Kenwood Car Stereo System DPX MP3120 User Manual

DPX-U6120

DPX-U5120

DPX-MP3120

DUAL DIN SIZED CD RECEIVER

INSTRUCTION MANUAL

B64-4805-00/01 (M)

DSP Setup

Car Type Selection

Speaker Setting

Car Type Fine Adjustments

X’Over Setting

Audio Preset Memory

Audio Preset Recall

Basic Operations of remote control

Appendix

Accessories/ Before installation

Connecting Wires to Terminals

Installation

Log Function

Log Function recall

Log Function item lock

Deleting a Log Function item

Log Function category setting

Tuner Log Function time setting

Troubleshooting Guide

Specifications

Bluetooth Setup

Bluetooth Setting

Registering Bluetooth device

Registering PIN Code

Selecting the Bluetooth device You Wish to

Connect

Deleting a Registered Bluetooth device

Downloading the Phone Book

Adding a Voice Dialing Command

Setting a Voice Command for Category

SMS (Short Message Service)

Downloading the SMS

SMS (Short Message Service)

English

Before use

Before using this unit for the first time

This unit is initially set on the Demonstration mode.

When using this unit for the first time, cancel the

Demonstration mode. Refer to <Canceling the

Demonstration Mode> (page 6).

About discs used with this unit

• This unit can only play the CDs with

• The following discs cannot be used:

- Discs that are not round

- Discs with coloring on the recording surface or

discs that are dirty

- Recordable/Rewritable disc that has not been

finalized (For the finalization process, refer to

your disc writing software, and your disc recorder

instruction manual.)

- 8 cm (3 inch) disc (Attempt to insert using an

adapter can cause malfunction.)

2WARNING

To prevent injury or fire, take the following

precautions:

• Stop the car before operating the unit.

• To prevent a short circuit, never put or leave any

metallic objects (such as coins or metal tools) inside

the unit.

Handling discs

CAUTION

• Do not touch the recording surface of the disc.

• Adjust the volume so that you can hear sounds

outside the car. Driving with the volume too high

may cause an accident.

• Wipe off the dirt on the panel with a dry silicon or

soft cloth.

• Do not stick tape etc. on the disc, or use a disc with

tape stuck on it.

• Do not use any accessories for the disc.

• Do not use any solvents to clean discs. Use a dry

silicon or soft cloth.

• Clean from the center of the disc and move

outward.

Failure to observe this precaution may result in

damage to the monitor or unit.

• When removing discs from this unit, pull them out

horizontally.

• Remove the rims from the center hole and disc

edge before inserting a disc.

Condensation

When the car is air-conditioned, moisture may collect

on the laser lens. This may cause disc read errors. In

this case, remove the disc and wait for the moisture

to evaporate.

How to reset your unit

Notes

If the unit fails to operate properly, press the Reset

button. The unit returns to factory settings when the

Reset button is pressed.

• If you experience problems during installation,

consult your Kenwood dealer.

• When you purchase optional accessories, check with

your Kenwood dealer to make sure that they work

with your model and in your area.

• Characters that conform to ISO 8859-1 can be

displayed.

• To display characters in the following language,

additional setting is required.

Chinese: Refer to “Chinese” of <Initial Settings>

(page 30).

• The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on the

display on the actual equipment, and some of the

illustrations on the display may be inapplicable.

Reset button

DPX-U6120/ DPX-U5120/ DPX-MP3120

Component names and functions

q p

7 6

1 Disc slot

DPX-U6120 DPX-U5120

[iPod] button

Select the iPod source.

When inserted a disc (label side up), the source is

switched automatically and a song starts playing.

2 [0] button

To eject the disc.

3 [1] – [6] button

DPX-MP3120

[38] button

To start or interrupt playback for CD and Audio

file.

Mute the volume. (During Tuner, AUX source)

4] / [¢] button

To select a station, song and setting items.

To recall the memorized station.

Switches the play mode between music discs,

Audio files, and iPod.

q [

4 [DISP] button

To change the display mode.

w [BAND] button

5 [ATT] button

Turning the volume down quickly.

6 [ ] button

To select the receiving band, and the folder for

Audio file.

e [SRC] button

To enter the music search mode.

7 [ ] button

To return to previous item.

8 [VOL] knob

To turn on this unit and select the Source.

To turn off this unit (press the button at least 1

second).

r Auxiliary Input Terminal

Portable audio device can be connected with the

mini-plug (3.5 mm ø).

To adjust volume.

Enters function setting mode and setting item

(turn and press the knob). Refer to <Function

setting Operation> (page 7) for details.

• Use the mini-plug cable which is stereo type and does

not have any resistance.

DPX-U6120 DPX-U5120

DPX-U6120

USB Terminal

When connecting, open up the USB terminal lid. A

USB device or an iPod can be connected.

[LOG] button

To display a Log Function list

DPX-U5120 DPX-MP3120

[B.BOOST] button

To boost the bass tone in two steps (LV1, LV2,

OFF).

English

General operation

Adjusting the Clock

DPX-U6120

Press the [VOL] knob to enter the Function

setting mode.

SRC

The item can be selected and determined as

follows.

”Settings” ➜ “Clock & Date” ➜ “Clock Adjust”

To select the item, turn the [VOL] knob. To

determine the item, press the [VOL] knob.

DPX-U6120

DPX-U5120

iPod

VOL

Before Using

Press [4] or [¢] button to select hour or

minute to set.

Canceling the Demonstration Mode

Cancel the demonstration mode when you use it for

the first time after installation.

Turn the [VOL] knob to adjust the hour and

minute.

Press the [VOL] knob to finish the Clock

adjusting.

Press the [VOL] knob to cancel the demonstration

mode when the messages “To cancel DEMO

press the volume knob”/ “CANCEL DEMO PRESS

VOLUME KNOB” are displayed (approx. 15

seconds).

Press the [

] knob for at least 1 second, and

then press it again briefly to exit the Function

setting mode.

Turn the [VOL] knob to select “YES” and press the

[VOL] knob.

DPX-U5120 DPX-MP3120

Press the [B.BOOST] button for at least 1 second.

⁄

Turn the [VOL] knob to adjust the hour, and then

press the [VOL] knob.

• Demonstration mode can also be cancelled in “DEMO

Mode” of Function setting mode. Refer to <Demonstration

mode Setting> (page 31).

Turn the [VOL] knob to adjust the minute, and

then press the [VOL] knob.

DPX-U6120/ DPX-U5120/ DPX-MP3120

Common Operation

Function setting Operation

The basic operating procedure for using this

function is described below. The individual function

items are covered in the operating procedures.

Power and source select

Turns the power ON by pressing the [SRC]

button.

Select the source

Press the [SRC] button.

Function items vary from source to source.

When the power is ON, select a source.

Press the [SRC] button each time switches

between sources.

Tuner (“TUNER”) ➜ USB (“USB”) or iPod (“iPod”)

(DPX-U6120/ DPX-U5120 only) ➜ CD (“CD”) ➜

Auxiliary input (“AUX”) ➜ Standby (“STDBY”/

“STANDBY”) ➜ Tuner...

Enter Function setting mode

Press the [VOL] knob.

Select the setting item

Turn the [VOL] knob and press it when the

desired item is displayed.

DPX-U6120 DPX-U5120

Repeat the operation until your desired setup item

is selected.

Operation example:

Press the [iPod] button to switch the source to

iPod.

Press the [SRC] button for at least 1 second to

turns the power OFF.

1[VOL]

]

⁄

Settings

Exit

Seek Mode

• The SRC Select mode can be set in “Source Select” of <Initial

Settings> (page 30). (DPX-U6120 only)

• When an optional accessory is connected, the source name

for each device appears. (DPX-U6120 only)

• When connection of the iPod is recognized, the source

display changes from “USB” to “iPod”.

[VOL]

[

]

Auto Memory

Audio Control

1 sec.

Volume

In this manual, the above selection is indicated as

Select “Settings”/ “SETTINGS” >“Seek Mode”/

“SEEK MODE”.

Turning the [VOL] knob adjusts the sound

volume.

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

Exit Function setting mode

Press the [ ] button for at least 1 second.

English

Function of DPX-U6120/ DPX-U5120

iPod/iPhone Operation

Select a song

Operation type

Move between items

Select an item

Skip Search

Return to previous item

Operation

1 – 6

Turn the [VOL] knob.

Press the [VOL] knob.

Press the [4] or [¢] button.

Press the [ ] button.

SRC

✍ For example: Searching by Artist name.

Turn the [VOL] knob and press it when the

desired item is displayed.

4 ¢

iPod

VOL

Select “Artists”/ ”ARTISTS” > Artist name > Album

name > Song title

Basic Operation

Cancelling Enter Music search mode

Press the [ ] button for at least 1 second.

Playing iPod

• Connect an iPod

When connected, the source is switched

⁄

• Characters which cannot be displayed are left blank. If non

of the characters can be displayed, the browse item name

and digits are displayed.

automatically and a song starts playing.

• Select iPod source

Press the [iPod] button.

Items

Playlists

Artists

Albums

Songs

Display

“PLIST***” Podcasts

“ART***”

“ALB***”

“PRGM***”

Items

Display

“PDCT***”

“GEN***”

“COM***”

⁄

Genres

Composers

• KCA-iP101/iP102 (optional accessory) is recommended to

connect an iPod.

Song Select

Press the [4] or [¢] button.

•

Set the ratio with “Skip Search” in <iPod Setting> (page 9).

Fast Forwards or Fast Backwards

Hold down the [4] or [¢] button.

Play function

Repeat play

Press the [4] button.

Switches between Repeat (“File Repeat ON”/ “FILE

REPEAT”) and off (“File Repeat OFF”/ “REPEAT OFF”)

when pressed.

Pause and Play

Press the [6] button to pause or resume

playback.

Remove iPod

Select a source other than the iPod

Press the [SRC] button.

Random play

Press the [3] button.

Randomly plays the music.

Remove the iPod.

Pressing the button toggles the setting between

Random play on (“Folder Random ON”/ “FOLDER

RANDOM”) and off (“Folder Random OFF”/

“RANDOM OFF”).

⁄

• Removing the iPod with it selected as a source can damage

the data stored in the iPod.

Press this button again cancels the Random play.

Selecting a song by browsing iPod

All Random play

Searching for the song you want to play.

Press the [3] button for at least 1 second.

All songs in iPod are played at random.

Pressing the button toggles the setting between All

random play on (“All Random ON”/ “ALL RANDOM”)

and off (“All Random OFF”/ “RANDOM OFF”).

Press this button again cancels the All Random

play.

Select iPod source

Press the [iPod] button.

Enter Music search mode

Press the [ ] button.

DPX-U6120/ DPX-U5120/ DPX-MP3120

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• The time required to turn on the all random function may

become longer depending on the number of songs in iPod.

• Turning on the all random function changes the iPod

browse item to “Songs”. This browse item will not be

⁄

• The setting of “Skip Search” in <iPod Setting> (page 9)

and that in <USB Setting> (page 14) are always the same.

Changing the setting of one reflects the other.

changed even if the all random function is turned off.

• If the browse item is changed to search for music while the

all random function is on, the all random function is turned

off and the songs in the browse item are played at random.

Selecting the Search mode

You can select the most suited search method

for the desired song from 4 types of the Search

mode.

iPod Control by Hand Mode

Allowing you to operate iPod with the control on the

iPod.

Press the [iPod] button for at least 1 second.

When the iPod control by hand mode is selected,

“iPod by Hand Mode”/”HANDS ON” is displayed.

Search mode Operation Overview

“Related Search”/ Press the Searches for music of the same artist or

“RELATED SRCH” [1] button. genre as the one being played.

Refer to the <Related Search>

(page 10).

⁄

“Direct Search” Press the You can quickly search the desired song

[2] button. by specifying its Search item (artist,

album, etc.) and initial.

• In the iPod Control by hand mode, iPod cannot be operated

using this unit.

• This mode is not compatible with music information display.

The display will show “iPod by Hand Mode”/ “iPod MODE”.

• iPod can be operated when it conforms to the iPod control

function.

Function of DPX-U6120.

Refer to <Direct Search> (page 10).

“Alphabet

Search”/

“ALPHABET

SRCH”

Press the You can select an alphabetic character

[3] button. from the list in the Search item (artist,

album, etc.) selected now.

Refer to <Alphabet Search> (page 11).

Press the Registers a song to My Playlist.

iPod Setting

“Register My

You can select the following iPod Setting items.

Playlist”/“Recall [5] button. Refer to <My Playlist> (page 12).

My Playlist”/“MY

PLAYLIST”

Select iPod source

Press the [iPod] button.

Select iPod source

Press the [iPod] button.

Enter Function setting mode

Press the [VOL] knob.

Enter Music search mode

Press the [ ] button.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings”/ “SETTINGS”.

Select the Search mode

Press the [1]/ [2]/ [3]/ [5] button.

Select the setting item

Turn the [VOL] knob and press it when the

Cancelling Music search mode

desired item is displayed.

Press the [ ] button for at least 1 second.

Display

Overview

“Settings”/

“SETTINGS”

“Skip Search”/ Sets the ratio of skip performed with <Skip

“SKIP SEARCH” Search> (page 8).

“0.5%”/ “1%”/ “5%”/ “10%”

“Delete My

Deletes the registered My Playlist.

Playlist”/“MPLIST Refer to <Deleting a Song from the Playlist>

DELETE”

(page 12) for the operation.

(

: Factory setting)

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

English

Function of DPX-U6120/ DPX-U5120

iPod/iPhone Operation

Function of DPX-U6120

Related Search

Direct Search

Searches for music of the same artist or genre as the

one being played.

You can quickly search the desired song by

specifying its Search item (artist, album, etc.) and

initial.

Select iPod source

Press the [iPod] button.

Select iPod source

Press the [iPod] button.

Enter Music search mode

Press the [ ] button.

Enter Music search mode

Press the [ ] button.

Enter Related search mode

Press the [1] button.

Enter Direct Search mode

Press the [2] button.

Select the Search item

Turn the [VOL] knob and press it when the

desired Search item is selected.

Select the Search item

Turn the [VOL] knob and press it when the

Display

Searches music

desired Search item is selected.

“Search Artist”/

“SRCH ARTIST”

Displays the album of the same artist.

Display

“PLAY LIST”

“ARTIST”

“ALBUM”

“SONG”

Items

Playlists

Artists

Albums

Songs

Display

“PODCAST”

“GENRE”

Items

Podcasts

Genres

“Search Album”/ Displays music in the album in which the one

“SRCH ALBUM”

“Search Genre”/

“SRCH GENRE”

being played is included.

Displays the artist of the same genre.

