LCD COLOR MONITOR
KVX-5
INSTRUCTION MANUAL
B60-5141-08 00 JA (T)
0004
Before Applying Power
Caution: Read this page carefully to ensure safe operation.
AC adaptors are designed for operation as follows.
Europe and U.K. .................................................................. AC 230 V only
Contents
Caution: Read the pages marked
carefully to ensure safe operation.
Safety Precautions .......................................... 2
Before Applying Power .................................. 3
Introduction ........................................................... 4
Checking the Accessories ................................... 4
Using the Stand ................................................... 4
Connections ........................................................... 5
Connecting the Power Supply (AC adaptor) ........ 5
Connecting AV Equipment .................................. 5
Name and Function of Parts ................................ 6
Setting the Menu .................................................. 7
Selecting Menu Items ......................................... 7
Setting Menu ....................................................... 7
Selecting the Color System (MODE) ................... 8
Setting COLOR/TINT/PICTURE ........................... 8
Initial Resetting .................................................... 8
Selecting AV Input ................................................ 9
Adjusting the Sound Volume .............................. 9
Adjusting the Brightness of the Screen ............ 10
Listening to Sounds with Headphones ............ 10
Troubleshooting Problems ................................. 11
Specifications ........................................ Back cover
EN
3
Introduction
Keep the packing case for later usage, e.g., protection of your system in transportation for
repair services and so on.
Checking the Accessories
Check the accessories as specified below:
AC adaptor (1 set)
AV cable (1 piece)
Cushion (2 pieces)
Using the Stand
You can incline your system using the stand on the rear when looking at the screen.
Slowly pull out the stand until it stops.
Note: When pulling the stand out, do not apply an excessive force to it. A strong force can
cause stand breakage.
[Placing the system with the stand]
PHONES
AV1 IN
Stand
AV2 IN
DC IN
To make the TV more stable during use
When setting up the stand, make it more stable during use by affixing the cushion supplied
to the bottom of the set.
Front
1
Peel the seals off the double sided tape
affixed to the cushion.
2
Affix the cushion to the TV body.
EN
4
Connections
Connecting the Power Supply (AC adaptor)
Plug the AC adaptor into the AC outlet.
POWER
OFF
ON
PHONES
AV1 IN
AV2 IN
AC Adaptor
To DC IN Terminal
DC IN
Note: Be sure the POWER switch is set to the OFF position before you connect the AC
adaptor. Connecting the AC adaptor with the POWER switch set to the ON position
may cause a trouble in the system.
Connecting AV Equipment
This system is equipped with the two AV input terminals: AV1 IN and AV2 IN.
UsetheAVcablesuppliedwithyoursystemforconnectionbetweenexternalAVequip-
ment and the AV1 IN terminal or AV2 IN terminal of the system.
• Plug the video terminal of the AV cable (yellow) into a video output terminal of AV equip-
ment and plug the audio terminal (white) into audio output terminal L or R of the AV equip-
ment.
DVD Player
To Video Output
Terminal (Yellow)
PHONES
To AV1 IN or AV2 IN
Terminal
AV1 IN
AV2 IN
VCR
To Video Output
Terminal (White)
DC IN
Game Device
AV signal
AV cable
EN
5
Name and Function of Parts
1
2
POWER switch
Turns on or off the power of the system.
PHONES terminal
POWER
OFF
ON
Connects headphones. (Page 10)
• No sound will be emitted from the
speaker.
3
4
AV1 IN terminal
Inputs audio/video signals from external AV
equipment. (Page 5)
AV2 IN terminal
PHONES
Inputs audio/video signals from external AV
equipment. (Page 5)
AV1 IN
AV2 IN
5
6
DC IN terminal
Connects the AC adaptor. (Page 5)
MENU button
DC IN
Displays menu on the screen, allowing you
to select items on the menu. (Page 7)
AV1 button
TFT ACTIVE MATRIX
7
8
9
Selects the input signal of the AV1 IN termi-
nal. (Page 9)
AV2 button
Selects the input signal of the AV2 IN termi-
nal. (Page 9)
VOL. 5/∞ button
Adjusts the sound volume. (Page 9)
• Pressing the buttons at a time displays
“MUTE” at the bottom of the screen,
muting sound. Pressing the VOL. 5 or ∞
button releases the system from muting.
(Page 9)
AV1
INPUT
AV2
MENU
MENU
BRIGHT
SET
VOL.
0
BRIGHT 5/∞ button
Adjusts the brightness of the screen.
(Page 10)
In the menu display mode, the button func-
tions as the MENU SET 5/∞ button, allow-
ing you to set menus. (Page 7)
Speaker
-
A built-in monaural speaker.
Stand
=
Is pulled out to incline the system. (Page 4)
EN
6
Setting the Menu
Pressing the MENU button displays the following menu on the screen.
Menu item
Set contents
Displays AV input, AV1
or AV2 currently being
selected.
AV1
AUTO PAL
MODE
NTSC
COLOR
TINT
PICTURE
50
50
50
Note: The contents set up just before the power was turned off appears on the screen.
The screen above is an image that appears when you purchased the system.
Selecting Menu Items
The arrow (3) shows a menu item currently being selected.
Each time you press the MENU button, you can select the menu items in the following order.
MODE
COLOR
TINT
PICTURE
Setting Menu
The bullet (¶) at menu item “MODE” indicates a menu currently being selected.
For other menu items, the current settings are given in numeric values.
Each time you press the MENU SET 5/∞ button when the menu screen appears, change is
made to the setup contents of a menu item currently being selected.
