MODEL 840458
19.2V BATTERY-OPERATED
IMPACT WRENCH
INSTRUCTION MANUAL
BATTERIES AND
CHARGERS
SOLD SEPARATELY
Conforms to UL Std. 60745-1,
60745-2-2
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
3100224
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.
YOUR FEEDBACK IS VITAL TO US.
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
1-800-590-3723
LONG BEACH, CA 90810-1462 USA
840458 –19.2V Cordless Impact Wrench_Rev 6/21/07
Printed in China
WORK AREA
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
CAUTION indicates
situation which, if not avoided, may result in
minor or moderate injury.
a
potentially hazardous
Do not operate power tools in explosive atmospheres, such as in the pres-
ence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
ELECTRICAL SAFETY
IMPORTANT SAFEGUARDS
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery. A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Use battery operated tool only with specifically designated battery pack. Use of
any other batteries may create risk of fire.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
3
4
PERSONAL SAFETY
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery termi-
nals together may cause sparks, burns or a fire.
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack. Carrying power tools with your finger on the
switch or inserting battery pack into a tool with the power switch “ON” invites
accidents.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Remove adjusting keys or wrenches before turning the tool “ON”. A wrench
or a key that is left attached to a rotating part of the tool may result in person-
al injury.
SERVICE
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enable better control of the tool in unexpected situations.
Tool service must be performed only by qualified repair personnel. Service
or maintenance by unqualified personnel may result in a risk of injury.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safe-
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.
When servicing a tool, use only identical replacement parts. Follow instruc-
tions in the Maintenance section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a risk of shock or injury.
TOOL USE AND CARE
SPECIFIC SAFETY RULES AND / OR SYMBOLS
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Hold tool by insulated gripping surfaces when perform-
ing an operation where the cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
Do not force tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that
cannot be controlled with the switch is dangerous and must be repaired.
SAFETY RULES FOR IMPACT WRENCHES
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-
tion before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Always wear safety goggles or eye protection when using this tool. Use a
dust mask or respirator for applications which generate dust.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Do not grasp the tool or place your hands too close to the spinning chuck or
drill bit. Your hand may be lacerated or may cause injury.
5
6
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
Secure the material being worked on. Never hold it in your hand or across
your legs. Unstable support can cause loss of control and injury.
Position yourself to avoid being caught between the tool or side handle and
walls or posts. Should the socket or bit become bound in the work, the reac-
tion torque of the tool could crush your hand or leg.
SYMBOL
NAME
EXPLANATION
V
Volts
Voltage (Potential)
Check to see that keys and adjusting wrenches are removed from the
Cordless Impact Wrench before switching the tool “ON”. Keys or wrenches
can fly away at high velocity striking you or a bystander.
A
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
Current
Hz
W
Kg
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
When using the Cordless Impact Wrench, always maintain a firm grip on the
tool with both hands.
Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring. Contact with a "live" wire
will also make exposed metal parts of the tool "live" and shock the operator.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Keep the handle of the Cordless Impact Wrench dry, clean, and free from oil
and grease.
min
s
Do not run the Cordless Impact Wrench while carrying it at your side. A spin-
ning socket or bit could become entangled with clothing and injury may result.
Disconnect the plug or remove the battery pack from tool and place the switch
in the locked or “OFF” position before making any assembly adjustments,
changing accessories, performing any inspection, maintenance or cleaning
procedures. Such preventive safety measures reduce the risk of starting the
tool accidentally.
No load speed
Revolutions per Minute
.../min
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
Do not use the Cordless Impact Wrench if it has been damaged, left outdoors
in the rain, snow, wet or damp environments, or immersed in liquid.
Maintain labels and nameplates on the Cordless Impact Wrench. These carry
important information. If unreadable or missing, contact Alltrade for a replace-
ment.
7
8
FUNCTIONAL DESCRIPTION
Use only Kawasaki™ 19.2V Battery Pack #691034 or
#691240 with the One Hour Charger #690507 or Charger #690072/ Adapter
#690074.
