users manual
7. Once the first set of drivers has finished installing, Windows 98 may require the other two USB drivers
to also be installed. This will depend on what USB devices have previously been used on your system.
Simply follow the procedure outlined above until all required USB drivers have been installed.
Getting started
Getting your DG1 going is as simple as plugging it into a primary USB port of any computer running
Windows 98 or Windows 2000. There's no need to load any special software, but you will have to follow a
few simple steps to enable the Windows USB audio drivers. After you've followed these steps, make sure
to read our tips on recording before launching into a full session.
8. Once all of the required drivers have been installed, Windows 98 will start. We recommend rebooting
your computer to ensure all changes take effect.
9. Your driver installation for the DG1 is now complete.
Windows 2000 installation
Windows 98 installation
1. With USB technology, there's no need to turn off your computer when plugging the DG1 in for the first
time. Locate your computer's USB port and plug the supplied USB cable in. Now plug the DG1 into
the other end of the USB cable.
1. There's no need to turn off your computer when plugging the DG1 in for the first time. Locate your
computer's USB port and plug the supplied USB cable in. Now plug the DG1 into the other end of the
USB cable.
2. Windows 2000 will automatically detect the addition of a new USB interface. It will automatically
update your USB drivers, including USB Composite Device, USB Human Interface Device, and USB
Audio Device.
2. Windows 98 will open an Add New Hardware Wizard and let you know that it's found the DG1. It will
then start loading drivers for a USB Composite Device, USB Human Interface Device, or USB Audio
Device, depending on what components have previously been installed on your system. Click Next.
3. Once Windows 2000 has completed updating the USB drivers, it will automatically set the DG1 as your
preferred multimedia device. We recommend rebooting your computer to ensure all changes take effect.
3. Check the option Search for the best driver for your device. (Recommended) and click Next.
4. Windows 98 should already have the various USB components installed and will automatically default
to the location of the driver on your hard drive. Click Next. If Windows does not have the various USB
components loaded, it will tell you that the files could not be found. In this case, put your Windows
98 CD into the CD-ROM drive and place a check next to CD-ROM drive and then click Next.
4. Your driver installation for the DG1 is now complete.
5. The Wizard will now let you know it has located drivers for a USB Composite Device, USB Human
Interface Device, or USB Audio Device and will identify these drivers under the heading Location of
Driver. This location may be your hard drive, or CD-ROM drive, depending on what drivers your system
has previously had installed. Click Next.
Checking that the DG1 is selected as preferred device
in Windows 98 and Windows 2000
With USB technology, there's never any need to turn off your computer when unplugging or plugging in
the DG1. When you want to use the DG1, simply close any audio programs and plug it into the USB port.
Your system will automatically configure itself. When you're done, you can unplug the DG1 and your
6. The first set of drivers will now install.
2
3
computer will automatically configure for whatever soundcard is
installed. In both cases, it doesn't matter if the system is on or off.
For smooth automatic loading, please ensure all audio programs are
closed before plugging in, or unplugging the DG1.
Windows 2000
Once Windows 2000 starts and the appropriate drivers have been loaded, the DG1 will automatically be
set as your system's preferred audio device. To verify this, open the Sounds and Multimedia panel and
make sure that USB Audio Device appears in the Playback section under the Audio tab. To get to the
multimedia control panel hit Start, then go to Settings, then Control Panel. The Sounds and Multimedia
icon will be in the Control Panel window. Double click on the icon. In the Audio tab, make sure that USB
Audio Device appears in the Sound Playback section. If it doesn't, use the scroll arrow to the right and
choose USB Audio Device. You're now fully loaded.
NOTE: when the DG1 is selected as your system's preferred audio
device, no sound will come out of any speakers plugged into your
soundcard. If you wish to use your soundcard instead of the DG1,
either unplug the DG1 from the USB cable, or select your
soundcard as preferred audio device in the Multimedia Properties
control panel for Windows 98, or Sounds and Multimedia control
panel for Windows 2000. It is not possible to use a soundcard and
the DG1 at the same time.
Controlling the output and volume levels
The DG1's volume and output controls can be accessed by double clicking the
standard volume control icon. The volume for the DG1 is set by the Wave
Balance slider, which is the only slider that the DG1 uses. If there are other
sliders visible, go to Options and then Properties. In the bottom section of the
Properties window, make sure a check appears only next to Wave Balance.
Click on OK once you're done.
