and  
then double-click the MemoryMgr3_Windows_Installer. exe file to launch the installer. The RCA  
Detective application is installed with Memory Manager 3 and will automatically run the Memory  
Manager 3 application when your camcorder is connected to the PC.  
Mac: To access the Memory Manager 3 installer, double-click the CD rom volume. Double-click the  
RCAMacInstallers.dmg disk image in the CD rom volume. Locate the RCAMacInstallers volume on  
the desktop and Double-click on it. Double-click the MemoryMgr3 Mac Installer file in the  
RCAMacInstallers volume to start the installation. After the Memory Manager 3 installation has  
completed, double-click the RCA Detective Installer file in the RCAMacInstallers volume to install the  
RCA Detective application, which will automatically run the Memory Manager 3 application when your  
camcorder is connected to the Mac.  
Camcorder cannot record while connected to the PC.  
Memory Manager is proprietary software licensed by Audiovox Corporation.  
25  
 
About RCA Memory Manager  
The included RCA Memory Manager application lets you:  
Browse and play videos  
Delete videos  
Save videos to your computer  
Edit videos by simply drag-and-drop  
For more detailed instructions on using RCA Memory Manager, please refer to the help section  
in the software.  
Viewing videos on PC  
To ensure that videos can be managed and played on your PC:  
Make sure to install the included Memory Manager application.  
*
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.  
Using camcorder as Web Camera in PC  
To use the camcorder as a Web Camera in your PC, a driver file is needed. Please go to  
After downloading the driver file, follow the instructions and complete the installation.  
Connect the camcorder to the PC, after the camcorder displays the selection menu, select the Web Cam  
option and press RECORD . Now the camcorder is connected as Web Camera to the PC.  
26  
 
Additional information  
Tips and troubleshooting  
Cannot turn on the camcorder.  
Make sure the batteries are in good condition.  
SD card cannot be detected by camcorder.  
Make sure the SD card is inserted properly. Remove and insert the card from the card slot again when  
the camcorder is powered off.  
Camcorder not turned on after connected to PC.  
The camcorder battery may be very low. Slide the power button to turn on the camcorder after  
connecting to PC.  
Cannot record videos.  
Make sure the memory space is not full.  
Available time for recording has significantly reduced.  
Make sure you have properly selected the video recording quality before recording.  
The recording time and date are incorrect.  
Make sure you have properly set the date and time in the setting menu. Refer to "Menu settings" for  
more information.  
The keytone is annoying. Can it be switched off?  
Yes. Refer to the Menu settings section for more information.  
No sound when playing back recordings.  
Adjust the volume by pressing + or – during playback.  
Pictures are distorted when videos are played back via connected TV set.  
Make sure you have correctly selected the TV output system (PAL or NTSC) from the setting menu. Refer  
to the Menu settings section for more information.  
Can I retrieve deleted videos and photos?  
Unfortunately, deleted videos cannot be retrieved.  
The camcorder is not functioning properly.  
Remove and re-install batteries, and then turn on again. If problem still exist, replace with new batteries.  
Cannot view recorded videos on PC.  
Install the included Memory Manager software and use it to view videos on your PC.  
My friends cannot view the videos I have sent them.  
Use the SHARE functions of the Memory Manager for sharing videos with friends and family. The native  
files from the camcorder may not play in other computers.  
27  
 
Visiting RCA website  
Latest software and firmware  
RCA Memory Manager Software  
User manual  
Frequently asked questions (FAQ)  
Customer service and technical support information  
28  
 
Technical specifications  
Battery:  
4 x AAA battery  
Size and frame rate of video recordings:  
HQ mode: 640 x 480 pixels @ 30fps (MJPEG video compression, AVI file format)  
WebQ mode: 320 x 240 pixels @ 30fps (MJPEG video compression, AVI file format)  
Size of still images:  
640 x 480 pixels (JPG)  
Recording media:  
SD card (not included)  
Maximum recording time (approximate figures):  
Video Recording Modes  
HQ (High Quality mode)  
WebQ (Web Quality mode)  
Maximum recording time with 32 GB SD card  
22 hours  
33 hours  
* Actual recording time and capacity will vary depending on type of video content being recorded, system  
requirements, and other factors.  
LCD screen:  
1.8 inches  
Microphone:  
Mono microphone  
29  
 
