JLWM 1404
1400 spin washing machine
Instruction manual
• Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items
to slip down between the tub and the
inner drum.
• If the appliance is installed in a location
subject to frost, please read the “dangers
of freezing” chapter.
• Any plumbing work required to install this
appliance should be carried out by a
• Do not use your washing machine to
wash articles with whalebones, material
without hems or torn material.
qualified plumber or competent person.
• Any electrical work required to install this
appliance should be carried out by a
• Always unplug the appliance and turn off
the water supply after use and during
cleaning and maintenance.
• Under no circumstances should you
attempt to repair the machine yourself.
Repairs carried out by inexperienced
people may cause injury or serious
malfunctioning. Contact your local Service
Centre. Always insist on genuine spare
parts.
qualified electrician or competent person.
Use
• This appliance is designed for domestic
use. It must not be used for purposes
other than those for which it was
designed.
• Only wash and dry fabrics which are
designed to be machine washed or dried.
Follow the instructions on each garment
label
• Do not overload the appliance. See the
Washing Programme Table.
• Before washing, ensure that all pockets
are empty and buttons and zips are
fastened. Avoid washing frayed or torn
articles and treat stains such as paint, ink,
rust, and grass before washing.
Underwired bras must NOT be machine
washed.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if
this is not adhered to. See relevant
section in the user manual.
• After having installed the appliance, check
that it is not standing on the inlet and
drain hose and the worktop is not
pressing the electrical supply cable against
the wall.
• Garments which have been in contact
with volatile petroleum products should
not be machine washed. If volatile
cleaning fluids are used, care should be
taken to ensure that the fluid is removed
from the garment before placing in the
machine.
• If the machine is situated on a carpeted
floor, please adjust the feet in order to
allow air to circulate freely under the
appliance.
• Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
• As some duvets and eiderdowns should
be washed/dried in large commercial
machines because of their bulk, please
check with the manufacturer of the item
before washing in a domestic machine.
3
• The users should always check that they
have not left their gas lighters (disposable
or otherwise) in their clothing.
• Never tumble dry items that have had
contact with chemicals such as dry
cleaning fluid. These are of a volatile
nature and could cause an explosion.
Only tumble dry items which have been
washed in water or require airing.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to
children - danger of suffocation! Keep
them out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not
climb into the drum. To prevent children
and pets becoming trapped inside the
drum the machine incorporates a special
feature. To activate this device, rotate the
button (without pressing it) inside the
door clockwise until the groove is
• Plastic detergent dispensers should not
remain in the drum during the drying
cycle, as the plastic used is not designed
to withstand the heat. If you wish to
wash-through-to-dry you should use the
conventional detergent dispenser drawer.
horizontal. If necessary use a coin.
• Never pull the power supply cable to
remove the plug from the socket; always
take hold of the plug itself.
• Never use your new appliance if the
power supply cable, the control panel, the
working surface or the base are damaged
so that the inside of the appliance is
accessible.
Child safety
• This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for
their safety.
To disable this device and restore the
possibility of closing the door, rotate the
button counterclockwise until the groove
is vertical.
4
Contents
Operating instructions
Installation instructions
Safety information
General safety
Installation
Use
Child safety
2
2
3
3
4
Installation
28
28
29
29
30
30
32
32
33
Unpacking
Positioning and levelling
Plumbing in
Water inlet
Water drainage
Product description
Detergent dispenser drawer
7
8
Special conditions
In the interest of the environment
Electrical connection
Control panel
Programme Dial (2)
Spin (3)
8
9
9
What to do if…
35
Repairs - After Sales Service 38
Prewash (4)
Intensive (5)
9
10
10
10
10
10
10
Environment concerns
Packaging materials
39
39
39
Extra Rinse (6)
Quick (7)
Start Pause (8)
Door lock light (9)
Delay Start (10)
Ecological hints
Display (11)
First use
10
11
Personalisation
Acoustic signals
Child lock
12
12
12
Daily use
12
12
12
13
13
13
14
14
Guide to use the
instruction manual
Load the laundry
Measure out the detergent
Select the required programme
Select the spin speed or None option
Select the desired options
Select the delay start
The following symbols will be found in the
text to guide you throughout the instructions:
Safety instructions
Start the programme
How to change an option or a programme
Hints and tips
during its cycle
14
15
How to interrupt a programme
How to open the door during the cycle of a
programme 15
Environmental information
5
End of programme
15
16
18
21
22
Helpful hints and tips
Washing programmes
Technical data
Consumption values
Care and cleaning
Descaling
External cleaning
Washing drum
22
22
23
23
24
24
26
26
Door seal
Cleaning the pump
Emergency emptying out
Frost precautions
6
Product description
1 Detergent dispenser drawer
1
2
2 Control panel
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet
3
4
5
6
7
Detergent dispenser drawer
Compartment for detergent used for
prewash and soak phase or for stain remover
used during the stain action phase (if
available). The prewash and soak detergent is
added at the beginning of the wash
programme. The stain remover is added
during the stain action phase.
