8900 Keystone Crossing, Suite 1220
Indianapolis, Indiana 46240
.
.
•
1 800 KLIPSCH
Make sure you return your
warranty card so that we may
keep you up-to-date on new
Klipsch products and promo-
tions. As always, if you have
any questions, contact your
local authorized Klipsch dealer.
For your records:
Model
Serial Number
Date Purchased
Dealer Name
193098(Rev.1)
20M0499
CAUTION:
RIS K OF ELECTRIC S HOCK!
DO NOT OP EN!
!
CAUTION! To reduce the risk of electric shock and fire, do not remove the cover or back plate of this
device. There are no user-serviceable parts inside. Refer repairs to a Klipsch authorized service center.
AVIS: Risque de choc electricque, ne pas ouvrir.
!
!
CAUTION! The international symbol of a lightning bolt inside a triangle is intended to caution you to
uninsulated “dangerous voltage” within the device’s enclosure. The international symbol of an exclama-
tion point inside a triangle is intended to alert you to the presence of important operating, maintenance
and servicing information in the manual accompanying the device.
CAUTION! To prevent electrical shock, match the wide blade of the plug on the power cord to the wide
slot on the power outlet and insert fully. ATTENTION: Pour eviter les chocs electriques, introduire la
lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond.
!
!
CAUTION! To reduce the risk of electrical shock, do not expose this equipment to rain or moisture.
1. Read Instructions. All safety and operating instructions should be read before operating the device.
2. Retain Instructions. The safety and operating instructions should be retained for future reference.
3. Heed Warnings. All warnings on the device and in the operating instructions should be adhered to.
4. Follow instructions. All operating and safety instructions should be followed.
5. Water and Moisture. The device should never be used in, on or near water due to risk of fatal shock.
6. Carts and Stands. The device should only be used on carts or stands recommended by the
manufacturer.
7. Wall and Ceiling Mounting. The device should be mounted on a wall or ceiling only as recommended
by the manufacturer.
8. Ventilation. The device should always be located in such a way that it maintains proper ventilation.
It should never be placed in a built-in installation or anywhere that may impede the flow of air
through its heat sink or ventilation openings.
9. Heat. Never locate the device near heat sources such as a radiator, floor register, stove or other heat
generating device.
10. Power Supply. The device should only be connected to a power supply of the type described in the
operating instructions or as marked on the device.
11. Polarization. This product is equipped with a polarized line plug that has one blade wider than the
other. To prevent electrical shock, match the wide blade of the plug with the wide blade slot of the
receptacle and insert fully.
12. Power Cord Protection. Power cables should be routed so they are unlikely to be stepped on or
crushed by items placed on or against them. Pay special attention to where the plug enters a socket
or fused strip and to where the cord enters the device.
13. Cleaning. The device should be cleaned in accordance with the manufacturer’s instructions.
14. Periods of Non-Use. The device should be unplugged from the wall outlet when it is not in use for
extended periods.
Cut a long dot t ed line a nd m a il.
IF YOU P REFER, YOU CAN NOW REGIS TER ONLINE AT W W W .KLIP S CH.COM
For multiple speaker purchases, please fill out only one warranty card.
Name:
Street Address:
City/State/Zip:
Home Phone:
Work Phone:
E-mail Address:
Would you like to receive the latest product updates and news via e-mail? q Yes q No
Product Purchase
Model and serial number must be included to honor your warranty card. For multiple speaker
purchases, please fill out only one warranty card.
Model
Model
Model
Model
Model
Model
Serial Number
Serial Number
Serial Number
Serial Number
Serial Number
Serial Number
What store did you purchase your Klipsch products from?
Store Name:
State:
How did you hear about Klipsch? q Audio/Home Theater Magazine q Other Magazine q TV
q Radio q Newspaper q Trade Show q Friend q Retail Dealer q Direct Mail
Have you purchased Klipsch products before? q Yes q No
If yes, what products?
Product Name(s):
When do you hope to purchase additional loudspeakers? q 6 mos. – 1 yr. q 1–2 yrs. q 2–4 yrs.
