Kenwood Stereo Receiver KRC 279RA User Manual

CASSETTE RECEIVER

KRC-279RA

KRC-279RG

KRC-179RA

KRC-179RG

KRC-25RA

KRC-25RG

KRC-15RG

INSTRUCTION MANUAL

B64-1854-00 (EN)

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not set the removed faceplate or the

faceplate case in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.

• To prevent deterioration, do not touch the

terminals of the unit or faceplate with your

fingers.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the LCD

is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

— 3 —

Safety precautions

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

Cleaning the Tape Head

NOTE

After you have used the tape player many

times over a long period, magnetic powder

from the tapes and dust accumulates on the

tape head, causing noise and a deterioration

in sound quality. Clean the tape head using a

cleaning tape or cleaning kit designed for use

in car audio systems.

• If you experience problems during

installation, consult your Kenwood dealer.

• If the unit does not seem to be working right,

try pressing the reset button first. If that does

not solve the problem, consult your Kenwood

dealer.

Egnlish

Cleaning the Unit

If the faceplate of this unit is stained, wipe it

with a dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the

stain off with a cloth moistened with neutral

cleaner, then wipe neutral detergent off.

SRC

REW FF

Handling Cassette Tapes

CLK

40Wx 4

HIGH POWER

• Do not play a cassette whose tape has gone

slack. In such a case, wind it tight using a

pencil or the like in one of the spools. Playing

slack cassette tapes can result in the tape

tangling around the capstan and/or pinch

rollers, causing trouble.

• Do not play a deformed cassette or one

whose label is starting to come off, as it can

cause the unit to malfunction.

• Do not leave tapes in hot places, such as

above the fascia panel (dashboard) and other

spots exposed to direct sunlight, or near

heater outlets. They can deform the cassette.

• Avoid using extremely long cassette tapes,

such as 100-minute-long tapes. Such tapes

are very thin, and can tangle easily around

the pinch rollers or other parts inside the unit,

causing unit failure.

2CAUTION

AUD

ATT

Applying spray cleaner directly to the unit

may affect its mechanical parts. Wiping the

faceplate with a hard cloth or using a volatile

liquid such as thinner or alcohol may scratch

the surface or erases characters.

Reset button

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

• Remove a cassette tape from the unit when

not listening to it for a whilst. If you leave a

tape in the unit too long, it may stick to the

tape head and cause unit malfunction.

— 4 —

General features

Power

Release button

Turning on the power:

SRC /

PWR OFF

Press the SRC button.

NOTE

Turn the power on before carrying out the following procedures.

Turning off the power:

SRC

REW FF

PR OG

Hold down the PWR OFF button for one second or more.

CLK

40Wx 4

HIGH POWER

AUD

ATT

Volume

Increasing Volume:

AUD

#1 ~ 5

Press the u button to turn up the volume.

ATT / LOUD

Decreasing Volume:

Press the d button to turn down the volume.

ATT indicator

Attenuator

This function allows you to turn down the volume quickly.

Turning Attenuator On/Off:

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

LOUD indicator

NOTE

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

— 5 —

General features

Switching Modes

Loudness

This function amplifies low and high tones when the volume is

Switching Modes:

turned down.

Each time you press the SRC button, the mode switches as

follows:

The LOUD indicator lights up, when the loudness function is

on.

Egnlish

▼

Turning Loudness On/Off:

Tuner mode

▼

Hold down the LOUD button for one second or more to switch

the loudness on and off.

Tape mode

▼

External disc control mode 1

(KRC-279RA/279RG/25RA/25RG only)

▼

External disc control mode 2/AUX mode

(KRC-279RA/279RG/25RA/25RG only)

S^▼tandby mode

Audio Control Setting

Adjust various parameters of sound quality.

Selecting the standby mode:

Press the AUD button to enter the control mode.

• Press the SRC button repeatedly to select to "ALL OFF" .

When "ALL OFF" is displayed, the standby mode is turned on.

