Knoll Stereo Receiver IR230 User Manual

IR230 Infrared Receiver Specifications:  
IR230  
Installation Instructions v1.2  
Peep-hole Infrared Receiver  
Specifications  
Infrared carrier frequency: 30-60kHz  
Indoor reception range:  
Nominal reception angle:  
Maximum wire length:  
30-40 feet (6-8 meters)  
50 degrees off axis  
1000’ (300m) or more with larger  
Warning: To be installed and/or used in accordance with  
appropriate electrical codes and regulations.  
gauge wire  
Introduction: Thank you for your purchase of a Knoll IR230  
infrared receiver. This receiver features the ability to pick up a  
remote control infrared signal and relay it on wires to another  
location up to 1000’ (or more).  
Wire requirements:  
3 conductors, minimum 24-gauge  
to 200’; 22-gauge up to 500’;  
20-gauge to 1000’  
Unregulated 12VDC, 40mA  
0.6” x 2” (15mm x 50mm)  
½” (12mm)  
Power requirements:  
Dimensions:  
Cut out hole dimensions  
Cord length  
Features:  
75” (2 meters)  
Primarily designed to for mounting in panels, doors,  
cabinets etc.  
Will relay almost all remote control types (except som
B & O and Elite models).  
Can be connected with almost any 3-conductor wire  
including cat 5.  
Requires very little power. Suggest using PS1202 12  
VDC (200 mA) for up to 5 IR21s.  
Up to 10 or IR230s, IR21s and other compatible mode
can be connected in a single system.  
Brass and white color bezel supplied  
Small and CFL and sunlight ready design  
Requires 12VDC power supply, emitter(s) and IR54, or  
IR55 connection block.  
Warranty  
Knoll Systems warrants its products sold in the USA and Canada by authorized  
Knoll dealers to be free of defects in materials and workmanship. This warranty  
extends for three full years from the date of purchase by the original consumer.  
Any products returned to Knoll Systems and found to be defective by Knoll  
Systems within the warranty period will be repaired or replaced at Knoll Systems  
option, at no charge. Knoll Systems will not be responsible for the actual cost of  
installation or removal of the product, nor for any incidental or consequential  
damages. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation may not apply to you. This  
warranty gives you specific legal rights. You may have additional legal rights  
that vary from state-to-state.  
Installation Tips  
1. Follow all local electrical & building code requirements.  
2. The IR230 is usually mounted in a panels, door, cabinet or  
plate. It does not normally require a junction box. For easy  
installation and to ensure reliability, it is suggested that a  
PS1205 (500 mA) 12 VDC unregulated power supply, IR31  
(single) or IR34 (dual) emitters and one of the following: IR54  
(decora inwall style, 4 output) or IR55 (tabletop style, 4 output)  
connection block, be used.  
145 Tyee Drive Point Roberts, WA 98281  
12140 Horseshoe Way, Richmond BC V7A 4V4  
Telephone: (604) 272-4555, Fax: (604) 272-5595  
Made in China Knoll Systems All Rights Reserved  
3. Wires can be solid or stranded, shielded or unshielded with a  
minimum of 28-gauge for runs under 200’, 22-gauge for runs  
 

Ingersoll Rand Cordless Sander 313A User Manual
Init TV Video Accessories IT TVDLP101 User Manual
Jacuzzi Hot Tub EE15 User Manual
Jenn Air Refrigerator 41007605 User Manual
JL Audio Portable Speaker XR650 CS User Manual
JVC Computer Monitor TM H150CG User Manual
JVC Digital Camera GR D290 GR D270 User Manual
Kensington Laptop 33367 User Manual
Kensington Network Card 33335 User Manual
KitchenAid Refrigerator KBFS25EWMS5 User Manual