“COMPOSER”

Composers

“Search Composer”/ Displays the album including music created by the

“SRCH COMPOSER” same Composer.

Select the character to be searched for

After this step, you need to browse. See step 3 of

<Selecting a song by browsing iPod> (page 8) to

select a song.

Operation type

Move between items

Select an item

Operation

Turn the [VOL] knob.

Press the [VOL] knob.

Press the [4] or [¢] button.

Move to the next column

Cancelling the Related search

Press the [ ] button for at least 1 second.

Up to 3 characters can be entered.

⁄

Determine the selected initial

Turn the [VOL] knob and press it when the

desired item is displayed.

• Related search cannot be performed while playing the

Podcast.

• When the music being played has no information on

browsing items or no music was found, “Not Found”/ “NOT

FOUND” is displayed.

Select “DONE”.

Start search. When search is completed, the music

search mode is selected again at the selected

character position.

After this step, you need to browse. See step 4 of

<Selecting a song by browsing iPod> (page 8) to

select a song.

Cancelling the Direct Search

Press the [ ] button for at least 1 second.

⁄

• Characters that can be entered are alphabetical characters

(A to Z), numerical characters(0 to 9), and “ * ”.

• “ * ” indicates characters other than alphabetical and

numerical characters. You cannot enter any more characters

when entering “ * ” in the first character position.

• If the first character string begins with an article “a”, “an”, or

“the” in the Direct Search mode, it is searched for in defiance

of the article.

10 DPX-U6120/ DPX-U5120/ DPX-MP3120

Alphabet Search

You can select a song by alphabet. This function

searches songs whose name contain the specified

character(s) in the list of the selected Search item

(artist, album, etc).

Select iPod source

Press the [iPod] button.

Enter Music search mode

Press the [ ] button.

Select search item

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the item (artist, album, etc.) you want to

search.

Enter Alphabet Search mode

Press the [3] button.

Search for song

DPX-U6120

Operation type

Select the character

Select an item

Operation

Turn the [VOL] knob.

Press the [VOL] knob.

DPX-U5120

Operation type

Select the character

Move the cursor to the

enter character position

Determine the selected

character

Operation

Turn the [VOL] knob.

Press the [4] or [¢] button.

Press the [VOL] knob.

Cancelling the Alphabet Search

Press the [ ] button for at least 1 second.

⁄

• The time of search by alphabet may become long

depending on the number of songs or items in iPod.

• If the first character string begins with an article “a”, “an”,

or “the” in the Alphabet Search mode, it is searched for in

defiance of the article.

English

Function of DPX-U6120/ DPX-U5120

iPod/iPhone Operation

Turn the [VOL] knob to select “YES”, and then

press the [VOL] knob.

“Completed”/ “COMPLETED” is displayed.

My Playlist

Allows you to register your favorite songs in the

Playlist of this unit. You can register up to 10 songs

in the Playlist.

Deleting the all song from the Playlist (In

Function setting mode)

Registering Songs in the Playlist

Enter Function setting mode

Press the [VOL] knob.

Play the song you want to register

Enter Delete Playlist mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings”/ “SETTINGS” > “Delete My

Playlist”/ “MPLIST DELETE”.

Press the [5] button for at least 2 second.

“## Stored”/ “## STORED” (Registration number) is

displayed.

⁄

• Make a Playlist from the songs stored in one iPod. If you

attempt to register a song stored in a different iPod, ”No

Information”/ “NO INFO” appears and then ”Delete My

Playlist All Delete?”/ “MPLIST DELETE” appears. Select “YES” to

delete the Playlist when you want to remake it.

• If you attempt to register the eleventh song, ”Memory

Full”/ ”MEMORY FULL” appears and you cannot register it

accordingly. To register the song, delete an unnecessary

song.

Turn the [VOL] knob to select “YES”, and then

press the [VOL] knob.

“Completed”/ “COMPLETED” is displayed.

⁄

• If you connect the different iPod from one registered to

My Playlist, “Delete One”/ “DELETE ONE” and “Delete All”/

“DELETE ALL” will not appear and all songs be deleted.

• Do not register Podcasts. Songs you do not want to register

may be registered, or playback may not be carried out

correctly.

Playing the Song in the Playlist

Enter Playlist mode

Press the [5] button.

Play the song in the Playlist

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the song you want to play.

⁄

• Turning ACC OFF or the power OFF cancels the My Playlist

mode.

• The ending of a song may be cut unless the song has a

silence of 1 second or longer at the end.

• Random play cannot be performed during playback of a

song in the Playlist.

Deleting a Song from the Playlist

Enter Playlist mode

Press the [5] button.

Enter Delete Playlist mode

Press the [VOL] knob for at least 1 second.

Select Delete Playlist mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select ”Delete One”/ “DELETE ONE” or ”Delete

All”/ “DELETE ALL”.

12 DPX-U6120/ DPX-U5120/ DPX-MP3120

Function of DPX-U6120/ DPX-U5120

USB device Operation

File Search

Selecting the file you want to listen to from the

device being played now.

2 – 6

Select USB source

Press the [SRC] button.

SRC

Select the “USB” display.

Enter Music search mode

Press the [ ] button.

4 ¢

BAND

VOL

Select a file

Basic Operation

Operation type

Move between items

Select an item

Operation

Turn the [VOL] knob.

Press the [VOL] knob.

Playing USB device

• Connect a USB device

When connected, the source is switched

Skip Search (Function of Music Press the [4] or [¢] button.

Editor media)

automatically and a song starts playing.

Return to previous item

Press the [ ] button.

✍ For example: Searching for ¡".

Turn the [VOL] knob and press it when the

desired item is displayed.

• Select USB source

Press the [SRC] button.

Select the “USB” display.

Select “Music” > 1 > 2 > ¡"

⁄

• CA-U1EX (optional accessory) is recommended to connect

a USB device.

¡"

¡!

¡#

Moving to the next folder

Press the [BAND] button.

Cancelling Music search mode

⁄

Press the [ ] button for at least 1 second.

• The Music Editor media does not allow you to select a

⁄

folder.

• Set the ratio with “Skip Search” in <USB Setting> (page 14).

Song Select

Press the [4] or [¢] button.

Fast Forwards or Fast Backwards

Hold down the [4] or [¢] button.

⁄

• No sound is output while playing Audio file

Pause and Play

Press the [6] button to pause or resume

playback.

Remove USB device

Select a source other than the USB

Press the [SRC] button.

Remove the USB device.

⁄

• Removing the USB device with it selected as a source can

damage the data stored in the USB device.

English

Function of DPX-U6120/ DPX-U5120

USB device Operation

Play function

USB Setting

You can select the following USB Setting items.

Scan play

Press the [2] button.

Successively plays the intro of the music in the

Select USB source

Press the [SRC] button.

folder.

Select the “USB” display.

When Scan Play is turned on, “File Scan ON”/ “FILE

SCAN” is displayed.

Pressing this button again plays songs in the

normal mode starting with the song being played

now.

Enter Function setting mode

Press the [VOL] knob.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings”/ “SETTINGS”.

Random play

Press the [3] button.

Randomly plays the music in the folder.

When Random Play is turned on, “Folder Random

ON”/ “FOLDER RANDOM” is displayed.

Press this button again cancels the Random play.

Select the setting item

Turn the [VOL] knob and press it when the

desired item is displayed.

Display

Overview

“Settings”/

“SETTINGS”

Repeat play

Press the [4] button.

Switches between File Repeat (“File Repeat ON”/

“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/

“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/

“REPEAT OFF”) when pressed.

“Skip Search”/ Sets the ratio of skip performed with <Skip

“SKIP SEARCH” Search (Function of Music Editor media)>

(page 13).

“0.5%”/ “1%”/ “5%”/ “10%”

(

: Factory setting)

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

⁄

• The Music Editor media does not allow you select folder

Exit Function setting mode

Press the [ ] button for at least 1 second.

repeat play.

⁄

• The setting of “Skip Search” in <iPod Setting> (page 9)

and that in <USB Setting> (page 14) are always the same.

Changing the setting of one reflects the other.

14 DPX-U6120/ DPX-U5120/ DPX-MP3120

Music CD/ Audio file Operation

DPX-MP3120

Function of Internal CD source

Music Search

Selecting the music you want to listen to from the

disc being played now.

2 – 6

Select CD source

Press the [SRC] button.

Select the “CD” display.

SRC

Enter Music search mode

Press the [ ] button.

4 ¢

BAND

VOL

Search for music

Basic Operation

Operation type

Move between items

Select an item

Operation

Turn the [VOL] knob.

Press the [VOL] knob.

Press the [ ] button.

Disc play

• Insert a disc.

When inserted, the source is switched

Return to previous item

automatically and a song is starts playing.

When a CD is inserted, the “IN” indicator is ON.

Cancelling Function setting mode

Press the [ ] button for at least 1 second.

• Select CD source

Press the [SRC] button.

Select the “CD” display.

Play function

Scan play

Press the [2] button.

Successively plays the intro of the music in the disc

Disc ejection

Press the [0] button.

or folder.

Moving to the next folder

When Scan Play is turned on, “Track Scan ON”/

“TRACK SCAN”/ “File Scan ON”/ “FILE SCAN” is

displayed.

Pressing this button again plays songs in the

normal mode starting with the song being played

now.

Press the [BAND] button.

⁄

• This operation can be performed only for the Audio file.

Song Select

Press the [4] or [¢] button.

Fast Forwards or Fast Backwards

Hold down the [4] or [¢] button.

Random play

Press the [3] button.

Randomly plays the music in the disc or folder.

When Random Play is turned on, “Disc Random

ON”/ “DISC RANDOM”/ “Folder Random ON”/

“FOLDER RANDOM” is displayed.

⁄

• No sound is output while playing Audio file.

Pause and Play

DPX-U6120 DPX-U5120

Press this button again cancels the Random play.

Press the [6] button to pause or resume

playback.

Repeat play

Press the [4] button.

DPX-MP3120

Switches between Track Repeat (“Track Repeat ON”/

“TRACK REPEAT”) and OFF (“Track Repeat OFF”/

“REPEAT OFF”) when pressed while playing a CD.

Switches between File Repeat (“File Repeat ON”/

“FILE REPEAT”), Folder Repeat (“Folder Repeat ON”/

“FOLDER REPEAT”), and OFF (“Folder Repeat OFF”/

“REPEAT OFF”) when pressed while playing an

Audio file.

Press the [38] button to pause or resume

playback.

English

Music CD/ Audio file Operation

Function of DPX-U6120

Function of DPX-U6120 with disc changer and

remote control

Basic Operation of Disc Changer

(Optional)

Direct search in Disc changer

(Optional)

Select CD changer source

Press the [SRC] button.

Select the “CD CH” display.

Searching the disc or music by entering the disc or

music number.

1 Enter Direct search mode

Press the [DIRECT] button on the remote

control.

Moving to the next disc

Press the [BAND] button.

Song Select

Press the [4] or [¢] button.

“– –” is displayed.

2 Enter the disc or music number

Press the number buttons on the remote

control.

Fast Forwards or Fast Backwards

Hold down the [4] or [¢] button.

Pause and Play

Press the [6] button to pause or resume

playback.

3 Search the disc

Press the [FM] or [AM] button on the remote

control.

Playing the Current Song or Disc Repeatedly.

(Repeat play)

Press the [4] button.

Switches between Track Repeat play on (“Track

Repeat ON”), Disc Repeat play on (“Disc Repeat

ON”), and Repeat play off (“Repeat OFF”) when

pressed.

4 Search the music

Press the [4] or [¢] button on the remote

control.

Cancelling Direct search

Press the [

] button on the remote control.

⁄

• Input “0” to select disc 10.

Randomly plays the music in the disc changer.

(Magazine random play)

Press the [5] button.

When Magazine random play is turned on,

“Magazine Random ON” is displayed.

Press this button again cancels the Magazine

random play.

Function of remote control

Direct music search

Searching the music by entering the track number.

1 Enter Direct Music search mode

Press the [DIRECT] button on the remote

control.

“– –” is displayed.

2 Enter the music number

Press the number buttons on the remote

control.

3 Search the music

Press the [4] or [¢] button on the remote

control.

Cancelling Direct music search

Press the [

] button on the remote control.

16 DPX-U6120/ DPX-U5120/ DPX-MP3120

Tuner Operation

“Auto Memory”/ Memorizes 6 stations with good reception

“AUTO MEMORY” automatically.

Refer to <Auto Memory Entry> (page 17).

“Forced MONO”/ Reduces the noise when stereo broadcasts are

“FORCED MONO” received as monaural.

“ON”/ “OFF”

1 – 6

SRC

(

: Factory setting)

Make a setting

Turn the [VOL] knob.

4 ¢

BAND

VOL

Exit Function setting mode

Press the [ ] button for at least 1 second.

Basic Operation

Remarks

• Forced MONO

Selecting Tuner source

Press the [SRC] button.

Select the “TUNER” display.

Strong electrical fields (such as from power lines) may

cause unstable sound quality when it is set to ON. In such

a situation, turn it OFF.

Selecting the Receiving Band

Press the [BAND] button.

Pressing the button switches the receiving band

(FM1, FM2, FM3, AM).

Station Preset Memory

Putting a station in the memory.

Select the frequency to put in the memory

Press the [4] or [¢] button.

Selecting the Receiving station

Press the [4] or [¢] button.

✍ Details of the station selecting in operation are

set in the “Seek Mode”/ “SEEK MODE” of <Tuner

Setting> (page 17).

Select the number to put in the memory

Press the [1] – [6] button for at least 2 seconds.

⁄

• Up to 6 stations with a different band (FM/AM) can be

memorized to the [1] – [6] button according to the setting

of “Tuner Preset Type”/ “PRESET TYPE” of <Initial Settings>

(page 30).

Tuner Setting

You can select the following Tuner Setting items.

Select Tuner source

Press the [SRC] button.

Select the “TUNER” display.

Auto Memory Entry

Putting stations with good reception in the memory

automatically.

Enter Function setting mode

Press the [VOL] knob.

Turn the [VOL] knob and press it when the desired

item is displayed.

Select “Settings”/ “SETTINGS”.

Select the radio band you wish to store in the

preset memory

Enter Function setting mode

Press the [VOL] knob.

Select the setting item to adjust

Turn the [VOL] knob and press it when the desired

item is displayed.

Enter Auto Memory Entry mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Display

Overview

“Settings”/

“SETTINGS”

Select “Settings”/ “SETTINGS” > “Auto

Memory”/ “AUTO MEMORY”.

“Seek Mode”/ Selects the tuning mode of the radio.

