MODEL
840443
19.2V BATTERY-OPERATED JIGSAW
INSTRUCTION MANUAL
BATTERIES AND CHARGERS
SOLD SEPARATELY
Conforms to Std. UL745-3,
UL745-4-11
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
87-1904-60957
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
PARA EL SERVICIO
PARA EL CONSUMIDOR
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS
CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
1-800-590-3723
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
Printed in China
Imprimé dans la Chine
Impreso en China
840443_19.2V Black Cordless Jigsaw _Rev 7/27/07
WORK AREA
DANGER
indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
WARNING
indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
CAUTION
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
ELECTRICAL SAFETY
NOTE
provides additional information that is useful
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
immediately.
Damaged cords may create a fire.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery.
IMPORTANT SAFEGUARDS
A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Use battery operated tool only with specifically designated battery pack.
Use of
any other batteries may create risk of fire.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING:
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
Wash hands after handling.
defects or other reproductive harm.
4
PERSONAL SAFETY
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
make a connection from one terminal to another.
Shorting the battery termi-
nals together may cause sparks, burns or a fire.
alcohol or medication.
A moment of inattention while operating power tools
Maintain tools with care. Keep cutting tools sharp and clean
. Properly maintained
tools with sharp cutting edge are less likely to bind and are easier to control.
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
Keep your hair, clothing, and gloves away from moving parts.
Loose clothes,
jewelry or long hair can be caught in moving parts.
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack.
Carrying power tools with your finger on the
Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
“ON”
switch or inserting battery pack into a tool with the power switch
accidents.
invites
Remove adjusting keys or wrenches before turning the tool “ON”.
or a key that is left attached to a rotating part of the tool may result in person-
al injury.
A wrench
SERVICE
Do not overreach. Keep proper footing and balance at all times.
Proper foot-
ing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Tool service must be performed only by qualified repair personnel.
or maintenance by unqualified personnel may result in a risk of injury.
Service
Dust mask, non-skid safe-
ty shoes, hard hat, or hearing protection must be used for appropriate conditions..
When servicing a tool, use only identical replacement parts. Follow instruc-
tions in the Maintenance section of this manual.
Use of unauthorized parts or
failure to follow Maintenance Instructions may create a risk of shock or injury..
TOOL USE AND CARE
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Use clamps or other practical ways to secure and support the workpiece to a
stable platform.
may lead to loss of control.
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
Holding the work by hand or against your body is unstable and
Do not force tool. Use the correct tool for your application.
will do the job better and safer at the rate for which it is designed.
The correct tool
Do not use the tool if the power switch does not turn it “ON” or “OFF”.
cannot be controlled with the switch is dangerous and must be repaired.
A tool that
SAFETY RULES FOR CORDLESS JIGSAWS
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-
tion before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Always wear safety goggles or eye protection when using this tool. Use a dust
mask or respirator for applications which generate dust.
Store idle tools out of reach of children and other untrained persons.
Tools
Secure the material being worked on. Never hold it in your hand or across
are dangerous in the hands of untrained users.
your legs.
Unstable support can cause loss of control and injury.
5
6
SYMBOLS
IMPORTANT:
Some of the following symbols may be used on your tool. Please
When using the Cordless Jigsaw, always maintain a firm grip on the tool with
both hands.
tool or place your hands too close to the blade. Keep your hands well away from
the sanding disk. Never reach underneath the tool while the sanding disk is in
motion. Do not use your legs or feet to stabilize the work piece.
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
Never put your hands or feet in the sanding area. Do not grasp the
SYMBOL
NAME
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
V
A
Hz
W
Kg
Volts
Amperes
Hertz
Position yourself to avoid being caught between the tool or side handle and
walls or posts.
Should the socket or bit become bound in the work, the reac-
tion torque of the tool could crush your hand or leg.
Watt
Always hold the tool by its insulated gripping surfaces when cutting in areas
Kilograms
Alternating Current
Direct Current
Weight
Type of Current
Type of Current
that may contain hidden live wiring.
If the blade makes contact with a live
wire, the metal parts of this tool may conduct enough electricity to seriously
shock the user. Contact with a “live” wire will make exposed metal parts of the tool
“live” and shock the operator. Do not cut or break into existing walls or other blind
areas where electrical wiring may exist. If this situation is unavoidable, disconnect
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
all
fuses
or circuit breakers feeding this worksite.
min
s
Do not run the Cordless Jigsaw while carrying it at your side.
A moving blade
Seconds
could become entangled with clothing and injury may result.
Diameter
Size of Drill Bits,
Disconnect the battery pack from tool and place the switch in the locked or
“OFF” position before making any assembly adjustments, changing acces-
Grinding Wheels, etc.
No load speed
No-load Rotational Speed
sories, performing any inspection, maintenance or cleaning procedures.
Such
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
preventive safety measures reduce the risk of starting the tool accidentally.
Do not use the Cordless Jigsaw if it has been damaged, left outdoors in the
rain, snow, wet or damp environments, or immersed in liquid.