3
CONTROLS AND COMPONENTS:
1. Variable Speed Trigger Switch
4
2. Forward/Reverse and
Trigger Lock Lever
6
3. Gear Enclosure
4. Anvil
2
1
The battery is not fully charged.
5
5. Comfort Rubber Grip
ACCESSORIES:
6. 1/2" Drive Impact Socket (4)
Charger #690072/ Adapter #690074 - Before first use, the battery pack
requires 8-10 hours charge time to be fully charged. Subsequent recharging
needs 3-5 hours for the battery to be fully charged.
7. 3/8" Adapter
One Hour Charger #690507 - Before first use, the battery pack requires 3-5
hours charge time to be fully charged. Subsequent recharging needs 1 hour for
the battery to be fully charged.
7
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
BATTERY
Never over-discharge a battery by using the tool even after tool performance
has decreased. Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Before using battery pack, please read carefully all instruc-
tions and cautionary markings on battery pack, battery
charger and product using battery.
Charge battery pack at ambient temperatures between 50° F – 104° F.
®
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
Do not incinerate the battery pack even if it is severely dam-
aged or is completely worn out. The battery pack can explode.
The battery pack should always be recharged when the Cordless Impact Wrench
begins to run slowly.
Do not carry battery packs in aprons, pockets, or tool
boxes, product kit boxes, drawers, etc. with loose metal objects. Battery
pack terminals could be short circuited causing damage to the battery pack,
severe burns or fire.
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause sparks, burns, or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency. Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
9
10
REMOVING / ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either side of
the Impact Wrench to release the battery
pack.
CHARGING BATTERY PACK USING CHARGER #690072 / ADAPTER #690074
CHARGE BATTERY PACK:
1. Make sure the trigger on the
Cordless Impact Wrench is
in the “OFF” position and
remove the battery pack
from the Impact Wrench.
BATTERY PACK
120V AC
ADAPTER
2. Pull battery pack free of Impact Wrench.
ATTACH BATTERY PACK:
LED LIGHT
2. Insert the battery pack into
the charger. Be sure that the
battery pack is fully seated
in the charger. Do not force.
1. Align the raised portion of the battery pack
with the groove in the battery compartment
of the Impact Wrench.
RELEASE
BUTTON
2. Press the battery pack into place. Make sure
the latches are securely fastened. Do not use
the Impact Wrench if the battery pack is not
seated properly.
3. Plug the charger into the
nearest 120 volt, electrical
outlet. The indicator light
will come “ON” .
BATTERY
CHARGER
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Impact Wrench continuously, the batteries in your bat-
tery pack will become hot. You should let a hot battery pack cool down for approx-
imately 30 minutes before attempting to recharge. When the battery pack becomes
discharged and is hot, the red light on the charger will flash. When the battery pack
cools down, the red light will glow continuously.
CHARGER #690072 / ADAPTER #690074
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
This will occur when continuous use of your Cordless
Impact Wrench causes the battery pack to become hot. It does not occur
under normal circumstances.
The charger will not automatically turn “OFF” when the
battery pack is fully charged. The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet.
ONE HOUR CHARGER #690507
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
The battery pack and charger heat during charging. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
Do not disassemble charger.
When the battery pack requires recharging, a 3-5 hour charge allows the tool to
operate at full power. A charging indicator light on the charger will illuminate to
show that charging is taking place.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
11
12
The battery pack and charger heat during charging. Place the charger on a flat,
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
INSTALLING / REMOVING SOCKET ON THE ANVIL
When removing the socket or bit from the tool, avoid
contact with skin and use proper protective gloves when grasping the socket,
bit or accessory. Accessories may be hot after prolonged use.
When the battery pack requires recharging, a 1 hour charge allows the tool to
operate at full power. A charging indicator light on the charger will illuminate to
show that charging is taking place.
