Kodak Film Camera TI 2037 User Manual

TECHNICAL DATA / PRINTED CIRCUIT BOARD FILM  
KODAK PRECISION LINE  
Contact Film UCA7  
—High Complexity PCB Starts With the Right Phototools—  
May 2005 TI-2037  
• Designed for making contact phototools from  
photoplotter output or other line work.  
DARKROOM RECOMMENDATIONS  
This film can be safely handled for up to a total of  
60 minutes, before or after exposure, in up to 40 footcandles  
(430 lux) of roomlight illumination substantially free of  
ultraviolet (UV) energy. Such illumination is supplied by  
yellow fluorescent lamps (warm white preferred) and white  
fluorescent lamps covered by UV-absorbing or modified by  
UV-absorbing plastic diffusers. Other roomlight sources  
contain varying amounts of UV energy, and their roomlight  
tolerances for this film should be tested under the specific  
conditions of use.  
• Negative working, slow speed, ultraviolet sensitivity  
• Expose with high intensity metal halide or pulsed-xenon  
source  
• Use in white fluorescent illumination covered with  
ultraviolet-absorbing material or in yellow fluorescent  
illumination  
• Very dimensionally stable ESTAR Thick Base with  
antistatic properties under a wide range of humidity  
conditions, both before and after processing.  
• Excellent scratch and abrasion resistant overcoat.  
STORAGE AND HANDLING  
Keep unexposed film and processed film in a cool, dry place.  
Process film as soon as possible after exposure.  
• Produces high image density at line-for-line exposures  
with minimum pinholes.  
• Sufficient matte level on both sides to minimize  
Newton's rings and to provide rapid drawdown in  
vacuum printing frames.  
EXPOSURE  
Expose with a multi-level high-intensity metal-halide  
exposure source. Optimum exposure should be determined  
bymeansofatrialexposureseries, followingtheequipment  
manufacturer's recommended procedures. Use a trial  
exposure time of 5 to 20 seconds at an exposure distance of  
127 to 152 cm (36 to 60 inches). Contact your Kodak  
representative for more information.  
• Can also be processed in a wide selection of machine  
developers including lith and rapid-access, along with  
KODAK ULTRALINE Developer and Replenisher.  
SUPPORT  
Dimensionally stable support.  
Note: Exposures for optimum line width reproduction are  
critical when using a broad light source, and when making  
base-to-emulsion exposures. Any light falloff from the  
center to the edge of the exposing source may affect overall  
reproductionqualityandintroduceproblemswithaccurate  
line-width reproductions.  
7-mil (0.18 mm)  
ESTAR Thick Base  
Precautionary: Contact the manufacturer of high intensity  
ultraviolet lamps for safety information pertaining to  
ultraviolet radiation and ventilation requirements due to  
ozone generation.  
©Eastman Kodak Company, 2005  
 
DIMENSIONAL STABILITY  
CURVES  
Dimensional stability is an all-inclusive term. In  
photography, it applies to size changes caused by changes in  
humidity and in temperature, and by processing and aging.  
The dimensional properties of ESTAR Base may vary  
slightly in different directions within a sheet; the differences  
that may exist, however, are not always equal between the  
length and width directions.  
Characteristic Curve  
7.0  
26 sec  
Exposure:  
Process: RA 2000 Developer and Replenisher,  
95F, 22 sec  
Densitometry: Diffuse visual  
6.0  
5.0  
4.0  
3.0  
2.0  
1.0  
Differences in size change between length and width  
directions should be within 10 percent of each other.  
0.0  
0.0  
F009_0415AC  
1.0  
2.0  
3.0  
4.0  
LOG EXPOSURE (lux-seconds)  
3
KODAK PRECISION LINE Contact Film UCA7 TI-2037  
 
KODAK PRECISION LINE Contact Film UCA7  
MORE INFORMATION  
For the latest version of technical support publications for  
Kodak products, visit Kodak on-line at:  
If you have questions about Kodak products, call Kodak.  
In the U.S.A.:  
1-800-242-2424, Ext. 19, Monday–Friday  
9 a.m.–7 p.m. (Eastern time)  
In Canada:  
1-800-465-6325, Monday–Friday  
8 a.m.–5 p.m. (Eastern time)  
From outside the US/Canada: 1-716-724-4000  
Note: The Kodak materials described in this publication for  
use with UCA7 Film are available from dealers who supply  
KODAK PROFESSIONAL Products. You can use other  
materials, but you may not obtain similar results.  
NOTICE: The sensitometric curves and data in this publication represent product tested under the conditions  
of exposure and processing specified. They are representative of production coatings, and therefore do not apply  
directly to a particular box or roll of photographic material. They do not represent standards or  
specifications that must be met by Eastman Kodak Company. The company reserves the right to change  
and improve product characteristics at any time.  
Aerial and Industrial Markets Business  
EASTMAN KODAK COMPANY ROCHESTER, NY 14650  
KODAK PRECISION LINE Contact  
Film UCA7  
Kodak, Estar, Precision Line, and Ultraline are trademarks.  
Revised 5-05  
Printed in U.S.A.  
KODAK Publication No. TI-2037  
 

Indesit Oven FIU20 MK2 User Manual
Insignia Network Cables NS PU965XF User Manual
Intellinet Network Solutions Home Security System 550703 User Manual
IOGear Computer Keyboard GKM512 User Manual
Jade Range Oven KC 24 User Manual
JBL Portable Speaker j50 User Manual
Jenn Air Microwave Oven JMC2127 User Manual
Jensen Tools Car Satellite Radio System DLP2500 User Manual
John Deere Pressure Washer AC 3500GHH User Manual
JVC Computer Drive VR D0U User Manual