The standby mode turns all functions off although leaving the

unit’s power on. Use this mode when you want to have the

display illuminated but do not want to listen to anything.

• If you have selected Standby mode, the timer function that

turns the power OFF automatically will be activated.

To find out how to set the time on the timer, and how to cancel

the timer function, refer to the section on the Power OFF Timer

function under Menu Settings (page 21).

Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the adjustment

modes.

NOTE

Source tone memory

Each source (tape, FM, AM, and disc changer) has its own

memory in which to store the bass and treble tone settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or

KDC-CX82) is connected to this unit.

Adjust each mode

Press the 4/¢ button.

Please refer to the following for the adjusting values.

Press the AUD button to end the control mode.

During the AUX mode, "AUX" will show in the display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

— 6 —

TEL Mute

"DB" : Recalling the kenwood preset sound setting

Press the preset buttons (#1-5).

Shut down the audio system temporarily whenever an

incoming call is received.

Settings: #1;FLAT, #2;ROCK, #3;POPS, #4;JAZZ, #5;EASY

NOTE

You can call the following settings with this function; bass

centre frequency, bass level, bass quality factor, bass extension,

treble centre frequency, and treble level setting.

The function will not work if a cable is not connected to the car

phone.

When the telephone rings:

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Restoring Original Unit Source During Phone Call:

Press the SRC button.

"BAS" : Adjust the bass level.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Setting values: - 8 – + 8

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

"TRE" : Adjust the treble level.

Setting values: - 8 – + 8

"BAL" : Adjust the balance level.

Setting values: Left 15 – Right 15

"FAD" : Adjust the fader level.

Setting values: Front 15 – Rear 15

— 7 —

General features

Tuner features

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you,

helping to deter theft.

CLK

SRC

Egnlish

SRC

REW FF

PR OG

Projections

CLK

Release button

40Wx 4

HIGH POWER

Grooves

AUD

ATT

Removing Faceplate:

Press the release button.

The faceplate is unlocked, allowing you to detach it.

#1 ~ 6

NOTE

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

AUTO indicator

ST indicator

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

Frequency

Preset station number

Reattaching Faceplate:

Band display

Align the projections on the unit with the grooves on the

faceplate.

Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

— 8 —

Tuning

Select the band/ station that you want to have stored.

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

Press the SRC button repeatedly until the tuner mode is

obtained. "TUNER" is displayed only when the tuner mode is

selected.

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Press the AM button to select the MW and LW bands.

NOTE

• Auto Seek Tuning

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

Clock display

NOTE

Turning clock display On/Off:

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station seek

will receive channel 1.

Each time you press the CLK button, the display switches

between the Programme Service name (during RDS station

reception) and clock.

Displaying Frequencies:

Hold down the CLK button for two seconds or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

NOTE

• The ST indicator lights up when stereo broadcasts are being

received.

• Please see the menu settings about selecting tuning mode.

(page22)

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

— 9 —

RDS features

RDS (Radio Data System)

SRC

CLK

RDS is a digital information system that lets you receive signals

besides those of regular radio programmes, such as network

information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency with

the best reception for the particular network of stations that

you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

TI / VOL ADJ

FM / PTY

Egnlish

SRC

REW FF

PR OG

CLK

40Wx 4

HIGH POWER

AUD

ATT

Enhanced Other Network

Stations that offer <Enhanced Other Network> also transmit

information about other RDS stations that have traffic

information. When you are tuned to a station that is not

transmitting traffic information, but another RDS station starts

transmitting a traffic bulletin, the tuner automatically switches

to the other station for the duration of the bulletin.

PTY indicator

TI indicator

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 10 —

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

Hold down the TI VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

When a traffic bulletin begins to be broadcast, "TRAFFIC" will

be displayed, and reception will begin at the preset volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

NOTE

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

NOTE

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides <Enhanced Other Network>

services, you can still have traffic information received.