Windows 98
Windows 98
Once Windows 98 starts and the appropriate drivers have been
loaded, the DG1 will automatically be set as your system's preferred
audio device. To verify this, open the Multimedia Control Panel and
make sure that USB Audio Device appears in the Sound Playback
section under Preferred Device. To get to the multimedia control
panel hit Start, then go to Settings, then Control Panel. The
multimedia icon will be in the Control Panel window. Double click
on the icon to open the Multimedia Properties window. In the Audio
tab, under the heading Preferred Device, make sure that USB Audio
Device appears. If it doesn't, use the scroll arrow to the right and
choose USB Audio Device. You're now fully loaded.
Windows 2000
4
5
3. With the supplied TOSLINK cable, connect the DG1 to the Line-In of your MiniDisc recorder.
Installing MusicMatch Jukebox Plus
4. Start MusicMatch Jukebox Plus, or your favorite Windows media player, and load the selection of wav
or MP3 files to be recorded.
After the DG1's USB drivers have loaded, you will be ready to start recording. The DG1 works with any
Windows compatible media player, although to help make things easy we've included a full version of
MusicMatch Jukebox Plus. This powerful software will let you quickly rip and encode tracks from CDs, run
customized playlists, and apply graphic equalization to all of your recordings. After exhaustive testing, we
definitely think MusicMatch is one of the best programs around for getting superior results. To install
MusicMatch Jukebox Plus please do the following:
5. If you are using MusicMatch Jukebox Plus, go to point 6 now.
If you are not intending on using MusicMatch Jukebox Plus, you'll have to verify that your preferred
media player controls the Wave Balance slider in the DG1 Volume Control panel. Press play on your
media player and open the DG1 volume control panel by double clicking on the speaker icon down in
the Windows task bar at the bottom right had corner of your screen. Move the volume control up and
down on the media player and watch to see if the Wave Balance slider moves in the DG1 Volume
Control panel. If the Wave Balance slider does not move, your media player is not correctly controlling
the DG1 and may not be running to the Windows protocol. If this is the case, you will have to manually
set the volume output of the DG1 by using the Wave Balance slider rather than the volume control in
your favorite media player. You may also consider using a media player that is Windows compliant.
1. Insert the MusicMatch Jukebox Plus CD into your CD-ROM drive.
2. When the MusicMatch Jukebox Plus splash screen opens, click on the option Install Jukebox Plus 5.0
and follow the onscreen instructions.
A users manual detailing how to use MusicMatch Jukebox Plus is contained on the CD. If you wish to view
the manual, simply insert the MusicMatch CD into your CD-ROM drive and select User's Guide. For
6. Set the volume of MusicMatch Jukebox Plus or your favorite media player to minimum. Press record
on your MiniDisc recorder. Press play on MusicMatch Jukebox Plus or your favorite media player. Your
MiniDisc recorder should start recording.
NOTE: You don't have to run MusicMatch to use the DG1 - it will also work with any of your other favorite
players, including the Windows Media Player.
7. Wearing the headphones connected to the MiniDisc recorder, start to slowly raise the volume control in
MusicMatch Jukebox Plus, or your favorite media player. You will start to hear the volume increase
through the headphones.
Recording from PC to MiniDisc with the DG1
8. Make sure that you raise the volume control only to an appropriate level for your MiniDisc recorder.
If you increase the volume past the signal level that the MiniDisc recorder can tolerate, it will cause
distortion in your recording. Many MiniDisc recorders have a level display that lets you monitor the
input signal strength.
WARNING - It is important to read through these instructions carefully and to adjust the volume controls as
directed. Do not at any stage place headphones on your ears without first checking that the volume controls are
set to a minimum and slowly raised to a comfortable listening level.
9. You have set the levels of your DG1 for recording. You can now load a playlist and start a full session.
1. Before starting, make sure that the Wave Balance volume slider is set to a minimum. You can access
the DG1's volume slider by double clicking the speaker icon at the bottom right had side of the
Windows task bar.
10.MusicMatch Jukebox Plus includes a 3 second gapping feature designed to automatically add track
marks when recording to MiniDisc in analog mode. Since the DG1 is an advanced digital interface, it
automatically adds track marks without the need for a 3 second gap of silence. Make sure that you
2. Plug a set of headphones or monitor speakers into your MiniDisc recorder.
6
7
therefore disable the 3 second gapping feature in MusicMatch Jukebox Plus before recording. To do
this, Start MusicMatch Jukebox Plus, click on Options, then scroll down and click on MiniDisc Analog
Trackmarking. The check mark will disappear to show the feature is no longer enabled.
The DG1 automatically adds track marks without the need for a two or three second gap of silence
between each track. Many media players offer a gapping facility as a plug-in. Make sure to disable any
gapping feature before recording with the DG1. MusicMatch Jukebox Plus includes a special feature for
users that record using an analog source, which automatically adds a 3 second gap of silence between
tracks during playback. To turn the MusicMatch Jukebox Plus gapping feature off, click on Options, then
scroll down and click on MiniDisc Analog Trackmarking. The check mark will disappear to show the
feature is disabled.