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
Do not use dull or damaged blades.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
When restarting a saw in the workpiece, check that teeth are not engaged in
the material.
Keep the handle of the Cordless Jigsaw dry, clean, and free from oil and
grease.
Be extra careful when cutting in high or hard-to-reach locations.
Be on the
lookout for hidden wires and falling debris.
Maintain labels and nameplates on the Cordless Jigsaw.
These carry impor-
tant information. If unreadable or missing, contact Alltrade for a replacement.
7
8
FUNCTIONAL DESCRIPTION
9
Use only Kawasaki™ 19.2V Battery Pack #691034 or
#691240 with the One Hour Charger #690507 or Charger #690072/ Adapter
#690074.
11
8
CONTROLS AND COMPONENTS:
10
1. ON/OFF Trigger Switch
2. Lock-on Button
3. Dust Shroud
4. Screws
5. Blade Support Roller
6. Shoe Plate
2
The battery is not fully charged.
1
Charger #690072/ Adapter #690074 -
Before first use, the battery pack
7. Allen Wrench
8. Comfort Rubber Grip
9. Snap Hook
requires 8-10 hours charge time to be fully charged. Subsequent recharging
needs 3-5 hours for the battery to be fully charged.
7
3
One Hour Charger #690507 -
Before first use, the battery pack requires 3-5
4
ACCESSORIES:
10. Metal Cutting Blade
11. Wood Cutting Blade
hours charge time to be fully charged. Subsequent recharging needs 1 hour for
the battery to be fully charged.
5
6
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
BATTERY
Never over-discharge a battery by using the tool even after tool performance
has decreased.
Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Before using battery pack, please read carefully all instruc-
tions and cautionary markings on battery pack, battery
charger and product using battery.
Charge battery pack at ambient temperatures between 50° F – 104° F.
®
Do not incinerate the battery pack even if it is severely
Store tool and battery pack in locations where temperatures will not exceed
damaged or is completely worn out.
The battery pack can
120°F.
This is important to prevent serious damage to the battery cells.
explode.
The battery pack should always be recharged when the Cordless Jigsaw begins
to run slowly.
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects.
be short circuited causing damage to the battery pack, severe burns or fire.
Battery pack terminals could
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another.
together may cause sparks, burns, or fire.
Shorting the battery terminals
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.
Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
1-800-822-8837
call
.
9
10
REMOVING / ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
CHARGING BATTERY PACK USING CHARGER #690072 / ADAPTER #690074
BATTERY PACK
CHARGE BATTERY PACK:
1. Press both release
buttons on either
side of the Cordless
Jigsaw to release the
battery pack.
1. Make sure the trigger on
the Cordless Jigsaw is in
120V AC
ADAPTER
“OFF”
the
position and
remove the battery pack
from the Cordless Jigsaw.
2. Pull battery pack free of
Cordless Jigsaw.
2. Insert the battery pack into
the charger. Be sure that
the battery pack is fully
seated in the charger. Do
not force.
RELEASE
BUTTON
LED LIGHT
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack with the groove in the battery com-
partment of the Cordless Jigsaw.
3. Plug the charger into the
nearest 120 volt, electrical
BATTERY
CHARGER
2. Press the battery pack into place. Make sure the latches are securely fastened.
Do not use the Cordless Jigsaw if the battery pack is not seated properly.
“ON”
outlet. The indicator light will come
.
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your Cordless Jigsaw continuously, the batteries in your battery pack
will become hot. You should let a hot battery pack cool down for approximately 30
minutes before attempting to recharge. When the battery pack becomes discharged
and is hot, the red light on the charger will flash. When the battery pack cools down,
the red light will glow continuously.
CHARGER #690072 / ADAPTER #690074
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
This will occur when continuous use of your Cordless
Jigsaw causes the battery pack to become hot.
It does not occur under nor-
The charger will not automatically turn “OFF” when the
mal circumstances.
battery pack is fully charged.
The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet.
ONE HOUR CHARGER #690507
Use only the charger which accompanied your product or direct replacement as
listed in this manual.
Do not substitute any other charger. Use only Alltrade
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
Use only the charger which accompanied your product or direct replacement as
listed in this manual.
Do not substitute any other charger. Use only Alltrade
The battery pack and charger heat during charging.
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
Place the charger on a flat,
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
When the battery pack requires recharging, a 3-5 hour charge allows the tool to
operate at full power.
A charging indicator light on the charger will illuminate to
show that charging is taking place.
11
12
The battery pack and charger heat during charging.
Place the charger on a flat,
ATTACHING THE BLADE
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 1 hour charge allows the tool to
Always remove battery pack before installing or removing blade.
operate at full power.
A charging indicator light on the charger will illuminate to
When removing the blade from the tool, avoid contact with skin and use
show that charging is taking place.
proper protective gloves when grasping the blade or accessory.
Accessories
may be hot after prolonged use.