“SEEK MODE”

“Auto1”/ “AUTO1”: Automatic search for a

Open Auto Memory Entry

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “YES”.

station.

“Auto2”/ “AUTO2”: Search in order of the

stations in the Preset memory.

“Manual”/ “MANUAL”: Normal manual

tuning control.

When 6 stations that can be received are put in the

memory, auto memory entry closes.

English

Tuner Operation

Preset Tuning

Frequency Step Setting

Recalling the stations in the memory.

Changing the tuning frequency step.

The original setting is FM band 50 kHz, and AM

band 9 kHz.

Select the radio band

Recalls the memorized station

Press the [1] – [6] button.

1 Turn the power OFF

Press the [SRC] button for at least 1 second.

Function of remote control

2 Switch the frequency step

While pressing the [1] and [5] buttons, press the

[SRC] button.

Direct access tuning

Entering the frequency and tuning.

Release your fingers from the button after the

1 Enter Direct access tuning mode

Press the [DIRECT] button on the remote

control.

display appears.

The frequency step changes to FM band 200 kHz,

and AM band 10 kHz.

“– – – –” is displayed.

⁄

2 Enter the frequency

• When the same operation is repeated, the frequency step

returns to the original setting.

Press the number buttons on the remote

• When the frequency step is changed, the frequencies in the

memory are deleted.

control.

Example:

Desired frequency Press button

92.1 MHz (FM)

810 kHz (AM)

[9], [2], [1]

[8], [1], [0]

3 Search the frequency

Press the [4] or [¢] button on the remote

control.

Cancelling Direct access tuning

Press the [

] button on the remote control.

18 DPX-U6120/ DPX-U5120/ DPX-MP3120

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Bluetooth Audio Operation

Basic Operation

Selecting Bluetooth Audio source

Press the [SRC] button.

Select the “BT Audio” display.

SRC

Pause and play

Press the [6] button.

4 ¢

Music Search

Press the [4] or [¢] button.

⁄

Connecting a Bluetooth Device

• All or some of the operations above cannot be performed if

the Bluetooth audio player is not ready for remote control.

• Switching between Bluetooth audio sources does not start

or stop playback automatically. Perform the operation for

starting or stopping playback.

• Some audio players cannot be controlled remotely or

reconnected after Bluetooth disconnection. Operate the

main unit of the audio player to connect Bluetooth.

Before use the Bluetooth device, you need to

connect Bluetooth device to this unit.

Pairing (Registering from Bluetooth devices)

To make your Bluetooth Audio player usable with

this unit, you need to register it (pairing).

Turn on this unit

Press the [SRC] button.

Start registering this unit by operating the

Bluetooth device

By operating the Bluetooth device, register the

audio player (pairing). Select “KCA-BT200”/ “KCA-

BT300” from the list of connected units.

Enter a PIN code

Input the PIN code (“0000”) in the Bluetooth

device.

Check that registration is complete on the

Bluetooth device.

✍ PIN code is set to “0000” as the default. You can

change this code. Refer to <Registering PIN

Code> (page 44).

By operating the Bluetooth device, start

Bluetooth connection.

⁄

• If pairing does not succeed, try followings.

– PIN code is set to “0000”. See <Registering PIN Code>

(page 44)

– Turn off the power of this unit and turn it back on. And

then try the pairing operation again.

– If other audio players have been registered, delete them.

And then try the pairing operation again. See <Deleting a

Registered Bluetooth device> (page 45)

• When registering from this unit, refer to <Registering

Bluetooth device> (page 43).

English

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Operation of hands-free phoning

⁄

• When registering from this unit, refer to <Registering

1 – 6

Bluetooth device> (page 43).

Receiving a Call

DISP

ATT

SRC

Answering a Phone Call

Press the [VOL] knob.

4 ¢

LOG VOL

⁄

• The following operations disconnect the line:

- Insert a CD.

Connecting a Bluetooth Device

- Connect a USB device.

• The name of the calling party is displayed if it has already

been registered in the Phone Book.

Before use the Bluetooth device, you need to

connect Bluetooth device to this unit. The following

3 steps procedure is necessary.

Rejecting an Incoming Call

Step 1. Pairing (Registering from Bluetooth

devices)

Press the [SRC] button.

To make your Bluetooth device (cell-phone) usable

with this unit, you need to register it (pairing).

During a Call

Disconnecting a Call

Press the [SRC] button.

Turn on this unit

Press the [SRC] button.

Switching to the Private Mode

Press the [6] button.

Switches between Private talk (“PRIVATE”) and

Start registering a this unit by operating the

Bluetooth device

By operating the Bluetooth device, register the

hands-free unit (pairing). Select “KCA-BT200”/ “KCA-

BT300” from the list of connected units.

Hands-free talk each time this button is pressed.

⁄

• Depending on the type of your cell-phone, switching

to the private talk mode may select the source that was

used before commencing the hands-free connection. If

this happens, the source cannot be switched back to the

hands-free talk mode by operating this unit. Operate your

cell-phone to return to the hands-free talk mode.

Enter a PIN code

Input the PIN code (“0000”) in the Bluetooth

device.

Check that registration is complete on the

Bluetooth device.

✍ PIN code is set to “0000” as the default. You can

change this code. Refer to <Registering PIN

Code> (page 44).

Adjusting the Voice Volume during a Call

Turn the [VOL] knob.

By operating the Bluetooth device, start hands-

free connection.

Call Waiting

Step 2. Connection

Answering Another Incoming Call with the

Current Call Suspended

If you have registered 2 or more cell-phones, you

need to select one of them. For more details,

see <Selecting the Bluetooth device You Wish to

Connect> (page 44).

When a cell-phone is connected, the “BT” indicator

is light up.

Press the [VOL] knob.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “ANSWER”.

Step 3. Hands-free phoning

You can do hand-free phoning when the

connection is made.

Answering another Incoming Call after

Terminating the Current Call

Press the [SRC] button.

20 DPX-U6120/ DPX-U5120/ DPX-MP3120

Continuing the Current Call

Speed Dialing (Preset Dial)

Press the [VOL] knob.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “REJECT”.

Select the number you want to recall from the

memory

Press the [1] – [6] button.

Answering the Waiting Call after Terminating

the Current Call

Press the [SRC] button.

Make a call

Press the [VOL] knob.

Switching between the Current Call and Waiting

Call

Press the [VOL] knob.

Each pressing of this knob switches the calling

⁄

• You need to register the preset dial number. Refer to

<Registering to the Preset Dial Number List> (page 22).

party.

Calling a Number in the Phone Book

Other Functions

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Clearing the Disconnection Message

Press the [LOG] buttons for at least 1 second.

“HF Disconnect”/ “HF D-CON” disappears.

Select the Phone Book mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Phonebook”.

Making a Call

Select the initial to be searched for

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Operation type

Operation

Move to the next character. Turn the [VOL] knob.

Determine the selected initial. Press the [VOL] knob.

Select a dialing method

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the name

Operation type

Operation

Display

Overview

Select the Phone number.

Select the name.

Turn the [VOL] knob.

“Phonebook” Selecting the initial to be searched for the phone

book.

“Incoming Calls” Calling a number in the incoming call list.

“Outgoing Calls” Calling a number in the outgoing call list.

“Missed Calls” Calling a number in the missed calls list.

“Number Dial” Making a call by entering phone number.

Press the [

4] or [¢] button.

✍ Switching between Display Modes

Press the [DISP] button.

Make a call

Press the [VOL] knob.

Operation method of each mode is described

below.

⁄

• During search, a non-accent character such as “u” is

Exit the dialing method mode

Press the [LOG] button for at least 1 second.

searched for instead of an accent character such as “ü”.

English

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Operation of hands-free phoning

Calling a Number in the Call log

Make a Voice Dialing Call

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Enter voice recognition mode

Press the [ATT] button for at least 1 second.

Select the call log mode

Turn the [VOL] knob and press it when the

desired item is displayed.

“PB Name?” is displayed.

When a beep is heard, say the name within 2

seconds.

Select “Outgoing Calls” (outgoing call),

“Incoming Calls” (incoming call), or “Missed

Calls” (missed call).

“PN Type?” is displayed.

When a beep is heard, say the category name

within 2 seconds.

Select a name or phone number

Turn the [VOL] knob.

✍ Switching between Display Modes

Press the [DISP] button.

Make a call

Press the [VOL] knob.

✍ This step is the same as step 4 of the procedure

in <Calling a Number in the Phone Book> (page

21). You can make a call or select a category.

Make a call

Press the [VOL] knob.

⁄

• If your voice cannot be recognized, a message is displayed.

Pressing the [VOL] knob allows you to retry voice input.

Refer to <Troubleshooting Guide> (page 56).

• Both the name and category require registration of a voice

tag. Refer to <Setting a Voice Command for Category>

(page 46).

• The outgoing call list and the incoming call list, and the

missed call list are the lists of calls originated from and

received at this unit. They are not the ones stored in the

cell-phone memory.

• Audio sound is not output during voice recognition.

Dial a Number

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Registering to the Preset Dial Number

List

Select the number dial mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the phone number you wish to register

Select the phone number with reference to the

following:

- <Calling a Number in the Phone Book> (page 21)

- <Calling a Number in the Call log> (page 22)

- <Dial a Number> (page 22)

Select “Number Dial”.

Enter a phone number

Operation type

Operation

Select the numbers.

Move to the next digit.

Delete the last digit.

Turn the [VOL] knob.

Select the number to put in the memory

Press the [1] – [6] button for at least 2 seconds.

Press the [

] button.

• Press the number ([1] – [0]), #([FM]), *([AM]), or

+([¢]) button on the remote controller.

✍ To erase the entered phone number digit

by digit:

Press the [4] button on the remote

controller.

Make a call

• Press the [VOL] knob.

• Press the [DIRECT] button on the remote

controller.

⁄

• You can input max 32 digits.

22 DPX-U6120/ DPX-U5120/ DPX-MP3120

Display of Phone Number type

(category)

The category items in the Phone Book are displayed

as follows:

Display

Information

“General”/“

”

General

“Home”/“

“Office”/“

“Mobile”/“

“Other”/“

”

Home

Office

Mobile

Other

”

English

Display Settings

Display Setting

You can select following Display Setting items.

Select the source

Press the [SRC] button.

DISP

SRC

Enter Function setting mode

Press the [VOL] knob.

4 ¢

VOL

Enter Display Setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings”/ “SETTINGS” > “Display &

Illumination”/ “DISP & ILLUMI”.

Function of DPX-U6120

Display type select

Press the [DISP] button.

Select the Function item

Turn the [VOL] knob and press it when the

desired item is displayed.

DPX-U6120

Mode

Display Type

4-line display mode Displays 3 to 4 lines of text.

3-line display mode Displays 2 to 3 lines of text.

Clock display mode Displays the clock.

Spectrum analyzer Displays a line of text and the spectrum analyzer.

display mode

Display off mode Turns off the display. Turns on temporarily when

you perform an operation.

Display

“Settings”

“Display &

Illumination”

Overview

Making Display and Illumination settings.

⁄

“Display Select” Selecting and customizing the Display type.

“Color Select” Selecting the Illumination Color of the panel.

Refer to <Illumination Color Selection>

• When the 4-line/3-line display mode is selected, the status

(ON/OFF indicator of each function) can be displayed on

the first line, and the icon of the currently selected source

and the text information title can be displayed on the left

side by the following <Information display setting> (page

25) operation.

(page 28).

“DISP & ILLUMI When Display off mode is selected in <Display

OFF”

type select> (page 24), sets whether to turn off

display only or display and key illumination.

“DISP&ILLUMI” / “DISP”

Status display: Select “Settings” > “Display & Illumination >

“Display Select” > “Status”

Side display: Select “Settings” > “Display & Illumination” >

“Display

Dimmer”

Reduces the display Illumination brightness.

“Auto”: Dims the illumination in conjunction

with the Light switch of the vehicle.

“Manual1”: Dims the illumination constantly.

“Manual2”: Dims the illumination darker than

Manual1.

“Display Select” > “Side Select”

“OFF”: Does not dim the illumination.

“Contrast”

“DISP N/P”

Adjusting the display contrast.

“1” - “5” - “12”

Switches the panel display between positive

or negative.

“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”

Sets the method of scroll to view hidden text.

“Auto” : Scrolls.

“Text Scroll”

“Once” : Scrolls once.

“OFF” : Does not scroll.

“BT DVC

STATUS”

You can display the connection status, signal

strength, and battery level.

: Battery level of cell-phone.

: Signal strength of cell-phone.

24 DPX-U6120/ DPX-U5120/ DPX-MP3120

“ILLUMI

Dimmer”

Reduces the key Illumination brightness.

“Auto”: Dims the illumination in conjunction

with the Light switch of the vehicle.

“Manual1”: Dims the illumination constantly.

“Manual2”: Dims the illumination darker than

Manual1.

Text scroll

Press the [DISP] button for at least 1 second.

The displayed text scrolls.

Function of DPX-U6120

“OFF”: Does not dim the illumination.

Information display setting

“ILLUMI Effect” Sets whether the key illumination brightness is

changed in conjunction with the key operation.

“ON”/ “OFF”

“ILLUMI MSC Sets whether the key illumination color is

SYNC”

You can customize the display of the Spectrum

analyzer display mode.

Select the source

Press the [SRC] button.

changed in conjunction with the sound volume.

“ON”/ “OFF”

(

: Factory setting)

Enter Function setting mode

Press the [VOL] knob.

DPX-U5120 DPX-MP3120

Enter the Display Setting mode and select the

Spectrum analyzer display mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Display

“SETTINGS”

“DISP & ILLUMI”

Overview

Making Display and Illumination settings.

“COLOR SELECT” Selecting the Illumination Color of the panel.

Refer to <Illumination Color Selection>

(page 28).

Select “Settings” > “Display & Illumination” >

“Display Select”.

“TEXT SCROLL” Sets the method of scroll to view hidden text.

“AUTO” : Scrolls.

Select the setting item to adjust

Turn the [VOL] knob and press it when the

desired item is displayed.

“ONCE” : Scrolls once.

“OFF” : Does not scroll.

“DISP OFF

MODE”

Sets the clock and button illumination when

“DISP OFF MODE”is selected as described in

<Text Display Selection> (page 27).

“ON” : Displays the clock.

“OFF” : Dims the clock.

Display

“Display Select”

Setting

“Side Select” Sets the side part display for 4-line display mode

and 3-line display mode.

“CLOCK”

Text/ Icon/ Disappear

Sets the spectrum analyzer display for Spectrum

analyzer display mode.

“KEY ILLUMI” “ON” : Turns on the button illumination.

“OFF” : Dims the button illumination.