Compartment for powder or liquid
detergent used for main wash. If using liquid
detergent pour it just before starting the
programme.
Compartment for liquid additives (fabric
softener, starch).
Follow the product manufacturer’s
recommendations on quantities to use and
do not exceed the «MAX» mark in the
detergent dispenser drawer. Any fabric
softener or starching additives must be
poured into the compartment before starting
the wash programme.
Control panel
Below is a picture of the control
panel. It shows the programme
selector dial as well as the buttons
and pilot lights. These are presented
by relevant numbers on the following
pages.
8
11
10
1
2
3
4
5
6
7
8
9
1 Detergent dispenser drawer
2 Programme selector dial
3 Spin button
7 Quick button
8 Start/Pause button
9 Door lock light
4 Prewash button
10 Delay start button
5 Intensive button
11 Display - Wash time
6 Extra rinse button
Prewash: the machine performs a prewash
cycle before the main wash phase. The
washing time will be prolonged. This option
is recommended for heavily soiled laundry.
The prewash ends with a short spin in
programmes for cotton and synthetic
fabrics, whereas in the programme for
delicate fabrics the water is only drained.
Stain: the machine adds a stain phase to the
washing of heavily soiled laundry. The
washing time will be prolonged by a few
minutes.
Programme Dial (2)
It allows you to switch the appliance on/off
and/or to select a programme.
Spin (3)
By pressing this button you can change the
spin speed of the selected programme or to
select the available function (s).
None
By selecting this function all the spinning
phases are cancelled and the last rinse water
is drained. If you set this option with
programmes for cotton, synthetics and
delicates, the machine will perform some
extra rinses.
Pour a stain removing detergent into
the compartment marked
.
This function is available with a temperature
of 40° or higher.
Rinse hold: the machine will not drain the
water of the last rinse, this will ensure the
minimum of creasing to laundry. Before
opening the door the water must be
drained.
Prewash (4)
By pressing this button repeatedly, you can
select only one of the following options:
9
Intensive (5)
Start Pause (8)
By selecting this function the washing
intensity will be increased and the washing
time will be prolonged by a few minutes
depending on the selected temperature.
This option can be selected for heavily soiled
cottons.
This button allows you to start or to
interrupt the selected programme.
Door lock light (9)
The light Door lock shows if you can open
the door:
Extra Rinse (6)
• light on: the door cannot be opened. The
machine in working or has stopped with
water left in the tub.
• light off: the door can be opened. The
programme is finished or the water has
been emptied out.
This appliance is designed to save energy. If
it necessary to rinse the laundry using an
extra quantity of water (extra rinse), select
this option. Some additional rinses will be
performed. This option is recommended for
people who are allergic to detergents, and in
areas where the water is very soft.
Delay Start (10)
The programme can be delayed from 30 min
- 60 min - 90 min, 2 hours and then by 1
hour up to a maximum of 20 hours by
means of this button.
Quick (7)
This option can be used for lightly soiled
laundry. The washing time will be reduced
according to type of fabric and the selected
temperature.
Display (11)
11.1
11.2
The following pieces of information are
shown on the display:
11.1 - Child lock symbol.
11.2
• Duration of washing programme in
hours and minutes, after you have
selected a programme. While the
programme is running (after you have
pressed the button 8), the displayed time
value decreases by one unit every minute.
10
displayed for a few seconds, then the
duration of the selected programme
reappears. After you have pressed the
button 8, the countdown is updated every
hour, and, for the last hour, every minute.
The washing machine has stopped
with water in the tub, at the end of
the «Soak» programme or if the «Rinse
hold» option has been set: this is indicated
by a flashing zero. The «Door lock» pilot
light is still on. The door cannot be
opened.
• An incorrect option selection has
been made: this is indicated by the
message Err for a few seconds when an
option incompatible with the current
programme is selected.