• Holding the TI button down for one second or more when the TI

function is on in the disc control mode results in a change to the

frequency display of the traffic information station for five

seconds.

— 11 —

RDS features

17. Finance

(FINANCE)

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

18. Children’s programmes (CHILDREN)

19. Social Affairs

20. Religion

(SOCIAL A)

(RELIGION)

(PHONE IN)

(TRAVEL)

(LEISURE)

(JAZZ)

(COUNTRY)

(NATION M)

(OLDIES)

(FOLK M)

(DOCUMENT)

(MUSIC)

Egnlish

21. Phone In

Hold down the PTY button for one second or more.

The PTY indicator will turn on, and the Programme Type

Selection (PTY) Mode entered.

If you make no key input in 30 seconds, the mode will

automatically turn off.

22. Travel

23. Leisure

24. Jazz Music

25. Country Music

26. National Music

27. Oldies Music

28. Folk Music

29. Documentary

Music

NOTE

You cannot use this function whilst the traffic information

function is turned on.

NOTE

Changing the Display Language to French or German

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

In the PTY mode, hold down the CLK button for one second or

more to display the name of the language currently used.

If you want to change the language, press the preset button for

the desired language and then the CLK button.

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

English is #1, French is #2, and German is #3.

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

NOTE

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the new

programme type is stored.

The selection includes:

Speech

(SPEECH)

(NEWS)

1. News

Seeking the selected programme type

2. Current Affairs

3. Information

4. Sports

(AFFAIRS)

(INFO)

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

The display blinks and the seek starts.

(SPORT)

5. Education

6. Drama

(EDUCATE)

(DRAMA)

(CULTURE)

(SCIENCE)

(VARIED)

(POP M)

If your selected type of programme is found, the name of the

station is displayed and the station is tuned into.

"PTY" blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

7. Culture

8. Science

9. Varied

10. Pop Music

11. Rock Music

12. Easy Listening Music

13. Light Classical

14. Serious Classical

15. Other Music

16. Weather

(ROCK M)

(EASY M)

(LIGHT M)

(CLASSICS)

(OTHER M)

(WEATHER)

NOTE

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

Switching to Other Stations with the Same Type of Programme:

— 12 —

Cassette player features

When "PTY" is blinking in the display, perform auto seek tuning.

The tuner scans for another station with the same type of

programme.

SRC

REW FF

Cancelling Programme Type Function During Its Operation:

Hold down the PTY button for one second or more.

SRC

REW FF

CLK

40Wx 4

HIGH POWER

AUD

ATT

T.C ( T.CALL )

Tape indicator

— 13 —

Cassette player features

Playing Cassette Tapes

Tuner Call

Switch automatically to the tuner whilst you are rewinding or

fast forwarding the tape.

Loading and Playing Cassettes:

Load a cassette with the tape exposed on the right.

The tape starts playing automatically.

Egnlish

Turning Tuner Call Function On/Off:

Press the T.C(T.CALL) button to switch the tuner call function

on and off.

With Side A facing up, the 3 indicator lights up when Side A is

playing, and 2 when Side B is playing.

Playing Cassettes Already Loaded:

Press the SRC button repeatedly until tape mode is obtained.

"TAPE" is displayed when the tape mode has been selected.

Listening to the other side:

Press the FF button and REW button at the same time.

Tape play switches to the other side.

Stopping and Ejecting Cassettes:

Press the 0 button.

The tape stops playing and the cassette ejects.

NOTE

Remove a cassette from the unit when not listening to it for a

whilst. If you leave it in the unit too long, the tape may stick to

the tape head and cause the unit to malfunction.

Fast Forwarding and Rewinding Cassette Tapes

Fast Forwarding Tapes:

Press the FF button.

The tape indicator blinks in the direction of the tape as it is

being fast forwarded.

If the REW button is pressed, normal tape play returns.

Rewinding Tapes:

Press the REW button.

The tape indicator blinks in the direction of the tape as it is

being rewound.