“Graphic

Select”

“DISP DIMMER” Reduces the display Illumination brightness.

“AUTO”: Dims the illumination in conjunction

with the Light switch of the vehicle.

Spectrum analyzer A/ Spectrum analyzer B /

Spectrum analyzer&Text

“Clock Select” Sets the Clock display for Clock display mode.

“MANUAL1”: Dims the illumination constantly.

“MANUAL2”: Dims the illumination darker

than Manual1.

Home/ Home&Sub

“Status”

Sets the status display (ON/OFF indicator for each

function) for 4-line display mode and 3-line display

mode.

“OFF”: Does not dim the illumination.

“ILLUMI

DIMMER”

Reduces the key Illumination brightness.

“AUTO”: Dims the illumination in conjunction

with the Light switch of the vehicle.

“MANUAL1”: Dims the illumination constantly.

“MANUAL2”: Dims the illumination darker

than Manual1.

Appear/ Disappear

Make a setting

Turn the [VOL] knob.

Exit Function setting mode

Press the [ ] button for at least 1 second.

“OFF”: Does not dim the illumination.

(

: Factory setting)

⁄

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

• To adjust the “Sub time” with “Home & Sub” selected for

“Clock Select”, select a city in advance using the <Dual clock

city setting> (page 29) function.

Exit Function setting mode

Press the [ ] button for at least 1 second.

English

Display Settings

Function of DPX-U6120

In Music CD source

Selecting text display

Disc title (“Disc Title”)

Track title (“Track Title”)

Play time (“P-Time”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Changes displayed information on each of the

following sources:

Blank (“Blank”)

Select the source

Press the [SRC] button.

In Auxiliary input source

Source name (“Source Name”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

Enter Function setting mode

Press the [VOL] knob.

Select Text display selection mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “Display & Illumination” >

“Display Select” > “Text Select”.

In Standby

Source name (“Source Name”)

Clock (“Clock”)

Date (“Date”)

Blank (“Blank”)

In Bluetooth audio source

4-line display mode

4 Select the text display part

Turn the [VOL] knob.

The selected text display part blinks.

Bluetooth audio (“Source Name”) Spectrum analyzer & Clock

Song title* (“Song Title”)

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

Artist name* (“Artist Name”)

Album name* (“Album Name”)

5 Select the text

Press the [4] or [¢] button

3-line display mode

Exit Function setting mode

Press the [ ] button for at least 1 second.

Bluetooth audio (“Source Name”) Spectrum analyzer & Clock

Title & Artist* (“Title/Artist”)

Album & Artist* (“Album/Artist”)

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

In FM Tuner source

Frequency (“Frequency”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

* Function of KCA-BT300

In Disc changer source (Optional)

In AM Tuner source

Disc title (“Disc Title”)

Track title (“Track Title”)

Play time (“P-Time”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Frequency (“Frequency”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

In USB/ iPod/ Audio file source

4-line display mode

Song title (“Song Title”)

Play time (“P-Time”)

Album name (“Album Name”)

Artist name (“Artist Name”)

Folder name (“Folder Name”)

File name (“File Name”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

3-line display mode

Title & Artist (“Title/Artist”)

Album & Artist (“Album/Artist”)

Folder name (“Folder Name”)

File name (“File Name”)

Spectrum analyzer & Clock

(“Speana/Clock”)

Date (“Date”)

Blank (“Blank”)

Play time (“P-Time”)

26 DPX-U6120/ DPX-U5120/ DPX-MP3120

Function of DPX-U5120/ DPX-MP3120

⁄

Text Display Selection

• Setting is available when the 4-line display mode, 3-line

display mode, Clock display mode, or Spectrum analyzer

display (Spectrum analyzer&Text type) mode which allows

text display. Refer to <Display type select> (page 24).

• If the selected display item does not have any information,

alternative information is displayed.

Changing displayed information on each source

following;

Press the [DISP] button.

In Tuner source

• Some items cannot be selected depending on the display

type and row.

• When selecting “Folder Name” while playing with iPod,

names will be displayed depending on currently selected

browsing items.

• If the iPod Control by Hand Mode is set to on while playing

the iPod, “iPod by Hand Mode” is displayed.

• If all characters cannot be displayed while playing with iPod,

the file number in the list is displayed.

Information

Frequency

Display off

Display

“FREQUENCY”

“DISP OFF MODE”

In CD source

Information

Disc title

Track title

Play time & Track number

Display off

Display

“DISC TITLE”

“TRACK TITLE”

“P-TIME”

Information

Music title

Folder name

File name

Display

“DISP OFF MODE”

“TITLE***”

“FLD***”

“FILE***”

In Audio file/ iPod source

Information

Display

Music title & Artist name

Album name & Artist name

Folder name

File name

Play time & Music number

Display off

“TITLE/ARTIST”

“ALBUM/ARTIST”

“FOLDER NAME”

“FILE NAME”

“P-TIME”

“DISP OFF MODE”

In Standby/ Auxiliary input source

Information

Source name

Display off

Display

“SOURCE NAME”

“DISP OFF MODE”

⁄

• When you select the Display off mode, the display setting of

each source will be changed to the Display off.

• If the selected display item does not have any information,

alternative information is displayed.

• When selecting “FOLDER NAME” while playing with iPod,

names will be displayed depending on currently selected

browsing items.

• If all characters cannot be displayed while playing with iPod,

the file number in the list is displayed.

Information

Music title

Folder name

File name

Display

“TITLE***”

“FOLDER***”

“FILE***”

English

Display Settings

Illumination Color Selection

Auxiliary Input Display Setting

Selecting the Illumination Color of the panel.

Selecting the display when changing to Auxiliary

input source.

Enter Function setting mode

Press the [VOL] knob.

Select the AUX source

Press the [SRC] button.

Select the “AUX” display.

Enter Illumination color selection mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Enter Function setting mode

Press the [VOL] knob.

Select “Settings”/ “SETTINGS” > “Display &

Illumination”/ “DISP & ILLUMI” > “Color Select”/

“COLOR SELECT”.

Enter Auxiliary input display setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the place where you want to set the

Illumination Color

Turn the [VOL] knob and press it when the

Select “Settings”/ “SETTINGS” > “AUX Name

Set”/ “AUX NAME SET”.

desired item is displayed.

Select the Auxiliary input display

Turn the [VOL] knob.

Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or

Place

Display

Display and key

“All”/“ALL”

Display

Key

“Display”/“DISPLAY”

“Key”/“KEY”

“Knob”

“TV”

Exit Function setting mode

Press the [ ] button for at least 1 second.

Volume knob (DPX-U6120 only)

Select the Illumination Color

Turn the [VOL] knob and press it when the

⁄

• The Auxiliary input display can be set only when the built-in

auxiliary input or the auxiliary input of optional KCA-S220A

is used. On the KCA-S220A, “AUX EXT” is displayed by

default.

desired item is displayed.

Select the color from “Variable Scan”/ “VARIABLE

SCAN”, “Color1”/ ”COLOR1” — “Color24”/ ”COLOR24”,

or “User”/ “USER”.

Creating “User”/”USER” color

You can create your original color during the

selection from “Color1”/ ”COLOR1” — “Color24”/

”COLOR24”.

The color you created can be called when you

select “User”/ “USER”.

1. Press the [VOL] knob for at least 1 second.

Enter the detail color adjustment mode.

2. Set the color.

Operation type

Operation

To select the color to adjust. Press the [4] or [¢] button.

(red, green, or blue)

To adjust color.

(Range: 0 – 9)

Turn the [VOL] knob.

3. Press the [VOL] knob.

Exit the detail color adjustment mode.

Exit Function setting mode

Press the [ ] button for at least 1 second.

28 DPX-U6120/ DPX-U5120/ DPX-MP3120

Clock and Other Functions

Adjusting Date

1. Turn the [VOL] knob to adjust the year.

2. Press the [VOL] knob.

3. Turn the [VOL] knob to adjust the month.

4. Press the [VOL] knob.

5. Turn the [VOL] knob to adjust the day.

6. Press the [VOL] knob.

SRC

Enter Date format mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Date Mode”.

DPX-U5120

DPX-MP3120

B.BOOST

4 ¢

VOL

Function of DPX-U6120

Select Date format

Clock and Date Adjustment

Turn the [VOL] knob and press it when the

desired item is displayed.

Select from 7 types.

You can adjust the clock and date.

Display

Overview

Exit Function setting mode

Press the [ ] button for at least 1 second.

“Settings”

“Clock & Date”

“Clock Adjust”

“City Select”

Sets the clock.

Sets the two cities to be displayed when

“Home&Sub type”is selected for“Clock

Select”. Refer to <Information display

setting> (page 25), <Dual clock city

setting> (page 29).

Function of DPX-U6120

Dual clock city setting

You can select cities for two clocks.

“Sub Clock Adjust” Adjusts the time difference caused by

Enter Function setting mode

Press the [VOL] knob.

summer time.

“-1h” / “0h” / “+1h”

Advances the clock one hour when set

to ON.

“ON” / “OFF”

Sets the date.

Sets the date display mode.

“Summer Time”

Select City Select mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “Clock & Date” > City Select”

“Date Adjust”

“Date Mode”

(

: Factory setting)

3 Select the city (Home or Sub) display part

Turn the [VOL] knob.

Enter Function setting mode

Press the [VOL] knob.

The selected city display part blinks.

4 Set cities for Home/ Sub

Enter Clock adjustment mode

Turn the [VOL] knob and press it when the

Press the [4] or [¢] button

desired item is displayed.

Select “Settings” > “Clock & Date” > “Clock

Adjust”.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

Adjusting Clock

1. Turn the [VOL] knob to set the hours.

2. Press the [¢] button.

3. Turn the [VOL] knob to set the minutes.

4. Press the [VOL] knob.

• To display the clocks of two cities, select “Home&Sub” type

for “Clock Select” described in <Information display setting>

(page 25).

• For adjustment of Home time, refer to <Clock and Date

Adjustment> (page 29).

• Time of Sub City is automatically derived from Home time.

When summer time systems are different between Home

and Sub cities, adjustment can be done by referring to “Sub

Clock Adjust” of <Clock and Date Adjustment> (page 29).

Enter Date adjustment mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Date Adjust”.

English

Clock and Other Functions

Function of DPX-U5120/ DPX-MP3120

“Beep”/“KEY

BEEP”

Setting the operation check sound (beep sound)

ON/OFF.

“ON”/ “OFF”

When this is set to ON, the following character

strings are displayed in Chinese:

Folder name/ File name/ Song title/ Artist

name/ Album name/ KCA-BT300/BT200

(optional accessory)

Clock Adjustment

You can adjust the clock and date.

“Chinese”*

Enter Clock adjustment mode

Press the [B.BOOST] button for at least 1

second.

“ON”/ “OFF”

The hour display blinks.

“Built in AUX”/ When this is set to ON, AUX source can be

“BUILT-IN AUX” selected.

Adjust the hour

Turn the [VOL] knob to adjust the hour, and

then press the [VOL] knob.

The minute display blinks.

“ON”: Allows AUX source to be selected. Use

this setting when the built-in AUX terminal

is connected to the external equipment all

the time.

“OFF”: Disable AUX source selection. Use this

setting when the built-in AUX terminal is

not used.

Adjust the minute

Turn the [VOL] knob to adjust the minute, and

then press the [VOL] knob.

Finish the Clock Adjustment.

“Forced CD-DA”/ Sets the CD read mode.

“CD READ”

“Settings 1”/”1”: Automatically distinguishes

between Audio file disc and music CD when

playing disc.

Initial Settings

“Settings 2”/”2”: Forces playing as music CD.

You can select the following Initial Setting items.

“Built in AMP”* Selecting“OFF”turns off the built-in amplifier.

Turning off the built-in amplifier improves the

quality of the sound from Preout.

Select the Standby

Press the [SRC] button.

“ON”/ “OFF”

Switches the preout between rear output and

Select the “STDBY”/ “STANDBY” display.

“Switchable

Preout”/“SWITCH subwoofer output.

PREOUT” “Rear”/ “REAR”: Rear output

“SubWoofer”/ “SUB-W”: Subwoofer output

“SP SELECT”** Fine-tuning so that the System Q value is

optimal when setting the speaker type as

follows;

Enter Function setting mode

Press the [VOL] knob.

Enter Initial Setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Initial Settings”/ “INITIAL SET”.

“SP OFF”: Off

“SP 5/4”: For 5 & 4 in. speaker

“SP 6*9/6”: For 6 & 6x9 in. speaker

“SP OEM”: For the OEM speaker

Select the setting item to adjust

Turn the [VOL] knob.

“System F/W

Upgrades the firmware.

Display

“Initial Settings”/

“INITIAL SET”

“Source Select”* Sets the source selection method.

Select“2”to change the source selection

method. Press the [SRC] button, turn the [VOL]

knob to select the source, and then press the

[VOL] knob to determine it.

Overview

Update”/“F/W Selecting“YES”and then pressing [VOL] knob

UP”

starts upgrading the firmware.

For how to update the firmware, access our web

site. http://www.kenwood.com/cs/ce/

(

: Factory setting)

* Function of DPX-U6120

** Function of DPX-U5120/DPX-MP3120

“Settings 1”/ “2”

“Tuner Preset

Sets the Tuner preset type.

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

Type”/“PRESET “Type Normal”/ “TYPE NORMAL”: 1 station

TYPE”

can be assigned to 1 preset button in each

of 4 bands (FM1, FM2, FM3, and AM), i.e.,

a total of 24 stations (6 stations x 4 bands)

can be preset.

“Type Mixed”/ “TYPE MIXED”: A total of 6

stations can be assigned to a total of 6 preset

buttons regardless of band (FM1, FM2, FM3,

and AM). You can recall a preset station

without switching between bands.

Exit Function setting mode

Press the [ ] button for at least 1 second.

30 DPX-U6120/ DPX-U5120/ DPX-MP3120

Demonstration mode Setting

Muting volume upon reception of

Phone call

Turning the demonstration mode ON/OFF.

The audio system automatically mutes upon

reception of an incoming call.

Enter Function setting mode

Press the [VOL] knob.

Enter Demonstration mode setting

Turn the [VOL] knob and press it when the

desired item is displayed.

When a call comes in

“CALL” is displayed.

The audio system pauses.

Select “DEMO Mode”/ “DEMO MODE”.

Listening to the audio during a call

Press the [SRC] button.

The “CALL” display disappears and the audio system

Set the Demonstration mode

Turn the [VOL] knob and press it when the

desired item is displayed.

comes back ON.

Select “ON” or “OFF”.

When the call ends

Hang up the phone.