The washing machine has
completed the programme: this is
indicated by a flashing zero. The «Door
lock» pilot light has gone off. It is now
possible to open the door.
• An alarm code indicates a fault with the
machine (see the relevant chapter).
• Delay start, a time value indicated in
hours and selected by the relevant button.
The delay time (20 hours max) is
First use
• Ensure that the electrical and
water connections comply with
the installation instructions.
• Remove the polystyrene block and
any material from the drum.
• Pour 2 litres of water into the main
wash compartment of the
detergent drawer in order to
activate the ECO valve. Then run
a cotton cycle at the highest
temperature without any laundry
in the machine, to remove any
manufacturing residue from the
drum and tub. Pour 1/2 a measure
of detergent into the main wash
compartment and start the
machine.
Download from Www.Somanuals.c1om1. All Manuals Search And Download.
Personalisation
• If enabled before the «Start/Pause»
button is pressed, it prevents the machine
from being started.
• If enabled after pressing the «Start/
Pause» button, it prevents any changes
being made to the programmes or
options selected
To enable or disable this function, press the
buttons 3 and 4 simultaneously for
approximately 6 seconds until the icon
appears on or disappears from the display.
Acoustic signals
The machine is provided with an acoustic
device, which sounds in the following cases:
• at the end of a washing cycle
• if there is a fault
You can deactivate the acoustic signal
(except if there is a fault) by pressing the
buttons 5 and the 6 simultaneously for
about 5 seconds. By pressing these buttons
again the acoustic signal is reactivated.
Child lock
This function works in two different ways:
Daily use
Load the laundry
Measure out the
detergent
Open the door by carefully pulling the door
handle outwards. Place the laundry in the
drum, one item at a time, shaking them out
as much as possible. Close the door.
Measure out the detergent and the
fabric softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent
required, pour it into the main wash
compartment or in the appropriate
compartment if it is required by the selected
programme or option (see more details in
«Detergent dispenser drawer» ).
12
change those values. The green pilot light of
the button 8 starts flashing.
The dial can be turned either clockwise or
counterclockwise. Turn to position «Off» to
reset programme/Switching the machine off.
At the end of the programme the
selector dial must be turned to
position «Off» , to switch the machine
off.
Caution! If you turn the programme
selector dial to another programme
when the machine is working, the
red pilot light of button 8 will blink 3
times to indicate a wrong selection.
The machine will not perform the
new selected programme. The
message Err is displayed for a few
seconds. The machine will not
perform the new selected
If required, pour fabric softener into the
compartment marked (the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
programme.
Select the spin speed or
None option
Press button 3 repeatedly to select the
required spin speed or to select «None»
option. If you select this option, all spinning
phases are suppressed.
The relevant light will light up.
Select the desired
options
Press buttons 4,5,6 and 7 to select the
available options. Depending on the
programme, different options can be
selected together. These must be selected
after choosing the desired programme and
before pressing button 8.
Select the required
programme
Turn the programme dial to the required
programme. The washing machine will
automatically select the maximum spin value
provided for the programme you have
chosen and the display will show the
duration, calculated on the basis of the
maximum load for each type of fabric.
Pressing the corresponding buttons to
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
If an option which is not compatible with the • Press button 8 again.
set wash programme is selected, the red
button 8 light flashes 3 times and the
message Err is displayed for a few seconds.
When the option is set, the relevant light is
on.
The Delay Start cannot be selected with the
draining programme.
Start the programme
To start the selected programme, press the
button 8 ; the green pilot light stops flashing.
If you have selected a delay time, the
countdown will begin and will be shown on
the display.
Select the delay start
Before you start the programme, press this
button repeatedly to select the desired
delay. The set delay time value (up to 20
hours) will appear on the display for a few
seconds, then the duration of the
To interrupt a programme which is running,
press button 8: the green pilot light starts to
flash. To restart the programme from the
point at which it was interrupted, press the
programme will appear again. The wash
programme can be delayed from 30 min - 60 button 8 again. If an incorrect option is
min - 90 min, 2 hours and then by 1 hour up
to a maximum of 20 hours.
You can cancel the delay time at any
moment, before you press the «Start/
Pause» button.
selected, the red pilot light of button 8
flashes 3 times and the message Err is
displayed for a few seconds.
Important!
Selecting the delayed start
You must select this option after you have
set the programme and before you press the
«Start/Pause» button.
You must set the washing machine to Pause
before you make any change in the
programme in progress.