If the FF button is pressed, normal tape play returns.

— 14 —

External disc control features

Function of the KRC-279RA/279RG/25RA/25RG

■ When a unit equipped with an O-N switch is to be connected,

please also see the instruction manual of this unit.

Set the O-N switch to "N". "N"-operation will be set.

NAME SET / CLK

DISC+

SRC

"N"-operation:

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

SRC

REW FF

PR OG

CLK

40Wx 4

HIGH POWER

"O"-operation:

• CD text cannot be displayed.

AUD

ATT

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, *, =, <, >, [ , ]".

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

REP

M.RDM

SCAN

DISC-

RDM

D.SCN

Track number

Disc indicator

Disc number

Track time

— 15 —

External disc control features

Function of the KRC-279RA/279RG/25RA/25RG

Playing Disc mode

This funciton permits the connection of optional players and

the playing of discs.

Track Search

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

Egnlish

Playing Discs:

Making a Reverse Track Search:

Press the SRC button repeatedly to select the external disc

control mode.

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current track,

twice to search back to the beginning of the previous track, and

so forth.

The disc will start playing.

NOTE

Play starts at the beginning of the displayed track number.

NOTE

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "CD" ...when a CD player is connected

• "DISC" ...when a disc changer is connected

• "DISC-1" , "DISC-2" ...when two disc changers are connected

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Making a Forward Track Search:

NOTE

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

• When one disc has finished playing its last track, the next disc in

the changer starts playing. When the last disc in the changer

has finished, the player returns to the first disc and starts

playing it.

Play starts at the beginning of the displayed track number.

NOTE

• Disc #10 is displayed as "0".

You cannot make a forward track search when listening to the last

track on a disc.

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Disc Search

(Function of disc changers)

Reversing Disc Play:

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

Hold down on the 4 button.

Release your finger to play the disc at the point.

NOTE

Making a Reverse Disc Search:

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which point

normal play automatically resumes.

Play starts at the beginning of the displayed disc.

— 16 —

Making a Forward Disc Search:

Starting the Track Scan:

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

Press the SCAN button. "TSCN/SCAN ON" is displayed and the

first 10 seconds of each track are played, and the tracks are

played in order.

Play starts at the beginning of the displayed disc.

The track number currently being heard blinks in the display.

NOTE

Stopping to Listen to the Track Being Scanned:

Press the SCAN button again to stop the scan and keep on

listening to a track normally.

"LOAD" is displayed when discs are being exchanged on the disc

changer.

NOTE

• The track scan function is cancelled when you eject the disc.

• The track scan function only scans each track on a disc once.

Track / Disc Repeat

Repeat playing the current track or disc.

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

Disc Scan

(Function of disc changers)

Successively play the beginning of each disc on a changer until

you find the one that you want to listen to.

▼

Track Repeat ON

▼

Starting the disc scan:

Disc Repeat ON (Function of disc changers)

Press the D.SCN button. "DSCN ON" is displayed and the first

10 seconds of each disc are played, in the order in which they

are loaded on the changer.

▼

Track/Disc Repeat OFF

The disc number currently being heard blinks in the display.

"TREP/REP ON" is displayed and the track number blinks in the

display when track repeat is on.

"DREP ON" is displayed and the disc number blinks in the

display when disc repeat is on.

Stopping to Listen to the Disc Being Scanned:

Press the D.SCN button again to stop the scan and keep on

listening to the disc normally.

NOTE

Repeat play is cancelled when you eject the disc.

• The disc scan function is cancelled when you eject the disc.

• The disc scan function only scans each disc on the changer

once.

• "LOAD" is displayed when discs are being exchanged on the disc

changer.

Track Scan

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

— 17 —

External disc control features

Function of the KRC-279RA/279RG/25RA/25RG

NOTE

Random Play

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

Play all the tracks on the current disc in random order.

Press the RDM button to switch the random play function on

and off.