How likely are you to consider Klipsch products for your upcoming purchases? q Very likely
q Somewhat likely q Doubtful
If doubtful, why? q Don’t carry product I’m looking for q Too expensive
q Klipsch dealer too far away q Other
Please tell us about you!
q Married q Single q Student
q Male q Female
Age: q 15-17 q 18-24 q 25-35 q 36-45 q 46-55 q 55-64 q 65+
Annual Household Income: q Under $25,000 q $25-35,000 q $35-50,000
q $75-100,000 q $100,000+
Klips ch Lim it ed W a r r a nt y
KLIPSCH, L.L.C. (“KLIPSCH”) warrants this product to be free from defects in materials and work-
manship (subject to the terms set forth below). For a period of five (5) years from the date of purchase,
KLIPSCH will repair or replace (at KLIPSCH’s option) this product or any defective parts (excluding
electronics and amplifiers) in this product. For products that have electronics or amplifiers, the warranty
on those parts is for a period of two (2) years from the date of purchase.
To obtain warranty service, please contact the KLIPSCH authorized dealer from which you purchased
this product. If your dealer is not equipped to perform the repair of your KLIPSCH product, it can be
returned, freight paid, to KLIPSCH for repair. Please call KLIPSCH at 1-800-KLIPSCH for instructions.
You will need to ship this product in either its original packaging or packaging affording an equal
degree of protection.
Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is
within the warranty period, must be presented to obtain warranty service.
This Warranty is invalid if (a) the factory applied serial number has been altered or removed from this
product or (b) this product was not purchased from a KLIPSCH authorized dealer. You may call 1-800-
KLIPSCH to confirm that you have an unaltered serial number and/or you purchased from a KLIPSCH
authorized dealer.
This Warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or modification of, or to any part of, the product. This Warranty does not
cover damage due to improper operation, maintenance or installation, or attempted repair by anyone
other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work. Any
unauthorized repairs will void this Warranty. This Warranty does not cover products sold AS IS or
WITH ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE
REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS
EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSO-
EVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PRACTICAL PURPOSE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or implied
warranties so the above exclusions may not apply to you. This Warranty gives you specific legal rights,
and you may have other rights which vary from state to state.
15. Dangerous Entry. Care should be taken that no foreign objects or liquids fall or are spilled inside
the device.
16. Damage Requiring Service. The device should be serviced by a Klipsch authorized service center when:
-The plug or power supply cord has been damaged.
-Objects have fallen or liquid spilled inside of the device.
-The device has been exposed to moisture.
-The device does not appear be operating properly or exhibits a marked change in performance.
-The device has been dropped or the cabinet has been damaged.
17. Service. The user should not attempt to service the device beyond what is described in the operating
instructions. All other servicing should be referred to qualified personnel. If dealer service is not
available, contact Klipsch customer service for a return authorization (RA) number before shipping.
18. Klipsch Customer Service: 800-554-7724
19. All return shipments should be made to:
Klipsch, L.L.C.
137 County Road #278
Hope, AR 71801
RA#…(return authorization number required)
W e W a nt Your Klips ch P r oduct t o Look a nd
S ound a s Good a s W hen it Left t he Fa ct or y.
P lea s e Check P r om pt ly for Tr a ns it Da m a ge.
Each Klipsch product is individually tested for sonic quality and inspected for superior appearance
before it leaves the Hope, Arkansas factory. Your loudspeaker left the factory in perfect condition in
packaging carefully engineered to protect both the working parts and finish. However, in certain
extreme circumstances, the products may be damaged in transit.
To ensure that your loudspeaker is in its original condition, please inspect it immediately. If damage
is discovered, notify the authorized Klipsch dealer that the unit was purchased from or the trans-
portation company responsible for safe delivery. In the latter case, make a request for inspection from
the transportation company and hold the product in its original shipping carton for the inspector.
After a joint inspection report is made, file a claim with the transportation company.
Dea r Klips ch S yner gy S er ies Owner
Congratulations on your purchase of a Klipsch KSW Series powered subwoofer! Our fourth generation
KSW powered subwoofers will add an exciting new dimension to your home entertainment
system, providing outstanding bass reproduction of your favorite music and movies. The KSW models
provide more powerful amplifiers, all-new driver designs and greater ease of use, making them an
incredible value.