• Select the programme and the required
options.
How to change an option
or a programme during
its cycle
It is possible to change some options
before the programme carries them out.
Before you make any change, you must
pause the washing machine by pressing the
button 8. Changing a running programme is
possible only by resetting it.
Turn the programme selector dial to «Off»
and then to the new programme position.
Start the new programme by pressing the
button 8. The washing water in the tub will
not empty out
• Select the delay start.
• Press button 8: the machine starts its
hourly count down. The programme will
start after the selected delay has expired.
Opening the door throughout the
delay time
If you wish to add laundry in the machine
during the delay time
• Press button 8 to put the machine in
pause.
• Add the laundry, close the door
• Press 8 button again.
Cancelling the delayed start
• Press button 8.
• Press «Delay start» button once until the
symbol «0’» is displayed.
14
display shows a flashing zero «0». It is
possible to open the door.
How to interrupt a
programme
Press the button 8 to interrupt a
programme which is running, the
corresponding green pilot light starts
blinking.
If you had selected an option that ends with
water left in the tub the Door lock light
remains lit to indicate that the water must
be drained before opening the door.
To drain or to spin follow the below
instructions:
Press the same button again to restart the
programme.
1. Turn the programme selector dial to
Off.
How to open the door
during the cycle of a
programme
2. Select the draining or spinning
programme.
3. Reduce the spin speed if needed, by
pressing the relevant button.
You can open the door, after having set the
washing machine to Pause, provided the
following conditions exist:
4. Press button 8.
At the end of the programme, the door can
be now opened. Turn the programme
selector dial to Off to switch the machine
off.
• The washing machine is not in the heating
phase
Remove the laundry from the drum. Check
whether the drum is completely empty, by
rotating it with your hand. The purpose of
this is to prevent any items of laundry from
remaining accidentally in the drum, where
they might get damaged in a subsequent
wash (e.g. by shrinking) or bleed colour into
another load of laundry.
If you do not intend to carry out another
wash, close the water tap. Leave the door
open to prevent the formation of mildew
and unpleasant smells.
• The level of the water is not high;
If these requirements are met, when you
pause the washing machine, the «Door
lock» light goes off and the door can be
opened.
Should it not be possible to open the door,
and should it be absolutely necessary to do
so, switch the machine off by turning the
selector dial to Off. After a few minutes,
you can open the door.
Pay attention to the level and
temperature of the water in the
washing machine! When you close the
door to restart the programme turn the dial
to the previous programme and repeat the
options previously selected and press button
8.
End of programme
At the end of the programme, the washing
machine stops automatically, the button 8
light and the Door lock light go off. The
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
Stand by: once the programme has
finished after a few minutes the
energy saving system is enabled with
the pilot lights switched on. By
pressing any button the appliance will
come out of the energy saving status.
Helpful hints and tips
Sorting out the laundry
Removing stains
Follow the wash code symbols on each
garment label and the manufacturer’s
washing instructions. Sort the laundry as
follows: whites, coloureds, synthetics,
delicates, woollens.
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water.
For dried stains, soak overnight in water
with a special detergent then rub in the soap
and water.
Oil based paint: moisten with benzine
stain remover, lay the garment on a soft
cloth and dab the stain; treat several times.
Dried grease stains: moisten with
turpentine, lay the garment on a soft surface
and dab the stain with your fingertips and a
cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since
the cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Before loading the
laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first
wash; they should therefore be washed
separately the first time.
Make sure that no metal objects are
left in the laundry (e.g. hair clips,
safety pins, pins).
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long
tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove
hooks or tie them up in a bag or net.
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone1), lay the garment on a soft cloth
and dab the stain.
1) do not use acetone on artificial silk
16
If using liquid detergents, a programme
without prewash must be selected.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s
recommendations on quantities to use and
do not exceed the «MAX» mark in
the detergent dispenser drawer.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid, then
rinse. Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone1), then with
acetic acid; treat any residual marks on white
fabrics with bleach and then rinse
thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
Quantity of detergent to
be used
The type and quantity of detergent will
depend on the type of fabric, load size,
degree of soiling and hardness of the water
used.
Follow the product manufacturers’
instructions on quantities to use.
Use less detergent if:
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment.
• you are washing a small load
• the laundry is lightly soiled
Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
• large amounts of foam form during
washing.