The “CALL” display disappears and the audio system

Exit Function setting mode

Press the [ ] button for at least 1 second.

comes back ON.

⁄

• To use the TEL Mute feature, you need to hook up the MUTE

wire to your telephone using a commercial telephone

accessory. Refer to <Connecting Wires to Terminals> (page

53).

English

Function of DPX-U6120

Audio Adjustments – DPX-U6120 –

“Volume offset” Sets each source’s volume as a difference from

the basic volume.

“–8” — “ 0” (AUX: “-8”— “+8”)

“2Zone”

“2Zone Select”

“Preset”

Sets the Dual Zone System.

- <Dual Zone System> (page 35).

Sets the audio preset.

- <Audio Preset Memory> (page 39).

- <Audio Preset Recall> (page 39).

SRC

(

: Factory setting)

4 ¢

VOL

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Audio Control

Enter Function setting mode

Press the [VOL] knob.

You can adjust the following Audio Setting items.

Display

“Audio Control”

“SubWoofer Level” You can set subwoofer level.

Overview

Enter Audio Control mode

Turn the [VOL] knob and press it when the

desired item is displayed.

“–15” — “0” — “+15”

Select “Audio Control”.

“DSP Set”

“Bypass”: Disables the DSP function.

“Through”: Enables the DSP function.

Sets the sound quality.

- <Preset Equalizer curve Select> (page 33).

- <Manual Equalizer Control> (page 33).

Sets the Bass Boost level in two steps.

“OFF”/ “Step1” – “2”

Select the setting item to adjust

Turn the [VOL] knob and press it when the

desired item is displayed.

“Equalizer”

“Bass Boost”

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

“HIGHWAY-SOUND” Compensates the low volume or bass sound

being lost by road noises to make vocal sound

clearer.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Unavailable when the tuner source is selected.

“OFF”/ “Step1”/ “2”/ “3”

Turns ON/OFF the Supreme plus function.

Can be set while Music CD source, Audio file

source of USB and iPod source.

Remarks

• DSP Set

“Supreme+”

“Position”

When “DSP Set” is set to “Bypass”, the DSP function is

disabled , and the colored items can not be set.

“ON”/ “OFF”

Compensates the sound environment in

accordance with the listening position.

- <Listening Position Selection> (page 34).

- <Listening Position Fine Adjustments>

(page 34).

• HIGHWAY-SOUND

Increases the volume of faintest sound being lost by road

noises to make the sound more audible. Additionally, it

accentuates bass sound being lost by road noises to make

the bass sound more dynamic.

“Balance”

“Fader”

Adjusts left/right speaker balance.

(Left) “L15” — “0” — “R15” (Right)

Adjusts front/rear speaker balance.

(Rear) “R1”5 — “0” — “F15” (Front)

• Supreme+ (Supreme Plus)

Technology to extrapolate and supplement with

proprietary algorithm, the high-frequency range that is cut

off when encoding. The bass and vocal sound that are cut

off by encoding are supplemented for the reproduction

of natural sound quality. Supplementing is optimized by

compression format (AAC, MP3 or WMA) and processed

according to bit rate. The effect is negligible with music

that is encoded at high bit rate, variable bit rate or has

minimal high frequency range.

“2Zone Rear Volume” Refer to <Dual Zone System> (page 35).

“SubWoofer”

Turns on/off the subwoofer output.

“ON”/ “OFF”

“Detailed Setup”

“Car Type”

“Speaker Setting”

“Car Type Adjust”

“X'Over”

To get clear sound, set the sound environment

according to the location and size of physically

installed speakers with reference to the

followings:

- <Car Type Selection> (page 37).

- <Speaker Setting> (page 37).

- <Car Type Fine Adjustments> (page 38).

- <X’Over Setting> (page 38).

The bass and vocal sound of Music CD/ iPod is also

supplemented.

• Dual Zone System

Main source and sub source (Auxiliary input) output Front

channel and Rear channel separately.

32 DPX-U6120/ DPX-U5120/ DPX-MP3120

Preset Equalizer curve Select

Manual Equalizer Control

You can select the following Equalizer curve.

You can adjust the following Equalizer Control

items.

Display

“Natural”

“User”

Equalizer curve

Natural

User*

Band

Item

Range

“BAND1”(62.5 Hz) “GAIN”Band level

“EFCT”Bass Effect

“BAND2”(250 Hz) “GAIN”Band level

-9 –+9 dB

“ON”/“OFF”

-9 –+9 dB

: Factory setting)

“Rock”

“Pops”

“Easy”

Rock

Pops

Easy

“BAND3”(1 kHz)

“BAND4”(4 kHz)

“GAIN”Band level

“Top 40”

“Jazz”

Top 40

Jazz

“BAND5”(16 kHz) “GAIN”Band level

“Game”

“iPod”

Game

(

iPod (During iPod source only)

Select the source

Press the [SRC] button.

* The Equalizer curve set in the section <Manual Equalizer

Control> is recalled.

Select a source other than “STDBY”.

(

: Factory setting)

Enter Function setting mode

Press the [VOL] knob.

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Enter Manual Equalizer Control mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Equalizer” > “Manual

Equalizer”.

Enter Function setting mode

Press the [VOL] knob.

Enter Preset Equalizer mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select the item you want to set

Select “Audio Control” > “Equalizer” >

“Preset Equalizer”.

Operation type

Selects the item.

Adjust each item.

Set the value.

Operation

Turn the [VOL] knob.

Press the [

Press the [VOL] knob.

4] or [¢] button.

Select the Equalizer curve

Turn the [VOL] knob.

✍ Select the iPod Equalizer curve

You can select from 22 Equalizer curve types for

iPod when “iPod” is selected.

1. Enter iPod Equalizer mode

Press the [VOL] knob.

2. Select the iPod Equalizer curve

Turn the [VOL] knob and press it when the

desired item is displayed.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• When “iPod” is selected in the section <Preset Equalizer

curve Select> (page 33), Manual Equalizer Control is disabled.

• You can select for each source.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• You can select for each source.

English

Function of DPX-U6120

Audio Adjustments – DPX-U6120 –

Listening Position Selection

Listening Position Fine Adjustments

The sound environment can be compensated in

accordance with the selected position. According to

the listening position, select the position from the

Making fine adjustment of the value specified at

Preset position selection per speaker.

Select the source

Press the [SRC] button.

following settings.

Select a source other than “STDBY”.

Compensation seat

Not compensating.

Front-Left seat

Front-Right seat

Front seat

Display

“All”

“Front-Left”

“Front-Right”

“Front”

Enter Function setting mode

Press the [VOL] knob.

Enter Manual position setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

(

: Factory setting)

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Select “Audio Control” > “Position” > “DTA”.

Select the speaker you want to set

Turn the [VOL] knob and press it when the

desired value is displayed.

Enter Function setting mode

Press the [VOL] knob.

Item

“Front”

“L”

“R”

“Rear”

“L”

“R”

“Subwoofer”

“L”

“R”

“Initialize”

Setting overview

Enter Preset position setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Position” > “Preset

Position”.

Front Left speaker

Front Right speaker

Rear Left speaker

Rear Right speaker

Select the seat you want to compensate

Turn the [VOL] knob.

Subwoofer Left

Subwoofer Right

Initialize the setting values.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Set the value

Press the [4] or [¢] button

Adjust between 0 and 170 cm.

Exit Function setting mode

Press the [ ] button for at least 1 second.

34 DPX-U6120/ DPX-U5120/ DPX-MP3120

Dual Zone System

Main source and sub source (Auxiliary input) output

Front channel and Rear channel separately.

Display

Overview

“2Zone Rear Volume”* Adjust the volume of Rear channel.

“0” — “35”

“Detailed Setup”

“2Zone”

Sets the Dual Zone System.

“ON”/ “OFF”

“2Zone Select”*

Specifies the destination of sub source sound

when the Dual Zone function is turned on.

“Rear”/ “Front”

* The Dual Zone System is set to “ON”.

(

: Factory setting)

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Enter Function setting mode

Press the [VOL] knob.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Detailed Setup”.

Select the item you want to set

Turn the [VOL] knob and press it when the

desired item is displayed.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• Select Main source by [SRC] button.

• Adjust the volume of Front channel by [VOL] knob.

• The Audio Control has no effect on sub source.

• There are following limitations when Dual Zone System is

enabled.

- There is no output from the subwoofer.

- “Fader”,“SubWoofer Level”of <Audio Control> (page 32) and

DSP function are not available.

• The Bluetooth audio source can be set exclusively to the

front speaker. Set “2Zone Select” to “Rear”.

English

Function of DPX-U5120/ DPX-MP3120

Audio Adjustments – DPX-U5120/ DPX-MP3120 –

“DETAILED SET”

“LPF

SUBWOOFER”

Selects cut off frequency of subwoofer output.

“85”/ “120”/ “160”/ “THROUGH” (OFF) Hz

“SUB-W PHASE” Selects the phase of subwoofer output.

“REVERSE” (180°)/ “NORMAL” (0°)

“SUPREME SET” Turns on/off the supreme function.

Can be set while Audio file source of CD/USB

(excluding iPod).

SRC

“ON”/ “OFF”

Sets each source’s volume as a difference from

the basic volume.

VOL

“VOLUME

OFFSET”

“–8” — “0” (AUX: “–8” — “0” — “+8”)

Audio Control

(

: Factory setting)

You can adjust the following Audio Setting items.

Select the source

Press the [SRC] button.

Display

Overview

Select a source other than “STANDBY”.

“AUDIO CONTROL”

“SUBWOOFER SET” Turns on/off the subwoofer output.

Enter Function setting mode

Press the [VOL] knob.

“OFF”/ ”ON”

“SYSTEM Q”

Switches between the following preset

equalizer curves.

Enter Audio Control mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “AUDIO CONTROL”.

“NATURAL”/ “USER”/ “ROCK”/ “POPS”/

“EASY”/ “TOP40”/ “JAZZ”/ “GAME”

For USER: This appears when Bass level,

Middle level, and Treble level are

adjusted.

Select the setting item to adjust

Turn the [VOL] knob and press it when the

desired item is displayed.

“BASS ADJUST”

“BASS FREQ”

You can set bass for each source.

Bass Center Frequency

40/50/60/70/80/100/120/150 (Hz)

Bass level

“–8” — “0” — “+8”

Bass Q Factor

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

“BASS LEVEL”

“BASS Q”

1.00/1.25/1.50/2.00

Bass Extend

Exit Function setting mode

Press the [ ] button for at least 1 second.

“BASS EXT”

”ON”/ “OFF”

“MID ADJUST”

“MID FREQ”

You can set middle for each source.

⁄

Middle Center Frequency

0.50/1.00/1.50/2.00 (kHz)

Middle level

“–8” — “0” — “+8”

Middle Q Factor

1.00/2.00

You can set treble for each source.

Treble Center Frequency

10.0/12.5/15.0/17.5 (kHz)

Treble level

• The “SUB-W PHASE” item can be made when a setting other

than “THROUGH” is selected for the “LPF SUBWOOFER” item.

“MID LEVEL”

“MID Q”

Remarks

• Supreme

Technology to extrapolate and supplement with

proprietary algorithm, the high-frequency range that is

cut off when encoding at low bit rate (less than 128Kbps,

Sampling frequency is 44.1kHz).

Supplementing is optimized by compression format (MP3,

WMA and AAC) and processed according to bit rate. The

effect is negligible with music that is encoded at high bit

rate, variable bit rate or has minimal high frequency range.

“TRE ADJUST”

“TRE FREQ”

“TRE LEVEL”

“BALANCE”

“–8” — “0” — “+8”

Adjusts left/right speaker balance.

(Left)“L15” — “0” — “R15” (Right)

Adjusts front/rear speaker balance.

(Rear)“R15” — “0” — “F15” (Front)

You can set subwoofer level.

“–15” — “0” — “+15”

“FADER”

“SUB-W LEVEL”

36 DPX-U6120/ DPX-U5120/ DPX-MP3120

Function of DPX-U6120

DSP Setup

Speaker Setting

The speaker X’Over is automatically set when the

position and size of each speaker are selected from

the following items.

Speaker

Item

Range

“Front”

“SIZE”

Speaker Size Front

SRC

“O.E.M.”, “10cm”, “13cm”, “16cm”,

“17cm”, “18cm”, “4x6”, “5x7”, “6x8”,

“6x9”, “7x10”

4 ¢

VOL

“LOCATION” Speaker Location Front

“Door”, “On Dash”, “Under Dash”

“TWEETER” Speaker Size Tweeter

“None”, “Use”

Speaker Size Rear

“None”, “O.E.M.”, “10cm”, “13cm”,

“16cm”, “17cm”, “18cm”, “4x6”, “5x7”,

“6x8”, “6x9”, “7x10”

Car Type Selection

“Rear”

“SIZE”

You can compensate the delay of the sound arrival

time by selecting your environment from the

following car types.

“LOCATION” Speaker Location Rear

Display

Overview

• “Door”, “Rear Deck”

“OFF”

Not compensating.

Compact car

Full size car

Station wagon

Minivan

Sport-utility vehicle

Long Minivan

• “2nd Row”, “3rd Row” (Car Type:

“Minivan”, “Minivan (Long)”)

“Compact”

“Full size car”

“Wagon”

“Minivan”

“SUV”

“SubWoofer” “SIZE”

Speaker Size Subwoofer

“None”, “16cm”, “20cm”, “25cm”,

“30cm”, “38cm Over”

(

: Factory setting)

“Minivan (Long)”

Select the source

(

: Factory setting)

Press the [SRC] button.

Select a source other than “STDBY”.

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Enter Function setting mode

Press the [VOL] knob.

Enter Function setting mode

Press the [VOL] knob.

Enter Speaker setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Detailed Setup” >

“Speaker Setting”.

Enter Cabin select mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Detailed Setup” >

“Car Type”.

Select the item you want to set

Operation type

Selects the item.

Adjust each item.

Set the value

Operation

Turn the [VOL] knob.

Select the car type

Turn the [VOL] knob to select the car type, and

then press the [VOL] knob.

Press the [

Press the [VOL] knob.

4] or [¢] button.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• You can compensate the distances in more details by using

<Car Type Fine Adjustments> (page 38) function.

English

Function of DPX-U6120

DSP Setup

Reference point

Car Type Fine Adjustments

Adjusting fine tuning of the speaker position

compensation value specified at <Car Type

Selection> (page 37).

+100cm

FRONT

REAR

Display

“FRONT”

“REAR”

“SW”

Item

Range

50cm

Front speaker

Rear speaker

Subwoofer

0 – 440 cm

80cm

REAR

+70cm

(

: Factory setting)

150cm

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

+0cm

SUB-W

Enter Function setting mode

Press the [VOL] knob.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Enter Car Type Adjustment mode

Turn the [VOL] knob and press it when the

desired item is displayed.