A Klipsch KSW subwoofer brings that “I’m part of the action” feeling to your home entertainment
system in a way few other components can. If this is your first Klipsch purchase, welcome to the
fold; if this is an additional Klipsch purchase, we thank you for your loyalty. When it comes to the
best in home entertainment, Klipsch is a sound choice.
Please take the time to fill out the enclosed questionnaire and warranty registration card or if you
dealers in meeting your needs as a valued Klipsch customer. Should you have any questions or need
more information on Synergy or other Klipsch products, please contact us. We will be happy to
assist you, and welcome your feedback.
Thank you for choosing Klipsch loudspeakers.
Sincerely,
Fred S. Klipsch
Chairman & CEO
Com ponent S pecifica t ions
KS W 1 5
KS W 1 0
Type: 15" bass reflex, tuned port enclosure
Amplifier: Peak output power 800 watts into 16 ohms
FTC Rated Power: 265 watts into 16 ohms 22-100Hz
@ 1% THD maximum
Type: 10" bass reflex, tuned port enclosure
Amplifier: Peak output power 225 watts into 4 ohms
FTC Rated Power: 55 watts continuous, 22-125Hz
@ 1% THD maximum
Auto Power On: 2 second ON delay, 15 minute OFF delay
Frequency Response: 24-120Hz±3dB
Maximum Acoustic Output: 121dB 1/8 space 1 meter
Low Pass Crossover: Continuously variable from 40-120Hz,
24dB/octave slope above 120Hz
Auto Power On: 2 second ON delay, 15 minute OFF delay
Frequency Response: 29-120Hz±3dB
Maximum Acoustic Output: 110dB 1/8 space 1 meter
Low Pass Crossover: Continuously variable from 40-120Hz,
24dB/octave slope above 120Hz
Inputs: 2) Line level RCA phono jacks 1) Line level
dedicated LFE channel input (non-filtered) 2) High
level speaker terminals
Inputs: 2) Line level RCA phono jacks 2) High level speaker
terminals
Phase: Switchable 0-180 degrees
Drive Component: K-1070-K 10" (25.4cm) driver
Net Weight: 29 lbs. (13.18kg)
Outputs: 2) Line level RCA phono jacks with switchable
high pass filter between 50 and 100Hz 2) High level
speaker terminals with fixed high pass at 100Hz,
6dB/octave slope
Height: 15.5" (39.37cm)
Width: 13.5" (34.3cm)
Depth: 13.5" (34.3cm)
Phase: Switchable 0-180 degrees
Cabinet: Medium density fiber board construction (MDF)
Finish: Matte finish black vinyl
Drive Component: K-1072-K 15" (38.1cm) driver
Net Weight: 45 lbs. (20.45kg)
Height: 19.5" (49.53cm)
Voltage: 110/120 VAC 60Hz - Export Version 230
VAC 50/60Hz
Width: 17.5" (44.45cm)
Depth: 17.5" (44.45cm)
Cabinet: Medium density fiber board construction (MDF)
Finish: Matte finish black vinyl
Voltage: 110/120 VAC 60Hz - Export Version 230
VAC 50/60Hz
KS W 1 2
Type: 12" bass reflex, tuned port enclosure
Amplifier: Peak output power 441 watts into 4 ohms
FTC Rated Power: 105 watts continuous into 4 ohms,
22-100Hz @ 1% THD maximum
Auto Power On: 2 second ON delay, 15 minute OFF delay
Frequency Response: 26-120Hz±3dB
Maximum Acoustic Output: 113dB 1/8 space 1 meter
Low Pass Crossover: Continuously variable from 40-120Hz,
24dB/octave slope above 120Hz
Inputs: 2) Line level RCA phono jacks, 2) High level speaker
terminals
Outputs: 2) High level speaker terminals, High pass filtered
at 100Hz, 6dB/octave slope
Phase: Switchable 0-180 degrees
Drive Component: K-1071-K 12" (30.5cm) driver
Net Weight: 35 lbs. (15.9kg)
Height: 17" (43.18cm)
Width: 15" (38.1cm)
Depth: 15" (38.1cm)
Cabinet: Medium density fiber board construction (MDF)
Finish: Matte finish black vinyl
Voltage: 110/120 VAC 60 Hz - Export Version 230
VAC 50/60Hz
“S P EAKER IN” / ALL M ODELS
For parallel connection of the subwoofer and main speaker wires (main speakers full range), connect
the subwoofer input wires to the main channel, right and left, speaker outputs of your amplifier or
to a secondary set of main speaker terminals (speaker B) if your amplifier is so equipped. Refer to
Figure A. Alternately, you can connect the wires from your main speakers, along with the sub-
woofer’s input wires, to the “SPEAKER IN” terminals on the subwoofer. This may be more conve-
nient if the subwoofer is closer to your speakers than it is to your electronics. Please consult your
dealer for details regarding connection of multiple speaker cables to a common set of speaker out-
puts. For optimal performance, use equal lengths (left and right inputs) of the same high quality
speaker cable that you are using to connect your main speakers. Consult your Klipsch dealer for
recommendations. Refer to “About Speaker Wire Connections” for more detail.
