©
Assembly Instructions
„SCOOTER PRINCESS“
# 08451-799
USA
Adult Assembly Required
Tools required for adult Not included:
assembly (included):
picture similar
®
KETTLER International Inc. · 1355 London Bridge Road · Virginia Beach VA 23453
I This product is suitable for children between 3 – 6 years with a body height from 35 – 45
inches.
!
I
CAUTION: This package contains small parts which, before assembly, present hazar-
dous sharp edges or points and/or a potential choking hazard to children under the age
of three. Care should be taken during unpacking and assembly to ensure that all small
parts are accounted for and kept out of the reach of children.
Use of the Toy
I WARNING: Adult supervision is required. Never use near steps, slopes, driveways, hills,
roadways, alleys or swimming pool areas. Always wear shoes. Never allow more than
one rider (without a tandem seat). The use of protective gear and a Safety Helmet is high-
ly recommended.
I Ensure that the toy vehicle is not used until it has been properly assembled and checked
by an adult person.
I Do not transport any objects on the scooter.
I Always adjust the use of the scooter to the conditions encountered.
I Scooters do not possess a continuously effective brake system. Therefore, safeguard the
scooter against rolling away
I Instruct your child how to use the vehicle correctly and draw attention to possible sources
of danger.
I Although dangerous situations are unlikely to occur if the toy is used correctly, children at
play should, if possible, be supervised.
I Please bear in mind that there is always a danger of children injuring themselves while
using swings, climbing frames,toy vehicles or similar equipment.
I When using the toy vehicle, the user should always wear strong closed toe shoes.
I When children are at play, situations may arise which cannot be predicted by the manu-
facturer and for which he cannot be held responsible.
I Before use, always check all screws and plug-in connections as well as respective safety
devices fit correctly.
I Never use corrosive or abrasive substances to clean the toy. Never use substances which
may cause pollution of the environment.
I Lubricate the bearing sleeves of the wheels and the handlebars with a few drops of oil eve-
ry two or three months.
Assembly of the toy vehicle
I The toy vehicle must be assembled carefully by an adult person. Study the assembly instruc-
tions carefully before beginning work. Assemble the vehicle in the exact sequence shown by
the letters in the diagrams. This is essential for the safe function and use of the scooter.
3
I Please note that there is always a danger of injury when working with tools or doing
manual work. Therefore please be careful when assembling this scooter.
I Ensure that your working area is free of possible sources of danger, for example don’t
leave any tools lying around. Always dispose packaging material in such a way that it
may not cause any danger. There is always a risk of suffocation if children play with
plastic bags!
I Bolt all the parts together loosely at first, and check that they have been assembled cor-
rectly. Tighten the locknuts by hand until resistance is felt, then use wrench to finally
tighten nuts completely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once locknuts have been un-
screwed they no longer function correctly (the locking device is destroyed), and must
be replaced.
I The grips can be pushed onto the handlebars more easily if they are first soaked in warm
water.
I Please keep original packaging of this article, so that it may be used for transport at a lat-
er date, if necessary. Goods may only be returned after prior arrangement and in (inter-
nal) packaging, which is safe for transportation, in the original box if possible. It is im-
portant to provide a detailed defect description / damage report!
I For technical reasons, we reserve the right to carry out preliminary assembly work (e.g.
addition of tubing plugs).
I When ordering spare parts, always state the full item number, spare-part number, the
quantity required and the serial number of the product.
Example order: item # 08451-799 / spare part no. 12802003 / 1 piece/ S/N ...
Important: spare part prices do not include fastening material; if fastening material (bolts,
nuts, washers etc.)
is required, this should be clearly stated on the
order by adding the words „with fastening material“.
®
KETTLER limited warranty
THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR
OR THE MANUFACTURER ON KETTLER PRODUCTS, EXCEPT THE MANUFACTURER’S LIMITED
WARRANTY AGAINST DEFECTS IN MATERIAL SET OUT BELOW:
This KETTLER® Limited Warranty applies to products sold through the KETTLER® Authorized De-
aler Network to the original retail purchaser and authenticated by proof of purchase from a re-
tailer located in the United States. Any shipments made under this warranty will be shipped to
the United States only. Any shipment outside of the United States will be at the sole cost of the
customer. This KETTLER® Limited Warranty is a manufacturer’s warranty and is not changed or
modified by additional warranties extended by individual retailers at the point of sale. Manu-
facturer warrants this product to be free from defects in material at the time of the product’s ten-
der of delivery for a period of 3 years for residential use. This Limited Warranty is not transfe-
rable and does not cover normal wear and tear (including, but not limited to, damage and wear
4
to tires, power shocks, drive belts and other non-durable parts). The liability of the manufactu-
rer under this Limited Warranty shall not include any liability for direct, indirect, or consequen-
tial damages resulting from the defect. This Limited Warranty is void if the product is damaged
by accident, unreasonable use, improper service, failure to follow instructions provided, modi-
fication from its original state, or other causes determined not arising out of defects in material.
This warranty gives you specific legal rights. Should this product become defective due to ma-
terial within the warranty period, contact KETTLER® Parts & Service Dept. by phone at
866.804.0440, fax at 757.563.9273, or e-mail at [email protected].
THIS LIMTIED WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON THE PART
OF THE MANUFACTURER. KETTLER® NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH SUCH PRO-
DUCTS.
®
KETTLER International Inc., 1355 London Bridge Road · Virginia Beach VA 23453
For parts or service ONLY call 1-866-804-0440 or send e-mail to:
call (866) 804-0440 fax (757) 563-9273.
The manufacturer reserves the right to make changes reflecting product or
other technical advances. The content of these instructions is accurate at the
date of printing.
5
Checklist
1/1
1
1
1
1
1
1
M8x40
M8
1
2
1
1
3,9x16
1
6
1
3
2
C
B
A
4b
4a
7
5
6
A
A
B
M12
8
Handling
B
USA
HEINZ KETTLER GmbH & Co. KG
D-59463 Ense-Parsit
C
Art.-Nr. 08718-000
Serien-Nr.: 1-344 O-1801 0001
geprüft nach DIN EN 71-1, -2, -3
A
Made in Germany
9
Spare parts drawing
19
19
14
18
20
17
15
16
2
7
5
13
4
6
3
8
1
2
9
10
11
12
10
Spare parts list 08451-799
no. description
qty.
spare part no.
1
2
3
4
5
6
7
8
9
frame (complete)
frame bushings (3247)
plug 35x41mm
brakeplate
1
2
1
1
1
1
1
2
1
2
1
2
1
1
1
1
1
1
91611406
70121718
70113610
97200263
25716925
25024005
70121727
10116061
91620372
10122155
15170300
70121883
70121728
97100398
91650357
11500007
70121753
91670081
brake spring
brake
foot plate (3355)
rear wheel
wheel fork
10 wheel bearing
11 front wheel with caps
12 wheel covers
13 fender (3336)
14 handle bar
15 reducing tube
16 clamp
17 covering, left
18 quick release knob M12
19 grip
20 covering, right
21 hardware bag w/o fig.
2
1
1
10111037
70121752
91680500
11
docu 2392/12.08
|