PYLE Audio TV Mount PSW116MF1 User Guide

Step 3: Hanging display  
Firstly lift the bracket mounted display over the wall mount. And then hook the  
brackets over the top of the wall mount. Rotate the display let the bottom of the  
brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe  
bolts into the bottom of the brackets and lock it, as shown in Fig.3b.  
Fixed Flat Panel TV Bracket  
Multifunctional double deck wall mount  
INSTALLATION GUIDE  
Warning: Some TV require two people to lift, as we are not responsible for any  
personal injury or product damage due to mishandling.  
Item No.:PSW116MF1  
UP  
UP  
UP  
UP  
2
1
3
Fig 3a  
Fig 3b  
Thank you for choosiing our products  
Easy installing: Just hang up the display  
Safety: locking by spinning bolt on the bottom  
Max load capacity:60kgs/132lbs  
TV size range: 36"~65"  
Inside has balance adjust system  
Pyle Audio  
1600 63rd st , Brooklyn, NY, 11204  
(718)236-8000  
www.pyleaudio.com  
Bulit in leveler system  
MADE IN CHINA  
-8-  
IMPORTANT: If don’t understand about right install ways, please  
consult to normal installing specialist.  
 
Step 2: Attach mount to wall  
WARNING  
First, determine the height of stand  
The best height of stand is parallel to eyelevel of a person who sitting on a couch.  
Normally, the horizontal distance of eyelevel is about 4’ from ground level.  
The following two conditions are for determining the perfect height of stand:  
1) the distance between wall and couch(Fig 2a).  
We are not responsible for any personal injury or product damage due to mishandling,  
incorrect mounting, incorrect assembly or incorrect use of this product.  
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold  
cinder block walls. If you are uncertain about the nature of your wall, please consult a  
qualified contractor. If the hardware you required is not included please contact your  
local hardware store.  
2) the distance of eyelevel from ground level plus the distance measured from  
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 2a).  
For example:  
Caution:  
This Product LCD /Plasma Wall Mount Bracket is intended for use only  
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’  
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’  
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’  
The perfect height of stand centre will be anywhere within b, where you feel  
comfortable for viewing.  
with the maximum weights indicated .See apparatus instructions .Use with products  
heavier than the maximum weights indicated may result in instability causing possible  
injury .  
Step 1: Attach bracket to TV  
According your display hole's distance to choose the bracket :  
Short bracket -up to 400mm height of landed inserts  
Long bracket -up to 600mm height of landed inserts  
15 degree  
viewing angle  
b
Check your TV manual to confirm the diameter of bolt to be used or choose an  
appropriate bolt according to size, height and position of the holes on your TV. See  
pages 4-5 of these instructions for examples.  
eyelevel  
For correct installing, make sure that hook of every bracket must facing down. Use  
selected bolts, spacers and washers for installing bracket at the back of display.  
Adjust two brackets to equal heights and level. Once aligned, tightly secure the  
bolts. Note: the " UP"side on the top. As shown in Fig.1.  
a
IMPORTANT: Don't force the bolt into the hole, which will cause a damage of  
Fig 2a  
equipments and injure of person. Don't use electric drill to fasten any bolts.  
Fig.1  
-3-  
-6-  
 
Following examples shows how to use bolts, spacers and square washers.  
2. Some displays have curved backs with  
recessed mounting lands(Fig.a). It will  
require the use of spacer. For this display,  
install a spacer(M) between display and the  
bracket. As shown in Fig 1b.  
1.Some displays have vertical backs. No spacer is required. Install the bracket directly  
to the back of display by using bolts and square washers provided. As shown in Fig.1a.  
Fig a  
M4 Fig bit  
M5 Fig bit  
M5 Fig bit  
M6 Fig bit  
M
I
M
I
I
A,B  
F
2
2
2
C
G
2
I
2
2
I
E
D
I
M
2
H
I
M6 Fig bit  
M8 Fig bit  
M8 Fig bit  
Fig 1b  
Fig 1a  
-5-  
-4-  
 

Radio Shack Clock 63 974 User Guide
Radio Shack Door 63 1124 User Guide
Remington GPS Receiver OCN6 User Guide
Renesas Network Card REG10J0052 0200 User Guide
Ryobi Trimmer P2601 User Guide
Salton Waffle Iron WM 1186 User Guide
Samsung Cell Phone DCS User Guide
Samsung Home Theater System HT DL100 User Guide
Samsung Printer SCX 5x30 User Guide
Sanyo Camcorder VPC HD1000 User Guide