“S P EAKER OUT” / KS W 1 2 AND 1 5
If a bass limited signal (high pass filtered) is being sent to your main speakers, connect them to the
“SPEAKER OUT” terminals on the subwoofer instead of to your amplifier. Refer to the righthand
side of Figure B. The high pass filter on these outputs will remove the bass frequencies below 100Hz
from your main speakers, lowering distortion and increasing their dynamic range. Also refer to the
“LOW PASS” section for more detail.
Note: Do not connect another subwoofer to these outputs as they are high pass filtered (bass
frequencies removed).
ABOUT S P EAKER W IRE CONNECTIONS
!
When making any type of speaker wire connection be sure to observe proper polarity (+ to + and -
to -). If the polarity of one of the subwoofer input wires is reversed, the output of the subwoofer will
be diminished. Most speaker wire is color-coded or has some distinguishing feature differentiating
the two conductors. Speaker wire connectors on most loudspeakers and amplifiers are also color-
coded. Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter which
wire conductor is connected to the positive or negative connection of your equipment as long as you
are consistent. Be sure that the connections from the amp to all of the speakers in your system are
connected in a like manner. If this is not done, the quantity of bass will be reduced and the stereo
image will be compromised. Be careful to avoid excess bare wire or loose strands of wire at the con-
nections. This could cause a shorting condition between adjacent positive and negative terminals,
damaging your speakers and amplifier.
LINE LEVEL CONNECTIONS
These connections should be made using high quality shielded interconnect cables terminated with
RCA phono plugs. These cables should be as short as possible and kept away from noise generating
electrical equipment such as digital electronics or electric motors. Consult your Klipsch dealer for
specific cable recommendations.
“LINE IN” / ALL M ODELS
For best results, these jacks should be connected to a non-filtered (full-range) subwoofer or main
channel pre-amp output on your receiver or pre-amp/processor. Refer to the lefthand side of Figure B.
This input signal should contain the normal bass information present in the main left and right chan-
nels. When connecting to a component that has only a single pair of pre-amp outputs, “Y” adapters
(splitters) may be used to feed a signal to both the subwoofer and the power amplifier.
“LINE IN” / KS W 1 0 a nd 1 2 ONLY
You can connect a mono subwoofer output on your electronics to the “L/LFE” input using a single
interconnect cable. If there is an inadequate amount of subwoofer volume even with the level control
set to maximum, add a “Y” cord to the subwoofer end of the cable and connect to both line inputs.
This will provide a significant (6dB) increase in the subwoofer’s output level.
“LINE OUT” / KS W 1 5 ONLY
If a bass limited (high pass filtered) signal is to be sent to your main speakers, connect the “LINE
OUT” jacks on the subwoofer to the line level inputs on your main channel power amplifier.