Egnlish

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

"RDM ON" is displayed when random play is turned on.

The display of the track number changes continuously as the

next track is being selected.

NOTE

• Magazine random play is cancelled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

NOTE

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

To change the track being heard, press the ¢ button.

Text Scroll

Another track is selected and played.

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

NOTE

Random play is cancelled when you eject the disc.

To scroll manually:

Press the CLK button to display the disc title or the track title.

Holding down the CLK button for one second or more results in

one scrolling display of the titles.

To scroll automatically:

Magazine Random Play

Play the tracks on all the discs in the disc changer in random

order.

(Function of disc changers)

Press the CLK button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

NOTE

Press the M.RDM button to switch the magazine random play

function on and off.

When the disc or track to be played changes, the title is displayed

in one scrolling display.

"MRDM ON" is displayed when magazine random play is turned

on.

Holding down the CLK button for one second or more results in

one scrolling display of the titles.

The display of the disc and track numbers change continuously

as the next track is being selected.

NOTE

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

• Please see the menu settings (page 23) about switching

between manual scrolling and automatic scrolling.

• Only units with a CD text feature permit title display.

— 18 —

cancelled.

Presetting Disc Names

Store the names of discs to be displayed when played.

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

NOTE

Play the disc whose name you want to preset.

• The number of characters and discs whose names can be

stored will differ depending on the disc changer that is

connected. Please see your disc changer manual for details.

• Discs are identified by their total length and number of tracks.

If another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Pressing the reset button does not erase the disc names stored

in a disc changer.

NOTE

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track titles

for MDs that you record.

Hold down the NAME.SET button for two seconds or more.

"NAME SET" is displayed and the disc name preset mode is

entered.

The cursor blinks in the position where character input can be

made.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The 4 button moves the cursor to the left, and the ¢

button to the right.

^{Press the DISC}+ or DISC– button to display the desired

character.

Characters that can be displayed are as follows.

Alphabet (upper case) : A ~ Z

Numerals and symbols : 0~9 @ " ‘ ` % & * + - = , . / \ < > [ ]

NOTE

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

Operations can be followed again from Step 2 at a time such

as this, and the characters to be input are selected using the

procedure described below.

^{Press the DISC}+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, *,

=, <, >, [ and ].

Continue steps 3 and 4 until all the characters are chosen for

the name.

Press the NAME.SET button.

The disc name is stored and the disc name preset mode is

— 19 —

Menu settings

Menu System

You can set the defaults for additional functions in the menu

mode.

Make a setting for each function, referring to the following

operations.

Egnlish

SRC

REW FF

PR OG

Enter the menu mode

CLK

40Wx 4

HIGH POWER

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

AUD

ATT

Selecting function to set

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

#1 ~ 6

Press the AM button to search through the functions backward.

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "BEEP ON" in the display.

AUTO indicator

NEWS indicator

mc indicator

Changing setting for currently displayed function

Press either the 4 or ¢ button.

The setting will change for each function.

Example: The setting of the touch sensor tone will switch from

on to off, and "BEEP OFF" is displayed.

™ indicator

Ending the menu mode

Press the MENU button.

NOTE

Make sure to end the menu mode when finished.

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function and

the Alarm function.

— 20 —

set the time manually if the automatic time adjustment function

is turned off. The factory default is automatic time adjustment.

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

Display and setting:

"SYNC ON" : Automatic time adjustment

"SYNC OFF" : Manual time adjustment

Display and setting:

"BEEP ON" : Beep setting is on.

"BEEP OFF" : Beep setting is off.

Adjusting Time Automatically:

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

NOTE

The beep sound is not output from the preout jacks.

NOTE

The time is not adjusted when the RDS station you are tuned to is

not transmitting a time signal. Choose another RDS station in

such a case.

Manual Time Adjustment

Adjust the time manually.

Power OFF Timer

NOTE

Set the time for the OFF Timer function activated when you

This adjustment is available only when the automatic time

adjustment is set to off.

selected Standby mode.