Degrees of water
hardness
All commonly available washing machine
detergents may be used in this appliance:
Water hardness is classified in so-called
“degrees” of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority. If the
water hardness degree is medium or high
we suggest you to add a water softener
following always the manufacturer’s
• powder detergents for all types of fabric
• powder detergents for delicate fabrics
(60°C max) and woollens
• liquid detergents, preferably for low
temperature wash programmes (60°C
max) for all types of fabric, or special for
woollens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
instructions. When the degree of hardness is
soft, readjust the quantity of the detergent.
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
Washing programmes
Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Detergent
Compartment
Options
Laundry
2)
Cottons
90° - 60°
SPIN
NONE
Main wash - Rinses
RINSE HOLD
PREWASH
INTENSIVE
STAIN
Maximum spin speed at 1200 rpm
Max. load 6 kg - Reduced load 3 kg
White cotton (heavily or normally soiled items).
QUICK 1)
EXTRA RINSE
2)
Cottons Economy
60°
SPIN
NONE
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 6 kg
RINSE HOLD
PREWASH
STAIN
White or fast colour cotton (normally or slightly
soiled items).
EXTRA RINSE
Energy saving programme: This programme can be
selected for slightly or normally soiled cotton items.
The temperature will decrease and the washing time
will be extended. This allows to obtain a good washing
efficiency by saving energy.
2)
Cottons Economy
40°
SPIN
NONE
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 6 kg
RINSE HOLD
PREWASH
STAIN
White or non fast colour cotton (slightly soiled
items).
EXTRA RINSE
This programme can be selected for slightly or
normally soiled cotton items. The temperature will
decrease and the washing time will be extended. This
allows to obtain a good washing efficiency by saving
energy.
18
Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Laundry
Detergent
Compartment
Options
2)
Cottons
SPIN
40° - 30°
NONE
Main wash - Rinses
RINSE HOLD
PREWASH
INTENSIVE
Maximum spin speed at 1200 rpm
Max. load 6 kg - Reduced load 3 kg
Colour cotton (normally or slightly soiled items).
STAIN3)
QUICK1)
EXTRA RINSE
2)
Synthetics
SPIN
60° - 40° - 30°
NONE
Main wash - Rinses
RINSE HOLD
PREWASH
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1.5 kg
Synthetic or mixed fabrics: underwear, coloured
garments, non-shrink shirts, blouses.
STAIN3)
QUICK1)
EXTRA RINSE
2)
Synthetics Economy
40°
SPIN
NONE
Main wash - Rinses
RINSE HOLD
PREWASH
STAIN
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1.5 kg
Mixed fabrics,shirts, blouses, underwear, coloured
garments, non-shrink shirts.
EXTRA RINSE
2)
Delicates
SPIN
40° - 30°
NONE
Main wash - Rinses
RINSE HOLD
PREWASH
Maximum spin speed 700 rpm
Max. load kg 3 - Reduced load kg 1.5
Delicate fabrics: acrylics, viscose, polyester.
STAIN3)
QUICK1)
EXTRA RINSE
Wool - Hand wash
40° - 30° - Cold
SPIN
NONE
Main wash - Rinses
RINSE HOLD
Maximum spin speed at 900
Max. load 2 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate
fabrics. Note: A single or bulky item may cause
imbalance. If the appliance doesn’t perform the final
spin phase, add more items, redistribute the load
manually and then select the spinning programme.
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Laundry
Detergent
Compartment
Options
Soak
30°
Prewash - Soak for about 40 minutes - Stop with
water in the tub
Max. load 6 kg
Special programme for heavily soiled laundry. The
machine performs a soak at 30°C. At the end of this
time the machine will stop automatically with water
left in the tub. Before starting a new washing phase, it
is necessary to empty out the water by:
• Draining only: turn the programme selector dial
to the draining programme (press then the button
8).
• Draining and spinning: turn the programme
selector dial to spinning programme, reduce the
spin speed by pressing the relevant button, press
then button 8.
Important! This programme cannot be used for very
delicate fabrics as silk or wool. Pour the detergent for
the soak programme into the compartment marked .
At the end of the soak (after having emptied out the
water) you can select the washing programme. (First
turn the programme selector dial to Off, then to the
programme and press the button 8).
Rinse
SPIN
Rinses
NONE
Maximum spin speed at 1200 rpm
Max. load 6 kg
RINSE HOLD
EXTRA RINSE
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs a few rinses, followed by a final
long spin. The spin speed can be reduced.
Drain
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in
programmes with the set option, which ends with
water left in the tub.