EN
7
Setting the Menu (Continued)
Selecting the Color System (MODE)
You can select one of the following modes for the Color system.
AUTO:Automatically selects PAL or NTSC according to the video signal received.
PAL: Sets PAL for the Color system.
NTSC: Sets NTSC for the Color system.
1 Press the MENU button to select “MODE”.
2 Press the MENU SET 5/∞ button to select the Color system.
Each time you press the button, the setting changes as follows:
MODE
AUTO
PAL
NTSC
MODE
AUTO
PAL
NTSC
MODE
AUTO
PAL
NTSC
Selects AUTO.
Selects PAL.
Selects NTSC.
Setting COLOR/TINT/PICTURE
You can make the following adjustments in each menu item.
COLOR: Depth of color
TINT:
Tint
PICTURE: Picture quality
1 Press the MENU button and select “COLOR”, “TINT” or “PICTURE”.
2 Press the MENU SET 5/∞ button to adjust each of them.
Each time you press the button, the value changes in the range 0 to 100.
[Color adjustment sample]
COLOR
TINT
82
50
50
PICTURE
Initial Resetting
You can get the menu settings back to state at the time you purchased the system.
While pressing the MENU button, turn on the POWER switch.
POWER
MENU
OFF
ON
+
EN
8
Selecting AV Input
Select either one of the two AV inputs by using the AV1 or AV2 button.
Turning on the power selects the AV input selected just before the power was turned off.
• Pressing the AV1 button displays “AV1” at the upper right portion
of the screen for several seconds, receiving AV signals from AV
equipment connected to the AV1 terminal.
AV1
• Pressing the AV2 button displays “AV2” at the upper right portion
INPUT
of the screen for several seconds, receiving AV signals from AV
equipment connected to the AV2 terminal.
AV2
[When the AV1 button is pressed]
[When the AV2 button is pressed]
AV2
AV1
Note: If a selected AV input terminal does not receive video signals, “NO SIGNAL” ap-
pears at the bottom of the screen.
Adjusting the Sound Volume
Press the VOL. 5/∞ button to adjust the sound volume.
Adjustment values appear on the screen during adjustment.
Up
VOL.
Down
VOLUME
50
Muting Sounds:
Pressing the VOL. 5 and ∞ buttons at a time mutes sounds. “MUTE” appears on the screen
in red.
• PressingeitherVOL.5or∞buttonreleasesthesystemfrommuting.Turningoffthepower
also releases the system from muting.
MUTE
EN
9
Adjusting the Brightness of the Screen
PresstheBRIGHT5/∞ buttontoadjustthebrightnessofthescreen.
An numerical adjustment value (0~100) is displayed on the screen dur-
ing adjustment.
Up
BRIGHT
Note: The brightness of the screen differs depending on the angle at
which you see the liquid crystal panel. So, adjust the brightness
of the screen after setting the watching angle.
Down
Listening to Sounds with Headphones
You can listen to sounds with monaural headphones plugged into the system.
Stereo headphones are also available. However, you will hear monaural sounds even with
stereo headphones.
To PHONES Terminal
PHONES
AV1 IN
AV2 IN
DC IN
Note: When you use headphones, no sound will be emitted from the speaker.
EN
10
Troubleshooting Problems
If the system does not work as you expect, perform the following checks before contacting
Customer Support.
Action to be taken
Problem
No image and no sound
• Check the AC adaptor for proper connection.
• Check that the POWER switch is turned on.
• Check that the brightness and volume are
minimized or the system is put in mute state.
No image and no sound (“NO
SIGNAL” appears)
• Check the selected AV input (AV1 or AV2) for
connection to AV equipment.
• Check for reception of audio/video signals from AV
equipment.
No image, or black or white • Check the brightness for maximum or minimum.
screen
No Sound
• Check the sound volume for minimum or check
the system for being put in mute state.
• Check headphones for being plugged into the
system.
• Poor-quality image displayed
• Image doubly displayed
• Image fading
• Check for reception of radio interference from
other equipment, etc. (Turn off the power of other
equipment.)
• Image swaying
• Stripes and patterns
Inappropriate color or light color • Check COLOR, TINT, and PICTURE for proper
adjustment.
Dark screen
• Check the direction of the crystal liquid panel for
proper adjustment.
• Check the brightness for proper adjustment.
Dark screen in the initial stage • When the temperature of the system is low, the
screen becomes darker than usual just after the
power is turned on because of the characteristic of
the liquid crystal panel. Wait for a while until the
temperature goes up. The screen will get light as
usual.
• If this product interferes with radio reception during use, place it far enough away from the
radio to eliminate the interference.
EN
11
Specifications
Model Designation
Maximum external
dimensions
5.6-inch LCD Color Monitor KVX-5
Width:
Height:
Depth:
180 mm (7-1/16")
136 mm (5-3/8")
55 mm (2-3/16")
Weight (net)
AC adaptor
620 g (1.4 lb)
DC 12 V
Liquid Crystal Panel
Driving System
Light Source
Color System
Speaker
High-resolution 5.6-inch color LCD
TFT active matrix system
Backlight: High intensity fluorescent tube
PAL/NTSC
3.5-cm round type speaker with 500 mW output
• These ratings and the design are subject to change without notice for technical development.
• Lack of picture elements in part may occur in the liquid crystal panel or some picture elements
may be lit abnormally.
For your records
Record the serial number, found on the back of
the unit, in the spaces designated on the war-
ranty card, and in the space provided below. Re-
fer to the model and serial numbers whenever
you call upon your dealer for information or ser-
vice on this product.
Model
Serial Number
|