If the predefined time elapses, this unit's power is

automatically turned off.

Display and setting:

Select the display "CLK ADJ" during the selecting function in

the menu system.

Display and setting:

"OFF ___" :Power OFF Timer function is canceled.

"OFF 20M" :Unit's power goes OFF after 20 minutes.

"OFF 40M" :Unit's power goes OFF after 40 minutes.

"OFF 60M" :Unit's power goes OFF after 60 minutes.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Manual time adjustment mode.

The time display will blink.

NOTE

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

The factory default is "OFF 20M" .

• Adjusting the minutes

Press the ¢ button to advance the minutes, or press the

4 button to make the minutes go back.

Automatic Time Adjustment

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

— 21 —

Menu settings

Selecting Tuning Mode

You can choose from three tuning modes: auto seek, preset

station seek, and manual.

News Bulletin Function

with PTY News Timeout Setting

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the News

Bulletin function is on, the PTY News Timeout setting allows

you to set the interval during which further news interruption

cannot take place. You can adjust the PTY news interruption

period from 10 to 90 minutes for each journey.

Egnlish

Display and setting:

"AUTO 1" : Auto seek tuning mode

"AUTO 2" : Preset station seek tuning mode

"MANUAL" : Manual tuning mode

Display and setting:

"NEWS OFF/ 00M/ 10M/ 20M/ 30M/ 40M/ 50M/ 60M/ 70M/

80M/ 90M"

(M= minutes)

: When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed

and reception will begin at the preset volume.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

NOTE

• If you choose the "20M" setting, further news bulletins will not

be received for 20 minutes once the first news bulletin is

received.

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to <Enhanced Other

Network>-Network sending PTY-code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn off

the function.

Display and setting:

Select the display "A-MEMORY" during the selecting function in

the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

NOTE

Local Seek Function

With the local seek function turned on, auto seek tuning skips

stations with relatively poor reception.

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS capability)

are stored. RDS stations that have been preset for FM1 cannot

also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local traffic

information station frequency will be stored.

Display and setting:

"LO.S ON" : The local seek function is on.

"LO.S OFF" : The local seek function is off.

— 22 —

Cancelling Auto Memory Entry During Its Operation:

Press the MENU button whilst auto memory entry is taking

place to stop the process.

Auto TP Seek Function

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Display and setting:

"ATPS ON" : The Auto TP Seek Function is on.

If the traffic information station you are tuned to

experiences poor reception, this function

automatically seeks another TP station.

"ATPS OFF" : The Auto TP Seek Function is off.

AF (Alternative Frequency) Function

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The ™ indicator lights up when the AF function is turned

on.

Display and setting:

"AF ON" : The AF function is on.

"AF OFF" : The AF function is off.

NOTE

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

• When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF

function in such a case.

Display and setting:

"MONO ON" : The monaural reception is on.

"MONO OFF" : The monaural reception is off.

• The AF function can be turned on or off even when the standby

mode has been turned on. If the power is on, the AF function

tunes in to stations that offer good reception.

Function of the KRC-279RA/279RG/25RA/25RG

Text Scroll

This function permits the CD text and MD title to be scrolled

and the entire text to be displayed. Switching between manual

scrolling and automatic scrolling is permitted. The factory

default is manual scrolling.

Restricting RDS Region (Region Restrict Function)

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted.

Display and setting:

"SCL AUTO" : Automatic scrolling

"SCL MANU" : Manual scrolling

Display and setting:

"REG ON" : The Region Restrict Function is on.

"REG OFF" : The Region Restrict Function is off.

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

— 23 —

Accessories

External view

Number of items

2CAUTION

• If your car is not prepared for this special connection-system,

consult your Kenwood dealer.