X’Over Setting

Select “Audio Control” > “Detailed Setup” >

“Car Type Adjust”.

Fine adjusting the following setting values

corresponding to the X’Over values set in the

section <Speaker Setting> (page 37).

Select the item you want to set

Operation type

Selects the item.

Adjust each item.

Set the value

Operation

Turn the [VOL] knob.

Display

Item

Range

Press the [

Press the [VOL] knob.

4] or [¢] button.

“X’Over”

“Front”

“FC”

Front High Pass Filter

Through, 30, 40, 50, 60, 70, 80, 90,

The settings of the delay time are automatically

identified and compensated by specifying the

distances of each speaker from the center of the

vehicle interior.

1 Set the front and rear positions and the height

of the reference point to the position of the ears

of the person sitting in the front seat, and set

the right and left positions to the center of the

vehicle interior.

2 Measure the distances from the reference point

to the speakers.

3 Calculate the distance difference in accordance

with the farthest speaker.

100, 120, 150, 180, 220, 250 (Hz)

“SLOPE” Front High Pass Slope

-6, -12, -18, -24 dB/Oct

Rear High Pass Filter

Through, 30, 40, 50, 60, 70, 80, 90,

100, 120, 150, 180, 220, 250 (Hz)

“Rear”

“FC”

“SLOPE” Rear High Pass Slope

-6, -12, -18, -24 dB/Oct

Subwoofer Low Pass Filter

30, 40, 50, 60, 70, 80, 90, 100, 120,

150, 180, 220, 250, Through (Hz)

“SubWoofer” “FC”

“SLOPE” Subwoofer Slope

-6, -12, -18, -24 dB/Oct

“PHASE” Subwoofer Phase

Reverse (180°)/ Normal (0°)

(

: Factory setting)

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Enter Function setting mode

Press the [VOL] knob.

Enter X’Over setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

38 DPX-U6120/ DPX-U5120/ DPX-MP3120

When you press the Reset, all the sources will be the setting

value which is registered.

• Preset number “1” and “2”:

Select “Audio Control” > “Detailed Setup” >

“X’Over”.

Select the speaker you want to set

Turn the [VOL] knob and press it when the

desired item is displayed.

The memory cannot be erased by the Reset button.

• This function cannot be registered when the iPod Equalizer

set in <Preset Equalizer curve Select> (page 33).

Select “Front”, “Rear”, or “SubWoofer”.

Audio Preset Recall

Select the item you want to set

Recalling the sound setup registered by <Audio

Preset Memory> (page 39).

Operation type

Selects the item.

Adjust each item.

Set the value

Operation

Turn the [VOL] knob.

Press the [

Press the [VOL] knob.

4] or [¢] button.

Select the source

Press the [SRC] button.

Select a source other than “STDBY”.

Repeat steps 4 to 5 to complete the X’Over

settings.

Enter Function setting mode

Press the [VOL] knob.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Enter Audio preset recall mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Detailed Setup” >

“Preset” > “Preset Recall”.

Audio Preset Memory

Registering the value setup by Sound Control.

Setup Sound Control

Refer to the following operations to setup the

Sound Control.

- <Car Type Selection> (page 37)

- <Speaker Setting> (page 37)

- <Car Type Fine Adjustments> (page 38)

- <X’Over Setting> (page 38)

- <Manual Equalizer Control> (page 33)

- <Listening Position Selection> (page 34)

- <Listening Position Fine Adjustments> (page 34)

Select the number to recall in the memory

Turn the [VOL] knob and press it when the

desired item is displayed.

Select preset number.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “YES”.

“Recall Completed” is displayed.

Exit Function setting mode

Press the [ ] button for at least 1 second.

Enter Audio preset memory mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Audio Control” > “Detailed Setup” >

“Preset” > “Preset Memory”.

⁄

• The “User” of <Preset Equalizer curve Select> (page 33) is

changed to the value which was recalled.

• The Equalizer curve is changed to the value which was

recalled by the selected source.

Select the number to put in the memory

Turn the [VOL] knob and press it when the

desired item is displayed.

Select a preset number.

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “YES”.

“Memory Completed” is displayed.

Exit Function setting mode

Press the [ ] button for at least 1 second.

⁄

• Register 6 patterns of Audio Preset Memory.

• Preset number “1”:

English

Function of DPX-U6120

Log Function

Log Function item lock

Locks the Log Function items to prevent them from

being deleted automatically.

1 Display the Log Function list

Press the [LOG] button.

2 Lock the Log Function item

VOL

LOG

Turn the [VOL] knob to select item, and then

press the [VOL] knob for at least 1 second.

Locked items are indicated with “ ”.

Performing this step again will unlock the locked

item.

Log Function recall

This unit automatically memorizes the previously

used functions and Function setting items, which

can easily be recalled.

3 Exit Log Function

Press the [

] button.

1 Display the Log Function list

Press the [LOG] button.

Deleting a Log Function item

2 Recall the desired function

Deletes Log Function items.

Turn the [VOL] knob to select Log Function

item, and then press the [VOL] knob.

Enter Function setting mode

Press the [VOL] knob.

Category display

“FM”

“AM”

“iPod”

“USB”

Function category

FM broadcast

AM broadcast

iPod music

2 Select the Log delete mode

Turn the [VOL] knob and press it when the

desired item is displayed.

USB music

CD music

Select “Settings” > “Log” > “Log Delete”

“CD”

3 Select the Log Function item to delete

Turn the [VOL] knob to select Log Function

item, and then press the [VOL] knob.

Selecting “All” deletes all Log Function. (exclude a

locked items.)

“INIT”

“SET”

“DISP”

“AUD”

“BT”

Initial setting item

Setting item

Display setting item

Audio control setting

Calling number

4 Turn the [VOL] to select “YES”, and then press

the [VOL] knob.

“Completed” is displayed.

Cancelling the Log Function recall

Press the [ ] button.

⁄

Exit Function setting mode

Press the [ ] button for at least 1 second.

•

Maximum of 15 recently used functions are logged. When this

limit is reached, they are deleted from the oldest.

Logged functions can be deleted. Refer to <Deleting a Log

Function item> (page 40).

Functions to be logged can be set by categories. Refer to

<Log Function category setting> (page 41).

Logged functions can be locked to avoid them being deleted.

Refer to <Log Function item lock> (page 40).

Stations are logged after 1 minutes of reception.

This timing can be changed. Refer to <Tuner Log Function

time setting> (page 41).

40 DPX-U6120/ DPX-U5120/ DPX-MP3120

Log Function category setting

Tuner Log Function time setting

Sets the function category to be logged.

You can set the timing to log the station by the

reception time.

Enter Function setting mode

Press the [VOL] knob.

Enter Function setting mode

Press the [VOL] knob.

2 Select the Log Function setting mode

Turn the [VOL] knob and press it when the

desired item is displayed.

2 Select the Tuner Log time set mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” >“Log” >“Log settings”

Select “Settings” >“Log” >“Tuner Log Time Set”

3 Set the category to be logged

3 Set the reception time for the timing to start

logging the station

Turn the [VOL] knob to select time (“10SEC”,

“30SEC”, “1MIN”, “2MIN”, or “5MIN”), and then

press the [VOL] knob.

Category display

“Tuner Log”

Setting category

Radio-related

“Data CD Log”

“iPod Log”

CD-related

iPod-related

“USB Log”

USB-related

“Phone Log”

“Function Log”

Call-related (KCA-BT200/BT300 only)

Function setting-related

Exit Function setting mode

Press the [ ] button for at least 1 second.

Turn the [VOL] knob to select category, and

then press the [VOL] knob.

Check-mark (“✔”) the category you want to register.

Exit Function setting mode

Press the [ ] button for at least 1 second.

English

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Bluetooth Setup

“Bluetooth HF/ You can specify output speakers for hands-free

Audio”

voice communication and Bluetooth audio

sound.

“Front”: Outputs voice from the front speakers.

“All”: Outputs voice from the front and rear

speakers.

“Call Beep”

You can output a beep from the speaker when

a call comes in.

“ON”: Beep is heard.

“OFF”: Beep is canceled.

4 ¢

LOG VOL

“BT F/W Update” Display the version of the firmware of this unit.

“Mic Gain”*

Adjust the sensitivity of the microphone for a

telephone call. Adjust the voice of caller. Setting

to“+”increases the voice volume.

“–3” – “0” – “+3”

Bluetooth Setting

You can select the following Bluetooth Setting

items.

“NR Level”*

Reduce the noises generated by surrounding

environment without changing the microphone

volume. Adjust the voice of caller when it is

not clear. Setting to“+”increases the noise

reduction.

1 Press the [LOG] button for at least 1 second.

Turn the [VOL] knob and press it when the

desired item is displayed.

“–3” – “0” – “+3”

Select “Settings”.

“Echo Cancel

Level“*

Adjust the level of echo cancellation. Setting to

“+”increases the echo cancel reduction.

“–2” – “0” – “+2”

Select the Setting item

Turn the [VOL] knob and press it when the

(

: Factory setting)

desired item is displayed.

* Function of KCA-BT300

Display

“Settings”

“PAIRING”

“Device

Overview

Make a setting

Turn the [VOL] knob to select a setting value,

and then press the [VOL] knob.

Refer to <Registering Bluetooth device>

(page 43).

Select a cell-phone or Bluetooth audio player

connection.

Registration”

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

“Phone

Selection”

Remarks

• “Auto Answer” (Setting the Time Interval for Automatic

Answer)

Refer to <Selecting the Bluetooth device You

Wish to Connect> (page 44).

“Audio Selection”

This function automatically answers (responds to) a call

after lapse of the preset time interval for automatic answer.

“OFF” : Does not answer the phone call automatically.

“0” : Automatically answers the phone call at once.

“1s” – “99s” : Automatically answers the phone call after

lapse of 1 – 99 seconds.

“Special Device Register a Bluetooth device (pairing).

Select”

Refer to <Registering Bluetooth device>

(page 43).

“Device Delete” Cancel registration of the Bluetooth device.

Refer to <Deleting a Registered Bluetooth

device> (page 45).

“SMS Download” Download a short message.

Refer to <Downloading the SMS> (page 47).

⁄

• If the time set in the cell-phone is shorter than that set in

the unit, the former will be used.

“Voice Tag”

Registers voice for voice recognition and voice

to select the Phone number category in Phone

book.

• This function does not work for call waiting.

• “Bluetooth HF/Audio” (Setting up the Voice Output

Speakers)

Select the speaker which is further from the microphone in

- <Adding aVoice Dialing Command> (page 46)

- <Setting a Voice Command for Category>

(page 46)

“Detailed Setup” Move to detailed item.

order to prevent howling or echoes.

“PIN Code Edit” Specify the PIN code required when registering

this unit using the Bluetooth device.

Refer to <Registering PIN Code> (page 44).

“Auto Answer” Answer a call automatically after lapse of the

preset time interval for automatic answer.

• “BT F/W Update” (Displaying the Firmware Version)

Display the version of the firmware of this unit.

For how to update the firmware, access our web site.

http://www.kenwood.com/cs/ce/bt/

“OFF”/ “0SEC” – “8SEC” – “99SEC”

42 DPX-U6120/ DPX-U5120/ DPX-MP3120

Select”.

Registering Bluetooth device

2. Enter Special device registration mode

Press the [VOL] knob.

A list is displayed.

To make your Bluetooth device (cell-phone) usable

with this unit, you need to register it (pairing). You

can register up to 5 Bluetooth devices to this unit.

3. Select a device name

Turn the [VOL] knob and push the center when

the desired device name is displayed.

If “Completed” is displayed, registration is

completed.

4. Go through the procedure step 3 of

<Registering from this unit> (page 43) and

complete the registration (pairing).

Cancelling Special device registration mode

Press the [ ] button for at least 1 second.

Registering from this unit

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Enter Bluetooth device registration mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “PAIRING” > “Device

Registration”.

Search for the Bluetooth device.

When search is completed, “Finished” is displayed.

⁄

• If the device name is not in the list, select “Other Phones”.

Select a Bluetooth device

Turn the [VOL] knob and press it when the

desired item is displayed.

Input the PIN code

Operation type

Operation

Select the numbers.

Move to the next digit.

Delete the last digit.

Turn the [VOL] knob.

Press the [

] button.

Transmit the PIN code

Press the [VOL] knob.

If “Pairing Success” is displayed, registration is

completed.

✍ If the error message appears even though the

PIN code is correct, try <Registering Special

Bluetooth device> (page 43).

Return to the device list

Press the [ ] button.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

• This unit allows up to eight digits to be input for a PIN code.

If a PIN code cannot be input from this unit, it can be input

from the Bluetooth device.

• If there are 5 or more Bluetooth devices registered, you

cannot register a new Bluetooth device.

Registering Special Bluetooth device

Allow registration of a special device that cannot be

registered normally (pairing).

1. Select Special device registration mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “PAIRING” > “Special Device

English

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Bluetooth Setup

Registering PIN Code

Selecting the Bluetooth device You

Wish to Connect

By operating the Bluetooth device, specify the PIN

code necessary for registering this unit.

When two or more Bluetooth devices have already

been registered, you need to select the Bluetooth

device you wish to use.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Enter PIN code edit mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “Detailed Setup” > “PIN

Code Edit”.

Select Bluetooth device selection mode

Turn the [VOL] knob and press it when the

desired item is displayed.

The current setting of PIN code is displayed.

Cell-phone

Input the PIN code

Select “Settings” > “PAIRING” > “Phone

Selection”.

Operation type

Operation

Select the numbers.

Move to the next digit.

Delete the last digit.

Turn the [VOL] knob.

Audio player

Select “Settings” > “PAIRING” > “Audio

Selection”.

Press the [

] button.

Enter Bluetooth device selection mode

Press the [VOL] knob.

“(name)” is displayed.

Press the [VOL] knob.

If “Completed” is displayed, registration is

completed.

Select the Bluetooth device

Turn the [VOL] knob.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

Set up the Bluetooth device

Press the [VOL] knob.

“✱(name)” or “-(name)” is displayed.

“✱”: The selected Bluetooth device is busy.

“-”: The selected Bluetooth device is on standby.

“ “ (blank): The Bluetooth device is deselected.

⁄

• By default, “0000” is specified.

• A PIN code can be specified with up to eight digits.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

• If a Bluetooth device is already selected, deselect it, and

then select a different one.

• If you cannot select a device using the audio player,

connect the device with the audio player.