CHARGING BATTERY PACK USING ONE HOUR CHARGER #690507
1. Loosen the two screws
CHARGE BATTERY PACK:
1. Plug the charger into the
nearest 120 volt electrical
outlet. The step of the bat-
tery has positive and nega-
tive terminal markings on it.
Align the markings with the
identical markings on the
top of the charger base.
Insert the battery pack into
base. Pack will not insert
properly if reversed.
BATTERY PACK
on the blade holder
LOOSEN
TIGHTEN
by turning them count-
er-clockwise. Push the
blade shank into the saw
blade holder as far
as it will go. Make sure
that the blade’s teeth
are facing forward.
2. Tighten the screws slowly, first one
side, then the other, until the blade
reaches the desired position.
Tighten the screws completely to
hold the blade in place.
BATTERY
CHARGER
2. Make sure the trigger on the
Cordless Jigsaw is in the
“OFF”
position and remove the battery pack from the Cordless Jigsaw.
“ON”
3. If, when first inserting the battery pack, the red
button does not light up,
OPERATING THE JIGSAW
press the “SET” button on the charger. When the battery is charging, the red
“ON”
light is
4. After approximately one hour of charging, the red indicator light should go
“OFF” “ON”
.
Never tape the trigger switch down to provide continuous
The tool may fail under such conditions causing fire or personal
and the green light should come
battery is fully charged.
. The green light indicates that the
high speed.
injury.
5. When fully charged, reattach battery pack onto Cordless Jigsaw, making certain
latches fasten securely. Cordless Jigsaw will not operate properly if the battery
pack is not seated properly.
ASSEMBLY
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet.
Always turn
“OFF”
the switch
and remove the battery pack before changing blades.
13
14
OPERATING THE ON/OFF SWITCH
PLUNGE CUTTING
• Depress the lock-on
button to one side.
LOCK-ON
BUTTON
Never feed the blade into the work piece until the blade
is at full speed. If the blade is not at full speed, the saw may kick back
causing serious personal injury.
• Press the trigger in to
“ON”
turn the Jigsaw
• Mark out the line to be cut so it is easily visible.
• Start inside the area to be cut out.
and release the trigger
to stop the Jigsaw.
TRIGGER
SWITCH
• Depress the lock-on button and press the trigger to start the saw.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
METAL CUTTING
GENERAL CUTTING
Never use gasoline or any flammable liquid as a
lubricant. Sparking from the motor may cause it to ignite into flames.
• When cutting metals other then copper, brass or aluminum, always use a lubricant,
such as cutting oil, to keep the blade cool. This will prolong the life of the blade as
well as speeding up the cutting process.
Always hold the saw in front of you and away from your body. Keep your
hands and feet well away from the work piece.
Never feed the blade into the work piece until the blade is at full speed.
If the blade is not at full speed, the saw may kick back causing serious
personal injury.
• Make sure the work piece is held securely in place. Hold smaller pieces, such as
pipe or conduit, in a vise or attach to the workbench with clamps.
• To eliminate vibration, always cut close to the clamping point.
• When cutting thin sheets of metal, place a piece of plywood on either side to control
vibration and prevent tearing.
Do not force the saw. Excessive force may result in a
Use only enough pressure to keep the saw moving through the
broken blade.
work piece.
MAINTENANCE AND CLEANING
• Put on eye protection.
Always remove the battery pack before attempting
cleaning or maintenance.
• Clear the saw of any foreign material.
• Make sure the work piece is held securely in place. Hold smaller pieces in a vise
or attach to the workbench with clamps.
• Mark out the line to be cut so it is easily visible.
• Pull the trigger to start the saw.
This Cordless Jigsaw is lubricated before it leaves the
This lubrication should last for the life of the tool. No
factory.
further lubrication is required.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
15
16
Always clean the battery pack using only a dry cloth. Do not use liquids.
Always unplug the charger before cleaning it.
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life,
recycle batteries with due care for our environment.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
Never open the Cordless Jigsaw case, battery pack or charger.
repair the Cordless Jigsaw, battery pack or charger yourself. Opening any of these
parts will void your warranty.
Do not attempt to
1-800-822-8837
. Collected batteries will be recycled or disposed of properly.
or call
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
ACCESSORIES
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.
If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
Jigsaws
Circular Saws
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
Angle Grinders
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
Reciprocating Saws
Routers
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
14
12
12
12
12
12
-
SPECIFICATIONS
SPECIFICATIONS
Voltage
19.2V
Length of Stroke
Strokes per minute
Max. Cutting Thickness
Charger Input
15mm
0-2000/min.
20mm
120V
60Hz
Battery Type
Ni-Cad
17
18
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:
Kawasaki™ portable power tool is offered as a home use tool and carries a
This
HOME
USE WARRANTY
.
This tool is made for home use in the execution of
COMMERCIAL
projects and repairs in and around the home. Use of the tool for
PURPOSES OR ON A JOBSITE
is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
THERE ARE NO WARRANTIES
for which Alltrade makes no warranties whatsoever.
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service 1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
19
20
Warranty Disclaimers
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
21
22
|