..........................................1

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

..........................................2

..........................................1

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

2CAUTION

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part in

the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

— 24 —

Connecting Cables to Terminals

Connector Function Guide

KENWOOD disc changer control input

(KRC-279RA/279RG/25RA/25RG only)

Pin Numbers for

ISO Connectors

Cable Colour

Functions

Rear left output (White)

Rear right output (Red)

NOTE

External Power

Connector

To connect the Disc

changer, consult your

Disc changer manual.

A–4

A–5

A–7

A–8

Yellow

Blue/White

Red

Battery

Power Control

Ignition (ACC)

Earth (Ground)

Connection

Antenna Cord (ISO)

Black

FM/AM antenna input

Antenna Conversion Adaptor

(ISO–JASO) (Accessory3)

Speaker

Connector

B–1

Fuse (10A)

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

Wiring harness

(Accessory1)

B–2

B–3

B–4

B–5

B–6

B–7

B–8

TEL mute cable (Brown)

Connect to the terminal that is

grounded when either the

telephone rings or during

conversation.

TEL MUTE

Green/Black

Battery cable (Yellow)

Ignition cable (Red)

If no connections are

made, do not let the cable

come out from the tab.

Power control/ Motor

antenna control cable

(Blue/White)

Connect either to the power

control terminal when using

the optional power amplifier,

or to the antenna control

terminal in the vehicle.

A–7 Pin (Red)

P.CONT

ANT.CONT

A–4 Pin (Yellow)

Connector A

Connector B

— 25 —

Connecting Cables to Terminals

Installation

■

Installation

2WARNING

Connecting the ISO Connector (see p.25)

The pin arrangement for the ISO connectors depends on the type

of vehicle you drive. Make sure to make the proper connections

to prevent damage to the unit.

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Firewall or metal support

Screw (M4X8)

(commercially

available)

Egnlish

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow)

is connected to the constant power supply.

Unit

Vehicle

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve with

a screwdriver or

Ignition cable (Red)

Self-tapping

screw

(commercially

available)

similar utensil and

attach it in place.

Battery cable (Yellow)

A–4 Pin (Yellow)

Metal mounting

strap

(commercially

available)

2 The A-7 pin (red) of the vehicle's ISO connector is connected

to the constant power supply, and the A-4 pin (yellow) is

linked to the ignition.

NOTE

Unit

Vehicle

Make sure that the unit is installed securely in place. If the unit is

unstable, it may malfunction (eg, the sound may skip).

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-7 pin (red) of the vehicle's ISO connector is not

connected to anything, whilst the A-4 pin (yellow) is connected

to the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Connect to a power source that can be

turned on and off with the ignition key.

Ignition cable (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

— 26 —

Installation

■

Removing the hard rubber frame

Removing the Unit

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Engage the catch pins on the removal tool and remove the two

locks on the lower level.

Lower the frame and pull it forward as shown in the figure.

Remove the screw (M4´8) on the back panel.

Insert the two removal tools deeply into the slots on each side,

as shown.

Catch

Lock

Catch facing up

Screw (M4X8)

(commercially

available)

Accessory2 Removal tool

When the lower level is removed, remove the upper two

locations.

Lower the removal tool

toward the bottom, and pull

out the unit halfway whilst

pressing towards the

inside.

2CAUTION

Be careful to avoid injury from the catch pins on the removal tool.

NOTE

Pull the unit all the way out

with your hands, being

careful not to drop it.

The frame can be removed from the top side in the same

manner.

— 27 —

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace the

fuse with one having the same rating.

Egnlish

No ACC position on vehicle ignition.

Connect the same cable to the ignition as the battery cable.

If you have selected Standby

mode, the power will go OFF

automatically.

The Power Off Timer function has come into play.

If you do not want the power to go OFF automatically,

cancel the Power Off Timer function.

No sound can be heard, or the

volume is low.

The Attenuator function is turned on.

Turn off the Attenuator function.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring

harness correctly. See the section on "Connecting Cables

to Terminals".

The cassette tape is bad.

Try playing another cassette tape. If no problem is

experienced, the first tape was bad.