Figur e B
KS W 1 2
INP UT P ANEL
• Speaker Level Connections at Right / Main Speakers Limited Range
• Line Level Connections at Left / Main Speakers Full Range
• Optional LFE Connection, Compatible with Speaker and Line Level
Hookups —— - - ——
• One Channel Shown / Repeat for Opposite Channel
Figur e C
KS W 1 5
INP UT P ANEL
• Line Level Connections / Main Speakers Bass Filtered
• Optional LFE Connection, Compatible with Speaker and Line Level
Hookups —— - - ——
• One Channel Shown / Repeat for Opposite Channel
S ubwoofer P la cem ent
Your Klipsch subwoofer is designed to operate at frequencies below 120Hz, which are essentially
omnidirectional (difficult to localize). There may be several options for placement of the subwoofer in
your room that will effect its frequency response and output level. Corner placement improves the
acoustic loading of the subwoofer, increasing its output and dynamic range capabilities. Placing the
subwoofer away from walls or in the center of the room will result in the least amount of output.
Asymmetrical placement of two subwoofers in a room may improve low frequency reproduction by
providing a smoother and more consistent response pattern. Since even minor repositioning will result
in an audible performance change due to room acoustics, Klipsch recommends experimentation with
the subwoofer placement in the room.
A general rule of thumb is to place your subwoofer in the vicinity of the speakers with which it is
being paired. For example, a subwoofer reproducing front channel bass will generally perform better
when placed in the same end of the room as the main speakers. As well, a subwoofer connected to
the rear channels of a surround system performs best when positioned in the rear of the room.
If the subwoofer is installed near your television and color distortion is noted, simply move the sub-
woofer farther away from your television until the interference disappears.
If your subwoofer is placed in an enclosed cabinet, provisions must be made to ventilate the heat
radiated by the enclosed amplifier. Additionally, since some of the acoustic output is generated by the
sub’s rear firing port, a minimum of several inches of space should be provided around the sub-
woofer. If the front of the cabinet is acoustically open, the back of the subwoofer, with the port and
amplifier controls, should be oriented in this direction.
If your subwoofer will be used on a hard, non-carpeted surface, attach the enclosed rubber pads to
the subwoofer’s feet to prevent vibration and marring.
How t o Connect Your
KS W S er ies S ubwoofer
AC P ower
Since your KSW subwoofer has an internal power amplifier, it must be plugged into a nearby AC wall
outlet. The subwoofer should be unplugged from the AC power with the power switch in the OFF posi-
tion during hookup and installation. To eliminate a tripping hazard, all connections should be
unplugged from the back panel of the subwoofer if it is being moved. Avoid extremely long extension
cords of small gauge since they may impair the performance of the subwoofer amplifier and present a
potential fire hazard. If the subwoofer will not be used for an extended period of time, unplug the
power cord from the AC power outlet.
Note: 230 volt models are not supplied with an AC power cord, but are equipped with an IEC-type
power cord socket.
CAUTION: SINCE YOUR KLIPSCH SUBWOOFER HAS BUILT-IN ELECTRONICS, DO NOT
PLACE IT NEAR SOURCES OF HEAT OR MOISTURE! TAKE CARE TO ROUTE THE POWER
CORD SO THAT IT WILL NOT BE CUT, DAMAGED OR PINCHED.
!
Types of Connect ions
Your subwoofer may be installed using either the SPEAKER LEVEL or LINE LEVEL connection, but
not both. The LFE connection is an optional line level connection that can be used in conjunction
with either type of hookup. Refer to the “LFE IN / BYPASS IN” and “BASS MANAGEMENT” sec-
tions for more detail. You can connect the subwoofer so that your main speakers will reproduce a full
range signal (all models) or a limited range (bass filtered) signal (KSW 12 and KSW 15 only). Speaker
level connections are used when connecting to a receiver or integrated amplifier that lacks line level
subwoofer or pre-amp output jacks. Line level connections are often the best choice when connecting
the subwoofer to a system comprised of a separate pre-amp/processor and power amplifier. This also
applies to any receiver or integrated amplifier that possesses main channel pre-amp or subwoofer
outputs. The type of connection configuration used depends upon the capabilities of your equipment
and your performance goals.
Figur e A
KS W 1 0
INP UT P ANEL
• Speaker Level Connections / Main Speakers Full Range
• Optional LFE Connection, Compatible with Speaker and Line Level
Hookups ——— - - ———
• One Channel Shown / Repeat for Opposite Channel
Refer to Figure C. Depending upon the setting of the “HIGH PASS SELECT” switch, these outputs
will remove frequencies below 50Hz or 100Hz from your main speakers. This type of hookup cre-
ates a bi-amplified system, lowering distortion and increasing dynamic range.