44 DPX-U6120/ DPX-U5120/ DPX-MP3120

Deleting a Registered Bluetooth

device

Downloading the Phone Book

Download the phone book data from the cell-

phone to this unit so that you can use the Phone

Book of this unit.

You can delete a registered Bluetooth device.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

To download automatically

If the cell-phone supports a phone book

synchronization function, the phone book is

downloaded automatically after Bluetooth

connection.

Enter Bluetooth device deletion mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “PAIRING” > “Device Delete”.

“(name)” is displayed.

⁄

• Setting on the cell-phone may be required.

• If no phone book data is found in the unit even after

the compete display, your cell-phone may not support

automatic download of phone book data. In this case, try

downloading manually.

Select the Bluetooth device

Turn the [VOL] knob.

Delete the selected Bluetooth device

Press the [VOL] knob.

To download from the cell-phone manually

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “YES”.

By operating the cell-phone, end the hands-free

connection.

“Completed” is displayed.

By operating the cell-phone, send the phone

book data to this unit

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

By operating the cell-phone, download the phone

book data to this unit.

• During downloading:

⁄

• When a registered cell-phone is deleted, its Phone Book,

“Downloading”/ “Download..” is displayed.

• After completion of downloading:

“Completed” is displayed.

log, SMS, and voice tag are also deleted.

By operating the cell-phone, start the hands-

free connection.

To clear the downloading completion message

Press any button.

⁄

• Up to 1000 phone numbers can be registered for each

registered cell-phone.

• Up to 32 digits can be registered for each phone number

along with up to 50* characters representing a name.

(* 50: Number of alphabetic alphabetical characters.

Fewer characters can be input depending on the type of

characters.)

• To cancel downloading of the phone book data, operate

the cell-phone.

English

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

Bluetooth Setup

Select“PB Name Check” (Play)

Press the [VOL] knob.

CompletedSelect“PB Name Delete” (Delete)

Adding a Voice Dialing Command

Add a voice tag to the phone book for voice dialing.

You can register up to 35 voice tags.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

Delete a voice tag

Press the [VOL] knob.

Enter Phone book name edit mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “Voice Tag” > “PB Name

Edit”.

Turn the [VOL] knob to select “YES”, and then

press the [VOL] knob.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

Search for the name to register

• Audio sound is not output during voice tag registration.

Select the name to register with reference to 4 in

<Calling a Number in the Phone Book> (page 21).

If a voice tag has already been registered for a

name, “*” is displayed before the name.

Setting a Voice Command for

Category

Add a voice tag to the phone number category

(type) for voice calling.

Select a mode

Turn the [VOL] knob.

Display

Operation

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

“PB Name Regist.”

“PB Name Check”*

“PB Name Delete”*

Play a voice tag.

Delete a voice tag.

Enter Phone Number type edit mode

Turn the [VOL] knob and press it when the

desired item is displayed.

* Displayed only when a name for which a voice tag has

been registered is selected.

Select “Settings” > “Voice Tag” > “PN Type Edit”.

Select“PB Name Regist.” (Regist)

Select the category (type) you wish to set

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “General”, “Home”, “Office”, “Mobile”, or

“Other”

“Enter Voice 1” is displayed.

When a beep is heard, say a voice tag within 2

seconds.

Select a mode

Turn the [VOL] knob.

Confirm the voice tag (second)

“Enter Voice 2” is displayed.

When a beep is heard, say the same voice tag as

that you said in step 6 within 2 seconds.

“Completed” is displayed.

Display

Operation

“PN Type Regist.”

“PN Type Check”*

“PN Type Delete”*

Play a voice tag.

Delete a voice tag.

End registration

Press the [VOL] knob.

Return to step 2. You can register another voice tag

* Displayed only when a name for which a voice tag has

been registered is selected.

continuously.

steps 5 to 7 in <Adding a Voice Dialing

Command> (page 46).

⁄

• If your voice cannot be recognized, a message is displayed.

Pressing the [VOL] knob allows you to retry voice input.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

• Set the voice tag for all the 5 categories. If the voice tag is

not registered for all the categories, the Phone book may

not be recalled by voice command.

46 DPX-U6120/ DPX-U5120/ DPX-MP3120

Function of DPX-U6120 with KCA-BT200/BT300 (Optional Accessory)

SMS (Short Message Service)

The SMS arrived at the cell-phone is displayed on

the receiver.

A newly arrived message is displayed.

• To prevent car accidents, the driver should not read the

SMS while driving.

VOL

LOG

When a new message arrives

“SMS Received” is displayed.

The display disappears with any operations.

Downloading the SMS

Displaying the SMS

Download the short message (SMS) arrived at the

cell-phone so that it can be read on this unit.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

✍ You can also select from “Settings” in Function

setting mode.

Enter Bluetooth mode

Press the [LOG] button for at least 1 second.

✍ You can also select from “Settings” in Function

setting mode.

Enter SMS Inbox mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “SMS Inbox”.

Enter SMS download mode

Turn the [VOL] knob and press it when the

desired item is displayed.

Select “Settings” > “SMS Download”.

A message list appears.

Select a message

Turn the [VOL] knob.

Each pressing of the [DISP] button switches

between telephone number or name and message

reception date.

Start downloading

Press the [VOL] knob.

“Downloading” is displayed.

When the downloading finishes, “Completed” is

displayed.

Display the text

Press the [VOL] knob.

Turning the [VOL] knob scrolls the message.

Pressing the [VOL] knob again returns to the

message list screen.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

• The cell-phone must be able to transmit the SMS using

Bluetooth. Setting on the cell-phone may be required. If

the cell-phone does not support SMS function, the SMS

download item in Function Control mode is not displayed.

• When the SMS is downloaded from the cell-phone, the

unopened messages in the cell-phone are opened.

• The already-read and unread short messages can be

respectively downloaded up to 75.

Exit SMS Inbox mode

Press the [ ] button.

Exit BT Settings mode

Press the [LOG] button for at least 1 second.

⁄

• The unopened message is displayed at the beginning of the

list. Other messages are displayed in the order of reception.

• The SMS that has arrived when the cell-phone is not linked

with Bluetooth cannot be displayed. Download the SMS.

• The short message cannot be displayed during

downloading the SMS.

English

Basic Operations of remote control

In Tuner source

• Band select: [FM]/[AM]

• Station select: [4]/[¢]

• Recall preset stations: [1] — [6]

• Enter Menu List mode: [5]/[∞]

VOL

SRC

ATT

ENT

5/∞

In USB/Music CD/Audio file source

• Music select: [4]/[¢]

• Folder select: [FM]/[AM]

• Pause/Play: [ENT]

EXIT

AUD

• Enter Menu List mode: [5]

• Enter Music search mode: [∞]

• Movement between folders/files during Search

mode: [5]/[∞]

0 — 9

DIRECT

• Return to previous folder: [

]

In iPod source

• Music select: [4]/[¢]

• Pause/Play: [ENT]

General control

• Enter Menu List mode: [5]

• Volume control: [VOL]

• Source select: [SRC]

• Volume reduce: [ATT]

When the button is pressed again, the volume

returns to the previous level.

• Enter Music search mode: [∞]

• Movement between items during Music search

mode: [5]/[∞]

• Return to previous item: [

]

• Return to previous item: [

• Exit from mode: [EXIT]

• Selection of item: [5]/[∞]

• Determination: [ENT]

]

• Enter Audio Control mode: [AUD]

48 DPX-U6120/ DPX-U5120/ DPX-MP3120

Hands-free phone control

(DPX-U6120 only)

Preparing the remote control unit

Pull the battery sheet out from the remote control

unit to the direction of the arrow.

Making a call

• Enter Bluetooth mode: [

]

• Select a dialing method: [5]/[∞] ➜ [ENT]

• Number dial input:

Input a digit: [0] – [9]

Input “+”: [¢]

Input “#”: [FM]

Input “*”: [AM]

Clear the entered phone number: [4]

• Make a call: [DIRECT]

Changing the battery of the remote control

unit

Keep on slide

Receiving a call

• Answer the call: [

]

• Switch between the private talk mode and the

hands-free talk mode: [ENT]

CR2025

(+side)

Pull out

Call waiting

• Answer Another Incoming Call with the Current

Call Suspended: [

Use a commercially available button battery (CR2025).

Insert the battery with the + and – poles aligned

properly, following the illustration inside the case.

]

• Answer another Incoming Call after Terminating

the Current Call: [SRC]

• Continue the Current Call: [1]

During a call

• End the call: [SRC]

¤ CAUTION

• Do not set the remote control in hot places such

as on the dashboard.

• Lithium battery.

Danger of explosion if the battery is incorrectly

replaced.

Replace only with the same or equivalent type.

• The battery pack or batteries shall not be exposed

to excessive heat such sunshine, fire or the like.

• Keep battery out of reach of children and in

original package until ready to use. Dispose of

used batteries promptly. If swallowed contact

physician immediately.

English

Appendix

About Audio file

About USB device

•

Playable Audio file

• When the USB device is connected to this unit,

it can be charged up provided that this unit is

powered.

AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)

•

Playable disc media

• Install the USB device in the place where it will not

prevent you from driving your vehicle properly.

• You cannot connect a USB device via a USB hub and

Multi Card Reader.

• Save backups of the Audio files used with this unit.

The files can be erased depending on the operating

conditions of the USB device.

We shall have no compensation for any damage

arising out of erasure of the stored data.

• No USB device comes with this unit. You need to

purchase a commercially available USB device.

• When connecting the USB device, usage of the

CA-U1EX (option) is recommended.

• Normal playback is not guaranteed when a cable

other than the USB compatible cable is used.

Connecting a cable whose total length is longer

than 4 m can result in abnormal playback.

CD-R/RW/ROM

Playable disc file format

ISO 9660 Level 1/2, Joliet, Romeo, Long file name.

•

Playable USB device

USB mass storage class

Playable USB device file system

FAT16, FAT32

Even if the Audio files comply with the standards

listed above, the play may be impossible depending

on the types or conditions of media or device.

Playing order of the Audio file

In the example of folder/file tree shown below, the

files are played in the order from ① to ⑩.

•

: Folder

Folder

(1)

udioiofile

Aud ꢀ

¡!

¡"

¡#

¡$

¡%

¡P

An online manual about Audio files is put on the site,

www.kenwood.com/cs/ce/audiofile/. On this online

manual, detailed information and notes which are not

written in this manual are provided. Make sure to read

through the online manual as well.

⁄

• In this manual, the word “USB device” is used for flash

memories and digital audio players which have USB

terminals.

50 DPX-U6120/ DPX-U5120/ DPX-MP3120

iPod/iPhone that can be connected to this

About “KENWOOD Music Editor”

• This unit supports the PC application “KENWOOD

Music Editor Light ver1.1” or later.

unit

Made for

• When you use the Audio file with database

information added by the “KENWOOD Music Editor

Light ver1.1”, you can search a file by title, album or

artist name using the <File Search> (page 13).

• iPod nano (6th generation) • iPod nano (5th generation)

• iPod nano (4th generation) • iPod nano (3rd generation)

• iPod nano (2nd generation) • iPod nano (1st generation)

• iPod with video

• iPod classic

• iPod touch (4th generation) • iPod touch (3rd generation)

• iPod touch (2nd generation) • iPod touch (1st generation)

• In the Instruction manual, the term “Music Editor

media” is used to mean the device that contains

Audio files with database information added with

KENWOOD Music Editor.

• iPhone 4

• iPhone 3GS

• iPhone

• iPhone 3G

• “KENWOOD Music Editor Light ver1.1” is available

from the following web site:

www.kenwood.com/cs/ce/

• For further information on “KENWOOD Music

Editor Light ver1.1”, refer to the site above or the

application help.

• For information on the compatibility of iPod/iPhone

software, visit www.kenwood.com/cs/ce/ipod/.

• Type of control available varies depending

on the type of connected iPod. See

www.kenwood.com/cs/ce/ipod/ for further details.

• The word “iPod” appearing in this manual indicates

the iPod or the iPhone connected with the iPod

connection cable* (optional accessory).

* Not supported model KCA-iP500.

• Refer to the web site for connectable iPod and iPod

connection cable.

www.kenwood.com/cs/ce/ipod/

⁄

• If you start playback after connecting the iPod, the music

that has been played by the iPod is played first.

In this case, “RESUMING” is displayed without displaying a

folder name, etc. Changing the browse item will display a

correct title, etc.

• You cannot operate iPod if “KENWOOD” or “✓” displayed on

iPod.

English

Accessories/ Before installation

system, connect the connectors either to both the front

output terminals or to both the rear output terminals (do

not mix front and rear). For example, if you connect the +

connector of the left speaker to a front output terminal, do

not connect the - connector to a rear output terminal.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

Installation accessories

..........1

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

..........1

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

..........6

Before installation

2 WARNING

• The unit can only be installed in a car with a 12V DC

power supply, negative ground.

• If you connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground),

you may cause a short circuit, that in turn may start

a fire. Always connect those wires to the power

source running through the fuse box.

CAUTION

• Install this unit in the console of your vehicle.

• Do not touch the metal part of this unit during and shortly

after the use of the unit. Metal part such as the heat sink

and enclosure become hot.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• If you experience problems during installation, consult your

Kenwood dealer.Disconnect the battery’s negative terminal

and make all electrical connections before installing the

unit.

• Insulate unconnected wires with vinyl tape or other similar

materials. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• Be sure to ground this unit to the car’s chassis again after

installation.

• If the fuse blows, first make sure the wires are not touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• When only two speakers are being connected to the

52 DPX-U6120/ DPX-U5120/ DPX-MP3120

Connecting Wires to Terminals

Fuse (10A)

Antenna Cord

FM/AM antenna input (JASO)

Front output (DPX-U6120/ DPX-U5120 only)

Rear output/ Sub Woofer output

To Kenwood disc changer/External optional accessory

(DPX-U6120 only)

Wiring harness

(Accessory 1)

To connect these leads, refer to the relevant instruction

⁄

manuals.

White

To front left speaker

White/Black

Gray

Gray/Black

Green

To front right speaker

To rear left speaker

To rear right speaker

Green/Black

Purple

Purple/Black

If no connections are made, do not let the wire come out from the tab.

Blue/White (Power control wire)

Blue (Antenna control wire)

When using the optional power amplifier, connect to its power

control terminal.

P.CONT

Depending on what antenna you are using, connect either to

the control terminal of the motor antenna, or to the power

terminal for the booster amplifier of the film-type or short pole

type antenna.

ANT.

CONT

Brown (Mute control wire)

Connect to the terminal that is grounded when either the

telephone rings or during conversation.

MUTE

To connect the Kenwood navigation system, consult your

⁄

navigation manual.