Tape has been inserted but

there is no sound/the unit will

not go into tape mode

The tape has not been inserted correctly in the unit.

Re-insert the tape.

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

The tape head is dirty.

Press the reset button on the unit (see page 4).

Clean the tape head, referring to the section on "Cleaning

the tape head" (see page 4).

The sound quality is poor or

distorted.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

Reconnect the speaker cables so that each output

terminal is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

— 28 —

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns on

even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

Pull the TEL mute cable away from the metal part of the

car.

External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on

the unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is very dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labelled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Try another disc instead.

The sound skips.

Something is touching the disc changer.

Remove whatever is touching it.

The CD is scratched or dirty.

If skipping happens at the same place when the car is

stopped, something is wrong with the CD. Clean the CD.

The display shows that the

changer is being played, but no

sound can be heard.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see page 4).

The specified track does not

play.

Random play or magazine random play has been selected.

Turn off the random play or magazine random play function.

Conduct finalization processing with CD recorder.

Cannot play CD-R or CD-RW

Finalization processing is not being conducted for CD-

R/CD-RW.

A non-compatible CD changer is being used to play the

CD-R/CD-RW.

Use a CD changer compatible with CD-R/CD-RW to play.

If the following situations, consult your nearest service centre:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected,

the AUX Mode is entered when switching modes.

— 29 —

Troubleshooting Guide

The following messages are displayed when certain problems are occurring in your system. Take the

recommended actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

]

Load the disc magazine properly.

No CD in the unit.

Egnlish

]

Insert the CD.

No disc has been loaded in the disc magazine.

NO DISC

E-04

]

Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

]

Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

]

Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

No tracks are recorded on the MD, although it has a title.

The faceplate of the slave unit being connected to this unit has been removed.

NO TRACK

NO PANEL

]

Replace it.

The unit is malfunctioning for some reason.

E-77

E-99

]

Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

]

Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

stopping all operation.

HOLD

]

Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),

the disc starts playing again.

— 30 —

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (50 kHz Space)...............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N = 26dB)..................................0.7 µV/75 ½

Quieting Sensitivity (S/N = 46dB) ...............................1.6 µV/75 ½

Frequency response ( 3.0 dB) ..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO) ..............................................65 dB

Selectivity (DIN) ( 400 kHz)............................................. ³ 80 dB

Stereo separation (1 kHz).....................................................35 dB

Maximum output power .................................................40 W ´ 4

Output power (DIN 45324, +B=14.4 V) ..........................26 W ´ 4

Tone action

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / load...............................................1800 mV / 10 k½

Preout Impedance............................................................² 600 ½

MW tuner section

General

Frequency range (9 kHz Space)......................531 kHz – 1611 kHz

Usable sensitivity (S/N = 20dB)............................................25 µV

Operating voltage..............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W ´ H ´ D) ...........................182 ´ 53 ´ 155 mm

Weight................................................................................1400g

LW tuner section

Frequency range..............................................153 kHz – 281 kHz

Usable sensitivity (S/N = 20dB)............................................45 µV

Cassette player section

Tape speed...............................................................4.76 cm/sec.

Wow & Flutter (WRMS).....................................................0.12 %

Frequency response

(120 µs)...........................................30 Hz – 14 kHz ( 3 dB)

Separation (1 kHz) ...............................................................40 dB

Signal to Noise ratio ............................................................52 dB

— 31 —

Ingersoll Rand Grinder 5212 15 User Manual
Ingersoll Rand Marine Radio 651511 X User Manual
JBL Speaker HT PS300 User Manual
Jet Tools Sander M 708448 User Manual
JVC Digital Camera GR DV900 User Manual
JVC DVD Player XV N330B User Manual
Kambrook Blender KB600 User Manual
Kathrein Stereo Amplifier VWS 04 User Manual
Kenwood Stereo Amplifier KAC 1502S User Manual
Keys Fitness Tent 840EL User Manual