“LFE IN”/ “BYP AS S IN” / KS W 1 5 ONLY
This input should ideally be connected to a low pass filtered LFE subwoofer output jack on your
electronics. Refer to Figure C. It is typically used with the newest 5.1 (six channel) surround sound
systems. Signals coming into this jack are not effected by the subwoofer’s adjustable “LOW PASS
(HZ)” filter. The “LFE IN”/ “BYPASS IN” input and “LINE IN” inputs are summed together so
both connections may be used concurrently if your electronics provide you with both outputs. The
“LFE IN”/“BYPASS IN” may also be used in conjunction with speaker level inputs.
BAS S M ANAGEM ENT
Most surround sound electronics are equipped with a bass management system that permits the
selection of either a full or limited range (filtered) operation for each speaker, including the sub-
woofer. When using either the subwoofer’s “LINE IN” or “SPEAKER IN” inputs, configure the main
channels of your surround processor for the “Large” or “Full Range” setting. If the subwoofer output
on your electronics has a “non-defeatable” low pass filter, set the “LOW PASS (HZ)” control on the
subwoofer to its highest setting (120Hz). The dedicated LFE input on the KSW 15 is the exception
to this rule. Refer to “LFE IN”/ “BYPASS IN” / KSW 15 ONLY.
The “.1” or LFE (Low Frequency Effects) channel contains a different signal than the bass frequencies
present in the other channels. This information can be up to 10 decibels louder than the bass signals in
the other channels, so caution should be exercised when connecting to this output and initially adjust-
ing the subwoofer's level control.
Oper a t ing Cont r ols
“LEVEL” / ALL M ODELS
The “LEVEL” control adjusts the volume of the subwoofer relative to your main speakers. Use this
control to compensate for room acoustics, subwoofer placement and the sensitivity of your main
speakers. This control effects the signals that are connected to any of the subwoofers inputs. It does
not effect the volume level of your main speakers.
Suggested control position for initial setup: 10 to 12 o' clock.
“LOW P AS S (HZ)” / ALL M ODELS
The “LOW PASS (HZ)” control is a variable filter that controls the upper frequency limit of the sub-
woofer. Use this control to compensate for room acoustics, subwoofer placement, type of hookup and
the capabilities of your main speakers. The filter is continuously variable from 40 to 120Hz. Proper
adjustment of this control helps smooth the transition in the bass frequencies between your main
speakers and the subwoofer. Setting the filter too high will cause an overlap in the bass frequencies
reproduced by your main speakers resulting in muddy and indistinct bass. Setting this control too low
may cause the output of the subwoofer to sound disconnected from the bass range being reproduced
by the main speakers. In light of this, we encourage you to experiment with various settings.
If your main speakers are being high pass filtered with an external filter, the “LOW PASS (HZ)”
control on the subwoofer should initially be set near the frequency of this filter.
In some cases, you may elect to feed your main speakers a full range signal. In these situations, the
“LOW PASS” control should be set near the low frequency limit of your main speakers (typically at
the lowest setting of the control with larger, full-range speakers). In all cases, experiment due to vari-
ability in speaker placement, room acoustics and associated equipment.
HIGH P AS S FILTERING, S P EAKER LEVEL / KS W 1 2 AND 1 5 ONLY
If your speakers are connected to the “SPEAKER OUT” terminals on the subwoofer, they are being
fed a bass limited (high pass filtered) signal. The “LOW PASS (HZ)” control should initially be set
near 100Hz.
“HIGH P AS S S ELECT” / KS W 1 5 ONLY
This switch selects either “50Hz” or “100Hz” as the bass cutoff frequency for your main speakers
when using line level connections. Refer to Figure C. This requires that your KSW 15 be connected to
a system utilizing both the preamp output and the power amp input jacks. Typically, the higher
“100Hz” setting is used for smaller bookshelf speakers to relieve them of the strain of reproducing
loud, deep bass frequencies. The “50Hz” setting is typically selected for larger floorstanding speakers
as they are better able to handle bass energy, needing reinforcement only at the lowest frequencies.