20
Programme - Maximum and Minimum
Temperature - Cycle Description - Maximum
Spin Speed - Maximum Fabrics Load - Type of
Laundry
Detergent
Compartment
Options
Spin
SPIN
Drain and long spin
Maximum spin speed at 1200 rpm
Max. load 6 kg
Separate spin for hand washed cotton garments and
after programmes with option Rinse hold. You can
choose the spin speed by pressing the relevant button
to adapt it to the fabrics to be spun.
30 Minute wash
30°
SPIN
NONE
Main wash - Rinses
Maximum spin speed 900 rpm
Max. load kg 2
Short cycle for lightly soiled fabrics.
Off
For cancelling the programme which is running or to switch the machine off .
1) If you select the Quick option by pressing button 4, we recommend that you reduce the maximum load as
indicated. Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
3) «Stain» option is available only at a temperature of 40°C or higher.
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
60 cm
63 cm
Depth (Overall dimensions)
Electrical connection
Information on the electrical connection is given on the rating
Voltage - Overall power - Fuse plate, on the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
6 kg
Maximum
1200 rpm
Download from Www.Somanuals.c2om1. All Manuals Search And Download.
Consumption values
Programme1)
Energy consumption
Water consumption
(litre)2)
(KWh)2)
White Cottons 95 °C
2.1
62
59
59
44
57
57
Cottons 60 °C
1.35
0.75
0.5
Cottons 40 °C
Synthetics 40 °C
Delicates 40 °C
0.55
0.3
Wool/ Handwash 30 °C
1) Refer to the display for the programme time.
2) The consumption information shown in this chart is indicative. It can vary depending on the quantity and the type
of laundry, on the temperature of the water supply and on the ambient temperature.
efficient programmes in terms of combined
energy and water consumption for washing
that type of cotton laundry.
They agree with EN60456.
Standard programmes for the
Energy Label consumption
values
The cotton 60 °C economy and cotton 40
The actual water temperature may
differ from the declared cycle
temperature.
°C economy are the standard cotton
programmes for normally soiled cotton
laundry. They are suitable to clean normally
soiled cotton laundry and they are the most
Care and cleaning
You must DISCONNECT the appliance
from the electricity supply, before you can
carry out any cleaning or maintenance work.
After each wash
Leave the door open for a while. This helps
to prevent mould and stagnant smells
forming inside the appliance. Keeping the
door open after a wash will also help to
preserve the door seal.
Descaling
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
Maintenance wash
With the use of low temperature washes it
is possible to get a build up of residues inside
the drum.
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
22
We recommend that a maintenance wash
be performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash
programme.
• Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry
thoroughly.
Important! Do not use methylated spirits,
solvents or similar products to clean the
cabinet.
Cleaning the drawer
recess
Having removed the drawer, use a small
brush to clean the recess, ensuring that all
washing powder residue is removed from
the upper and lower part of the recess.
Cleaning the dispenser
drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Washing drum
Rust deposits in the drum may occur due to
rusting foreign bodies in the washing or tap
water containing iron.
To aid cleaning, the top part of the additive
compartment should be removed.
Download from Www.Somanuals.c2om3. All Manuals Search And Download.
Important! Do not clean the drum with
acidic descaling agents, scouring agents
containing chlorine or iron or steel wool.
Warning! Before opening the pump
door, switch the appliance off and
remove the mains plug from the
socket.
1. Remove any rust deposits on the drum
with a cleaning agent for stainless steel.
Proceed as follows:
2. Run a washing cycle without any
washing to clean off any cleaning agent
residues.
1. Unplug the appliance.
2. If it is necessary, wait until the water has
cooled down.
Programme: Short Cotton Programme
at maximum temperature and add
approx. 1/4 measuring cup of
detergent.
3. Open the pump door levering on the
groove with a coin (or with the suitable
tool, that you can find in the bag
containing the instruction booklet
depending on the model).
Door seal
Check from time to time the door seal and
possible objects that could be trapped in the
fold.
1
2
4. Place a container close to the pump to
collect any spillage.
5.
Cleaning the pump
The pump should be inspected regularly and
particularly if:
6. Pull out the emergency emptying cap
from the filter cover, using pliers.
• the appliance does not empty and/or
spin;
• the appliance makes an unusual noise
during draining due to objects such as
safety pins, coins etc. blocking the pump.
• a problem with water draining is detected
(see chapter “What to do if...” for more
details).