CHARGING BATTERY PACK USING ONE HOUR CHARGER #690507
BATTERY PACK
CHARGE BATTERY PACK:
1. Plug the charger into the nearest
120 volt electrical outlet. The
step of the battery has positive
and negative terminal markings
on it. Align the markings with
the identical markings on the top
of the charger base. Insert the
battery pack into base. Pack will
not insert properly if reversed.
When installing a socket, align the
holes in the side of the socket with the
dent pin. Press the socket on until the
dent pin engages in the hole. To remove a
socket, depress the dent pin through the
hole using a small pointed object and pull
the socket off.
2. Make sure the trigger on the
Impact Wrench is in the “OFF”
position and remove the battery
pack from the Cordless Impact
CHARGER
Wrench.
OPERATING THE IMPACT WRENCH
BATTERY
Never tape the trigger switch down to provide continuous
high speed. The tool may fail under such conditions causing fire or
personal injury.
3. If, when first inserting the battery pack, the red “ON” button does not light up,
press the “SET” button on the charger. When the battery is charging, the red
light is “ON” .
VARIABLE SPEED TRIGGER SWITCH
4. After approximately one hour of charging, the red indicator light should go
“OFF” and the green light should come “ON” . The green light indicates that the
battery is fully charged.
THIS TOOL IS CONTROLLED
BY A TRIGGER SWITCH:
• The speed of the Cordless Impact
Wrench depends on the amount of
pressure you put on the trigger.
5. When fully charged, reattach battery pack onto Cordless Impact Wrench, mak-
ing certain latches fasten securely. Cordless Impact Wrench will not operate
properly if the battery pack is not seated properly.
• The more pressure you apply, the
TRIGGER
SWITCH
faster the Cordless Impact
Wrench will go.
ASSEMBLY
• Release the pressure and the
Cordless Impact Wrench will slow
down.
Be aware that this tool is always in an operating condi-
tion because it does not have to be plugged into an electrical outlet. Always
turn the switch “OFF” and remove the battery pack before changing bits.
13
14
FORWARD / REVERSE AND TRIGGER LOCK LEVER
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the “LOCKED/OFF” position.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
Always check the direction of the Cordless Impact Wrench's rotation before use.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may
experience a loss of power, excessive voltage drop or overheating. The smaller the
gauge number, the heavier the cord (see table below).
TO SELECT THE DIRECTIONS
OF ROTATION:
• To select forward Cordless
Impact Wrench rotation, press
the trigger lock from left to
right flat against the Cordless
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
Impact Wrench body.
AMPERE
3-6
6-8
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
Reverse Lock Forward
TRIGGER
LOCK
18
16
14
14
-
• To select reverse, press the
trigger lock lever in the
opposite direction.
8-10
10-12
12-16
16-20
• The center position locks the
tool.
14
12
12
12
12
12
-
MAINTENANCE AND CLEANING
SPECIFICATIONS
SPECIFICATIONS
19.2V
Always remove the battery pack before attempting
cleaning or maintenance.
Voltage
Speed
0-2000 RPM (no load)
0-4000 BPM
180 ft.lbs.
Impacts Per Minute
Maximum Torque
Battery Type
This Cordless Impact Wrench is lubricated before it
leaves the factory. This lubrication should last for the life of the tool. No
further lubrication is required.
Ni-Cad
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
PROTECTING THE ENVIRONMENT
BATTERIES
Always clean the battery pack using only a dry cloth. Do not use liquids.
Always unplug the charger before cleaning it.
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
Never open the Cordless Impact Wrench case, battery pack or charger. Do not
attempt to repair the Cordless Impact Wrench, battery pack or charger yourself.
Opening any of these parts will void your warranty.
15
16
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service 1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Reciprocating Saws
Routers
Rotary Tools
Jigsaws
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
Circular Saws
Angle Grinders
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of
projects and repairs in and around the home. Use of the tool for COMMERCIAL
PURPOSES OR ON A JOBSITE is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
Warranty Performance
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
17
18
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
19
20
|