The subwoofer’s high pass filter has a gentle cutoff so there is still some audible signal content in
your main speakers below the circuit’s cutoff frequency.
“P OW ER” / ALL M ODELS
This switch has conventional power “ON” and “OFF” positions, as well as an automatic setting. In
the “AUTO” position, the subwoofer will turn itself on when it receives a signal from your system.
If no signal is sent for a period of 15 minutes, the sub will turn itself off. A red power light indicates
a standby mode in which the amplifier will turn on when it senses a signal. Green indicates the sub-
woofer is on and receiving a signal.
“P HAS E” / ALL M ODELS
This switch is used to reverse the polarity (phase) of the subwoofer relative to your main speakers,
allowing you to compensate for any acoustic cancellation of bass energy caused by the listening
room. Audition a recording with a prominent, repetitive bass line in your listening chair. Use the set-
ting that yields the greatest quantity of bass (0 or 180). The proper setting of this control is affected
by room acoustics and the placement of the subwoofer in the room. You may need to repeat this
procedure if the subwoofer is repositioned.
Tr oubles hoot ing
• If your subwoofer has little or no output:
— Double check your power (AC) and system connections.
— Make sure that the “LEVEL” control is turned up.
— Make sure that the “POWER” switch on the rear control panel is in the “ON” or
“AUTO” position.
— Ensure that the “POWER” light on the front of the cabinet is lit. If it is not, check the AC
fuse. When changing the AC main’s power fuse, unplug the power cord first. To access the
fuse, use the appropriate screwdriver to unscrew the flush cap on the amplifier’s fuse receptacle.
If the fuse is blown (the filament inside the glass tube is burned through), replace it with the
same type and value printed on the amplifier panel next to the fuse holder. NEVER INSTALL
A LARGER FUSE THAN THE VALUE INDICATED ON THE AMPLIFIER PANEL. If the
fuse blows again when the subwoofer is powered up, return the unit to your authorized
Klipsch dealer for servicing by qualified personnel. If dealer service is not available, contact
Klipsch customer service for a Return Authorization number before shipping (REQUIRED).
Klipsch Customer Service: 800-554-7724
All return shipments should be made to:
Klipsch, L.L.C.
137 County Road #278
Hope, AR 71801
RA#…(return authorization number required)
•
All KSW powered subwoofer amplifiers are protected by a thermal sensor. If they run for extended
periods beyond their designated power rating, the thermal sensor will engage and shut down the
subwoofer. If this occurs, turn the “POWER” switch off, reduce the volume level on your electronics
and wait five minutes before restarting the system.
•
•
If the “HI LEVEL” connections are in use, a polarity reversal of one of the speaker wires coming
from your amplifier will result in diminished output from the subwoofer. Refer to “About
Speaker Wire Connections.”
If you experience a noticeable hum when the subwoofer is connected to your system, and if your
system includes video equipment, disconnect the cable television line (if present) from the system.
If the hum disappears, consult your Klipsch dealer for a ground isolator for the cable line. If this
does not solve the problem, contact your Klipsch dealer for further advise.
•
•
If you connect the subwoofer to a second set of speaker terminals (i.e. speaker B), and there is a
dramatic loss of volume from your main speakers, hook the subwoofer to the same terminals as
your main speakers on your amplifier. Alternately, you can hook your main speakers to the
“SPEAKER IN” terminals on the subwoofer, along with the subwoofer’s input cables, or switch
to a line level connection if your electronics permit. If you are still experiencing difficulties, con-
sult your authorized Klipsch dealer.
Regardless of your amplifier’s rated capacity, do not operate the system at the full output (highest
volume): Amplifiers can create extremely high levels of distortion when operated at full output
and can damage your loudspeakers.
If you have any questions regarding the installation or connection of your subwoofer, please contact
your Klipsch dealer or contact us directly at 800-554-7724.
Ca r e a nd Clea ning of Your S ubwoofer
Your KSW Series subwoofer has a durable matte vinyl finish that should require only dry dusting or
cleaning with a damp cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents.
|