Warranty information  
12 Month Limited Warranty  
Applies to RCA Camcorders  
AUDIOVOX ACCESSORIES CORP. (the Company) warrants to the original retail purchaser of this product that  
should this product or any part thereof, under normal use and conditions, be proven defective in material  
or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or  
replaced with reconditioned product (at the Company’s option) without charge for parts and repair labor.  
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof  
of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the  
Company at the address shown below.  
This Warranty does not extend to the elimination of externally generated static or noise, to correction of  
antenna problems, loss/interruptions of broadcast or internet service, to costs incurred for installation,  
removal or reinstallation of product, to corruptions caused by computer viruses, spyware or other malware,  
to loss of media, files, data or content, or to damage to tapes, discs, removable memory devices or cards,  
speakers, accessories, computers, computer peripherals, other media players, home networks or vehicle  
electrical systems.  
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has  
suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect,  
accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE  
COMPANY’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED  
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY  
PURCHASER FOR THE PRODUCT.  
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING  
ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN  
WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED  
WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF  
ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR  
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is  
authorized to assume for the Company any liability other than expressed herein in connection with the  
sale of this product.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation  
of incidental or consequential damage so the above limitations or exclusions may not apply to you. This  
Warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
Recommendations before returning your product for a warranty claim:  
If your product is capable of storing content (such as an mp3 player, voice recorder, camcorder, digital  
photo frame, etc), it is recommended to make periodic backup copies of content stored on the product.  
If applicable, before shipping a product, make a back up copy of content or data stored on the device.  
Also, it is advisable to remove any personal content which you would not want exposed to others. IT IS  
LIKELY THAT CONTENTS AND DATA ON THE DEVICE WILL BE LOST DURING SERVICE AND  
REFORMATTING. AUDIOVOX ACCEPTS NO LIABILITY FOR LOST CONTENT OR DATA, OR FOR THE  
SECURITY OF ANY PERSONAL CONTENT OR DATA ON THE RETURNED DEVICE. Product will be returned  
with factory default settings, and without any pre-loaded content which may have been installed in the  
originally purchased products. Consumer will be responsible for reloading data and content. Consumer  
will be responsible to restore any personal preference settings.  
30  
 
Warranty information  
Properly pack your unit. Include any remotes, memory cards, cables, etc. which were originally provided  
with the product. However DO NOT return any removable batteries, even if batteries were included with  
the original purchase. We recommend using the original carton and packing materials. Ship to  
Audiovox Electronics Corp.  
Attn: Service Department.  
150 Marcus Blvd.  
Hauppauge N.Y. 11788  
1-800-645-4994  
For Canada Customers, please ship to:  
Audiovox Return Centre  
c/o Genco  
6685 Kennedy Road,  
Unit#3, Door 16,  
Mississuaga, Ontario  
L5T 3A5  
31  
 
Illustrations contained within this publication are for representation only and subject to change.  
The descriptions and characteristics given in this document are given as a general indication and not as a  
guarantee. In order to provide the highest quality product possible, we reserve the right to make any  
improvement or modification without prior notice.  
Visit http://store.audiovox.com to find the  
best accessories for your products.  
© 2011 Audiovox Accessories Corporation  
111 Congressional Blvd., Suite 350  
Carmel, IN 46032  
Trademark(s) ® Registered  
v3.0 (1.0.3.0)  
 

RCA CRT Television F27667 User Guide
RocketFish Mouse RF NANMSE User Guide
RocketFish Network Card RF BPRACDC2 User Guide
RuggedCom Switch RS940G User Guide
Samson Speaker DB1500A User Guide
Samsung Security Camera SNC B5399P User Guide
Sanyo Flat Panel Television CE52SR1 User Guide
Seagate Computer Drive 100516232 User Guide
Sears Battery Charger 20071460 User Guide
Sears Humidifier 758144131 User Guide