11.During recording it not advisable to use any other applications on your system. Most MP3 players
require large amounts of resources to ensure flawless MP3 decoding and playback. If you interfere
with the computer during recording, it can effect MP3 decoding, which can in turn effect the quality
of your recording. Read the next section for further tips on getting the best results out of your DG1.
Warranties and Disclaimer
Tips for getting the best results with your DG1
The actual physical dimensions and capabilities of the DG1 may differ slightly from illustrations and
descriptions contained within this manual. Every effort has been made to ensure that electrical
functionality has been maintained wherever possible. Xitel reserves the right to change specifications of
the DG1 or the bundled software without notice. Xitel warrants the DG1 against defects in material and
workmanship for one year from the date of original purchase from an authorized dealer or Xitel
representative. This warranty only applies to the original purchaser and is not transferable. At Xitel's sole
discretion, proof of purchase and/or the DG1's serial number will be required to initiate any warranty
claim. This warranty does not cover any incompatibilities due to the user's computer, hardware, software
or any other related system configuration the DG1 is installed with. This warranty does not cover any
damage caused by negligence, non-authorized modifications, service by any other persons other than Xitel,
or if the product has been damaged by accident, abuse, misuse, negligence, or misapplication. Xitel is not
responsible for any lost profits, lost savings or other incidental or consequential damages arising out of the
use of, or inability to use, this product. That includes damage to property and, to the extent permitted by
law, damages for personal injury. This warranty is in lieu of all other warranties including implied
warranties of merchantability and fitness for a particular purpose to the extent permitted by law.
The DG1 is a high fidelity, digital medium for transferring audio between a PC and MiniDisc recorder.
Because it is digital, it will only ever send what it information it receives and cannot therefore effect the
quality of your recording in any way. If you're finding distortion in a recording, there are a couple of
possible reasons.
The first is that the original source MP3 or wav file contains distortion, or is being corrupted during
playback. Because the DG1 plays these files exactly, any anomalies in an original recording, or that occur
during playback, will also be played. To reduce the likelihood of distortion in your source file, make sure
not to use your computer for any other tasks during ripping, MP3 compression, or playback. Contact the
vendor of your ripper and encoder to make sure you meet their minimum system requirements and are
using the program correctly.
If your source file does not contain any distortion, another place that it can be corrupted is in the
MiniDisc recorder. Make sure that the DG1's output level is not set too high. Having the output of the
DG1 set higher than the maximum input level of your MiniDisc recorder can cause degradation in sound
quality. Most MiniDisc recorders have an input level indicator that allows you to monitor the strength of
the input signal. Verify that the MiniDisc recorder is not being overloaded. If distortion is still occurring,
make sure that the lens of your MiniDisc recorder is clean.
8
9
FCC Part 15 Class B Registration Warning
Warranty Claims
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
All questions regarding warranty should be directed to:
Xitel Multimedia
13276 Research Blvd
Suite 208-A
Austin, TX, 78750
Phone: 512 331 5799
Email: [email protected]
This equipment generates and uses radio frequency energy and if not installed and used properly, that is
in strict accordance with the manufacturer's instruction, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class B computing device in
accordance with the specifications in Subpart B of Part 15 of FCC Rules & Regulations, which are
designed to provide reasonable protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient the receiving antenna (2) Relocate the computer with respect to the receiver (3) Move the
computer away from the receiver (4) Plug the computer into a different outlet so that the computer and
receiver are on different branch circuits. If necessary, the user should consult a dealer or experienced
radio/television person for additional suggestions. The user may find the booklet prepared by the Federal
Communications Commission helpful: "How to Identify and Resolve Radio-TV Interference Problems". This
booklet is available from the US Government Printing Office, Washington DC 20402. Stock No 004-000-
00345-4. Shielded cables and certified Class B peripherals
must be used on this product. Using unshielded cables or
uncertified peripherals may result in this unit not complying
with FCC Rules Part 15. Changes or modifications not
expressly approved by the manufacturer could void the user's
authority to operate this equipment.
10
11
Copyright
MD-Port DG1™ and Xitel™ are trademarks of Xitel Pty Limited. MusicMatch™ and MusicMatch Jukebox
Plus™ are the trademarks of MusicMatch Inc. All other trademarks are the trademarks or registered
trademarks of their respective owners. Except as permitted under the United States Copyright Act
(1976), no part of this publication or accompanying software may be reproduced or distributed in any
form, or by any means, without the prior written permission of Xitel Pty. Ltd or MusicMatch Inc.
© Copyright 2000, Xitel Pty Limited Australia.
|