Orange/ White (Dimmer control wire)

To car light control switch

ILLUMI

Light Blue/ Yellow (Steering

remote control wire)

To use the steering wheel remote control feature, an exclusive

remote adapter (not supplied) that matches your car is required.

REMOTECONT

STEERING WHEEL

REMOTEINPUT

Ignition key

switch

Car fuse

box

ACC

Red (Ignition wire)

Yellow (Battery wire)

Car fuse box

(Main fuse)

Black (Ground wire) · (To car chassis)

–

Battery

English

Installation

Install onto the car bracket using the supplied screws

(M5 × 6 mm, M5 × 7 mm). The holes of the car

bracket to use will differ depending on the car model.

Car Bracket

Accessory3 (M5 × 7 mm)

or Accessory4(M5 × 6 mm)

Accessory2

(Only for NISSAN car)

54 DPX-U6120/ DPX-U5120/ DPX-MP3120

Troubleshooting Guide

Some functions of this unit may be disabled by

some settings made on this unit.

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

• Cannot set up the subwoofer.

• No output from the subwoofer.

• Cannot set up the subwoofer position of Manual

position setting.

General

? The operation check sound (beep sound) does not

• The Dual zone function is enabled.  <Dual Zone

System> (page 35)

• “SubWoofer” of <Audio Control> (page 32)/

“SUBWOOFER SET” of <Audio Control> (page 36) is

not set to ON.

sound.

✔

The preout jack is being used.



The Touch Sensor Tone cannot be output from

the preout jack.

? The illumination flashes when the knob or button

is operated.

• “SubWoofer” >“FC” of <X’Over Setting> (page 38))/

“LPF SUBWOOFER” of <Audio Control> (page 36) is

set to “Through”/ “THROUGH”.

• In the speaker select option, None is selected for

the subwoofer.  <Speaker Setting> (page 37)

✔

This is the key illumination effect.



You set this effect in “ILLUMI Effect” of <Display

Setting> (page 24).

? The key illumination effect brought about in

conjunction with the sound volume is small.

• Cannot set up the equalizer.

• Cannot set up the Bass Boost.

• Cannot set up the Highway sound.

• Cannot set up the Supreme.

• Cannot set up the Position control.

• The Dual zone function is enabled.  <Dual Zone

System> (page 35)

• The DSP function is disabled.  “DSP Set” of <Audio

Control> (page 32)

• In the speaker select option, None is selected for

the rear speakers.  <Speaker Setting> (page 37)

✔

The key illumination effect may be insufficient

depending on the sound volume and sound quality.

Tuner source

? Radio reception is poor.

✔

The car antenna is not extended.



Connect the Antenna control wire to the power

terminal for the booster amplifier of the film-type

or short pole type antenna

Pull the antenna out all the way.

• Cannot select the output destination of the

subsource in the Dual zone.

Disc source

• Cannot adjust the volume of the rear speakers.

The Dual zone function is disabled.  <Dual Zone

System> (page 35)

? The specified disc does not play, but another one

plays instead.

✔

The specified CD is quite dirty.



Clean the CD, referring to the CD cleaning of the

section on <Handling discs> (page 4).

Cannot set up Display.

<Demonstration mode Setting> (page 31) is not

turned off.

The disc is loaded in a different slot from that

specified.



Eject the disc magazine and check the number

for the specified disc.

Cannot switch to USB/iPod source.

The Dual zone function is set to USB/iPod.  <Dual

Zone System> (page 35)

✔

The disc is severely scratched.

Try another disc instead.



Audio file source

The number of songs contained in “SONGS”

category of this unit is different from that

contained in “SONGS” category of iPod.

Podcast files are not counted in this unit as this unit

does not support the playback of podcast files.

? The sound skips when an Audio file is being

played.

✔

The media is scratched or dirty.



Clean the media, referring to the CD cleaning of

the section on <Handling discs> (page 4).

The recording condition is bad.

Record the media again or use another media.



English

Troubleshooting Guide

Hands-free

The messages shown below display your

systems condition.

? The hands-free talk volume is low.

✔

The hands-free talk volume is set at a low level.

TOC Error/TOC ERROR:



The hands-free talk volume can be adjusted

independently. Adjust it during hands-free talk.

“Mic Gain” and “NR Level” <Bluetooth Setting>

(page 42).

• No disc has been loaded in the disc

magazine.

• The CD is quite dirty. The CD is upside-

down. The CD is scratched a lot.

? No sound is heard from the rear speakers.

You are talking in the hand-free talk mode.

Error 05/ERROR 05:

✔

The disc is unreadable.



No sound is heard from the rear speakers in the

hands-free talk mode.

Mecha Error/Mecha ERR/Error 77/ERROR 99/ERROR 77:

The unit is malfunctioning for some reason.

 Press the reset button on the unit. If the

“Mecha Error”/ “Mecha ERR”/ “Error 77”/

“ERROR 99”/ “ERROR 77”code does not

disappear, consult your nearest service

center.

? No beep is heard at reception of an incoming call.

✔

No beep is heard depending on the type of your

cell-phone.



The“Call Beep”of <Bluetooth Setting> (page 42) is

set ON.

? Voice is not recognized.

CD (Blink):

The CD player section is not operating

properly.

✔

The vehicle window is open.



If the surrounding noise is large, voice cannot be

recognized properly. Close the vehicle windows

to reduce noise.

 Reinsert the CD. If the CD cannot be

ejected or the display continues to flash

even when the CD has been properly

reinserted, please switch off the power

and consult your nearest service center.

Small voice.

If voice is too small, it cannot be recognized



properly. Speak into the microphone a little more

loudly and naturally.

The person uttering the voice tag is not the one who

registered the it.

Protect/PROTECT (Blink):

The speaker wire has a short-circuit or

touches the chassis of the vehicle, and then

the protection function is activated.

 Wire or insulate the speaker cable properly

and press the reset button. If the “Protect”

code does not disappear, consult your

nearest service center.



Only the voice of the person who registered the

voice tag can be recognized.

Bluetooth audio source

Unsupported File/NA FILE:

? The Bluetooth audio player cannot be registered

An Audio file is played with a format that this

unit can’t support.

(pairing).

✔

The PIN code is fixed.



When a PIN code is specified in the Instruction

Manual for Bluetooth Audio Player, register it

with reference to <Registering PIN Code> (page

44) to register the Bluetooth audio player. If no PIN

code is specified in the Instruction Manual, try

“0000”.

Copy Protection/COPY PRO:

A copy-protected file is played.

Read Error/READ ERROR:

The file system of the connected USB device

is broken.

 Copy the files and folders for the USB

device again. If the error message is still

displayed, initialize the USB device or use

other USB devices.

? The sound from the Bluetooth audio player is

discontinuous.

✔

The distance between this unit and audio player is

too far.

No Device/NO DEVICE:



Move the audio player nearer to this unit.

The USB device is selected as a source

although no USB device is connected.

 Change the source to any source other

than USB. Connect an USB device, and

change the source to USB again.

✔

Another Bluetooth device is affecting the Bluetooth

communication.



Turn off another Bluetooth device.

Move another Bluetooth device away from this

unit.

✔

Another Bluetooth device or profile is used for

communication.



The downloading of the Phone book or the SMS

disconnects the sound.

56 DPX-U6120/ DPX-U5120/ DPX-MP3120

N/A Device/NA DEVICE:

• An unsupported USB device is connected.

Err No Matching:

The voice tag is wrong. Voice cannot be

recognized because of an unregistered voice

tag, etc.

• Connection to the iPod has failed.

 Remove the USB device and then

reconnect it.

 Check that the connected iPod is an iPod

that is supported. See <About Audio file>

(page 50) for information on supported

iPods.

Too Soft:

Too Loud:

Too Long:

Voice is too small and cannot be recognized.

Voice is too large to be recognized.

The word or utterance is too long to be

recognized.

 Reset iPod/ iPhone.

No Music Data/Error 15/No Music/NO MUSIC/EROOR 15:

• The connected USB device contains no

playable Audio file.

No Phonebook: Data is not contained in the phone book.

No Message: No short message in In Box.

• Media was played that does not have data

recorded that the unit can play.

No Record:

The voice tag is not registered in the phone

book.

USB Error/USB ERROR:

Memory Full: The number of voice tags reaches the

maximum number to be registered in the

phone book.

Some trouble may have occurred to the

connected USB device.

 Remove the USB device, then cycle the

power switch to ON. If the same display is

repeated, use another USB device.

No Voice:

No call.

iPod Error/iPod ERROR:

Connection to the iPod has failed.

 Remove the USB device and then

reconnect it.

 Reset iPod/ iPhone.

No Number:

No Data:

• The calling party does not notify a caller ID.

• There is no phone number data.

• There is no outgoing call list.

• There is no incoming call list.

• There is no missed call list.

• There is no phone book list.

No Entry:

The cell-phone has not been registered

(pairing).

HF Disconnect/HF D-CON:

The unit cannot communicate with the cell-

phone.

HF Error 07:

The memory cannot be accessed.

 Turn off the power and on again. If this

message still appears, press the reset

button on the control unit.

HF Error 68:

The unit cannot communicate with the cell-

phone.

 Turn off the power and on again. If this

message still appears, press the reset

button on the control unit.

Unknown:

The Bluetooth device cannot be detected.

Device Full:

5 Bluetooth device have already been

registered. No more Bluetooth device cannot

be registered.

PIN Code NG: The PIN code is wrong.

Connect NG: The unit cannot be connected to the device.

Pairing Failed: Pairing error.

English

Specifications

FM tuner section

USB Interface (DPX-U6120/ DPX-U5120)

Frequency range

200 kHz step : 87.9 MHz – 107.9 MHz

USB Standard

: USB1.1/ 2.0 (Full speed)

50 kHz step : 87.5 MHz – 108.0 MHz

Usable sensitivity (S/N = 26dB)

DPX-U6120: 8.1 dBf (0.7 μV/75 Ω)

DPX-U5120/ DPX-MP3120: 11.2 dBf (1 μV/75 Ω)

Quieting Sensitivity (S/N = 50dB)

DPX-U6120: 15.3 dBf (1.6 μV/75 Ω)

DPX-U5120/ DPX-MP3120: 19.2 dBf (2.5 μV/75 Ω)

Frequency response ( 3 dB)

: 30 Hz – 15 kHz

Signal to Noise ratio (MONO)

DPX-U6120: 65 dB

DPX-U5120/ DPX-MP3120: 63 dB

Maximum Supply current

: 500 mA

File System

: FAT16/ 32

MP3 decode

: Compliant with MPEG-1/2 Audio Layer-3

WMA decode

: Compliant with Windows Media Audio

AAC decode

: AAC-LC ”.m4a” files

Audio section

Stereo separation (1 kHz)

: 40 dB

Maximum output power

: 50 W x 4

Full Bandwidth Power (at less than 1% THD)

: 22 W x 4

AM tuner section

Frequency range

10 kHz step : 530 kHz – 1700 kHz

9 kHz step : 531 kHz – 1611 kHz

Usable sensitivity (S/N = 20dB)

DPX-U6120: 28 dBµ (25 µV)

Speaker Impedance

: 4 – 8 Ω

Tone action

DPX-U6120

BAND1 (60 Hz): 9 dB

BAND2 (250 Hz): 9 dB

BAND3 (1 kHz): 9 dB

BAND4 (4 kHz): 9 dB

BAND5 (16 kHz): 9 dB

DPX-U5120/ DPX-MP3120

Bass : 100 Hz 8 dB

Middle : 1 kHz 8 dB

Treble : 12.5 kHz 8 dB

Preout level / Load (CD)

DPX-U6120: 2500 mV/10 kΩ

DPX-U5120/ DPX-MP3120: 31 dBµ (36 µV)

CD player section

Laser diode

: GaAlAs

Digital filter (D/A)

: 8 Times Over Sampling

D/A Converter

: 24 Bit

Spindle speed

: 500 – 200 rpm (CLV)

Wow & Flutter

: Below Measurable Limit

DPX-U5120/ DPX-MP3120: 2000 mV/10 kΩ

Preout impedance

: ≤ 600 Ω

Frequency response ( 1 dB)

: 10 Hz – 20 kHz

Auxiliary input

Total harmonic distortion (1 kHz)

: 0.008 %

Signal to Noise ratio (1 kHz)

: 105 dB

Dynamic range

: 93 dB

MP3 decode

: Compliant with MPEG-1/2 Audio Layer-3

WMA decode

: Compliant with Windows Media Audio

AAC decode

: AAC-LC “.m4a” files

Frequency response ( 1 dB)

: 20 Hz – 20 kHz

Input Maximum Voltage

: 1200 mV

Input Impedance

: 10 kΩ

General

Operating voltage (11 – 16V allowable)

: 14.4 V

Maximum Current consumption

: 10 A

Installation Size (W x H x D)

: 182 x 111 x 158 mm

Weight

: 1.5 kg

Specifications subject to change without notice.

58 DPX-U6120/ DPX-U5120/ DPX-MP3120

The marking of products using lasers

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says that the component

uses laser beams that have been classified as Class 1. It means that the

unit is utilizing laser beams that are of a weaker class. There is no danger

of hazardous radiation outside the unit.

This symbol mark indicates that Kenwood

manufactured this product so as to

decrease harmful inﬂuence on the

environment.

• The Bluetooth word mark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks

by Kenwood Corporation is under license. Other

trademarks and trade names are those of their

respective owners.

• The “AAC” logo is a trademark of Dolby Laboratories.

• iTunes is a trademark of Apple Inc.

• “Made for iPod” and “Made for iPhone” mean that an

electronic accessory has been designed to connect

specifically to iPod or iPhone, respectively, and has

been certified by the developer to meet Apple

performance standards. Apple is not responsible for

the operation of this device or its compliance with

safety and regulatory standards. Please note that the

use of this accessory with iPod or iPhone may affect

wireless performance.

• iPhone, iPod, iPod classic, iPod nano, and iPod touch

are trademarks of Apple Inc., registered in the U.S. and

other countries.

• “Adobe Reader” is a trademark of Adobe Systems

Incorporated.

English

Indesit Washer Dryer WIDXL 106 User Manual
ION DJ Equipment DISCOVER DJ User Manual
Jacuzzi Hot Tub Y200 User Manual
Jet Tools Sander Drum Sander User Manual
JL Audio Car Speaker SB F TRKEXT 8W1 User Manual
JVC Camcorder TK WD310U User Manual
JVC MP3 Player UX V330R User Manual
Klipsch Speaker AW 800 SW User Manual
Kompernass Food Warmer KH 1610 User Manual
Kramer Electronics VCR PT 1Hs User Manual