24
7. When no more water comes out,
unscrew the pump cover by turning it
anti-clockwise, using pliers, and remove
the filter. Always keep a towel nearby
to dry up any water spillage when
removing the cover.
Clean the filter under a tap, to remove
any traces of fluff.
11. Replace the emergency emptying cap
into the filter cover and fix it firmly.
2
1
8. Remove foreign bodies and fluff from
the pump seat and from the pump
impeller.
12. Close the pump door.
9. Check carefully whether the pump
impeller rotates (it rotates jerkily). If it
doesn’t rotate, please contact your
Service Centre.
Warning!
When the appliance is in use and depending
on the programme selected there can be
hot water in the pump.
Never remove the pump cover during a
wash cycle, always wait until the appliance
has finished the cycle, and is empty. When
refitting the pump cover, ensure it is
securely re-tightened so as to stop leaks and
young children being able to remove it.
10. Replace the filter into the pump by
inserting it correctly into the special
guides. Screw the pump cover firmly by
turning it clockwise.
Download from Www.Somanuals.c2om5. All Manuals Search And Download.
8. Turn on the water tap.
Cleaning the water inlet
filters
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power
socket;
Warning! If the appliance doesn't fill
or it is taking longer to fill with water,
check if the water inlet filters are
blocked.
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle
brush.
4. open the pump door;
5. place a bowl on the floor. Remove the
emergency emptying cap from the filter.
The water should drain by gravity into
the bowl. When the bowl is full, refit
the cap into the filter. Empty the bowl.
Repeat the procedure until water stops
flowing out;
6. clean the pump if necessary as
previously described;
7. screw the pump again and close the
door.
Frost precautions
4. Screw the hose back onto the tap.
If the machine is installed in a place where
the temperature could drop below 0°C,
proceed as follows:
5. Unscrew the hose from the machine.
Keep a rug nearby because some water
may flow.
1. Pull out the plug from the power
socket.
2. Turn off the water tap.
3. Unscrew the inlet hose.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
4. Place the end of the inlet hose in a bowl
placed on the floor, open the
emergency emptying cup of the filter
and let water drain out.
5. Refit the emergency emptying cap into
the filter and screw the water inlet hose
back.
6. When you intend to start the machine
up again, make sure that the room
temperature is above 0°C.
7. Screw the hose back to the machine
and make sure the connection is tight.
26
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main
wash compartment of the detergent drawer
and then run the drain programme. This will
avoid wasting detergent on the next wash
programme.
Download from Www.Somanuals.c2om7. All Manuals Search And Download.
Installation
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging,
carefully lay machine on it’s back to
remove the polystyrene base from the
bottom.
3. Unscrew the three bolts.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
4. Slide out the relevant plastic spacers.
28
5. Open the porthole and remove the
polystyrene block fitted on the door
seal.
should protrude a few centimetres beyond
the edges of the machine.
Warning! The machine should
NOT be placed on deep pile
carpeting.
Level the washing machine by raising or
lowering the feet. The feet may be tight to
adjust as they incorporate a self locking nut,
but the machine MUST be level and stable.
If necessary, check the setting with a spirit
level. Any necessary adjustment can be
made with a spanner. Accurate levelling
prevents vibration, noise and displacement
of the machine during operation.
6. Fill the smaller upper hole and the two
large ones with the corresponding
plastic plug caps supplied in the bag
containing the instruction booklet.
Some vibration is inevitable, especially if
mounted on a wooden floor. Sprung
wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If
possible, always place the machine on a solid
floor.
Positioning and levelling
Install the machine on a flat hard floor. Make
sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check
that the machine does not touch the wall or
other kitchen units.
Plumbing in
Your new washing machine has been
designed to be permanently plumbed in to
your home’s water supply and drainage
system. However, if this is not possible, it
may be connected to a suitable existing tap
with the drain hose discharging into a sink.
The appliance has an inlet hose, with female
3/4” BSP thread connector. If this
Caution! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
If the floor is carpeted or covered with
crumbly or soft material, insert a rigid
support base under the feet to prevent
noise, vibration or displacement. The base
connection is not compatible with the
plumbing of the existing installation, a variety
Download from Www.Somanuals.c2om9. All Manuals Search And Download.
of connectors are available from good
hardware stores and plumbers merchants to
suit most domestic plumbing. Any alteration
to your existing plumbing must be carried
out by a competent person, or qualified
plumber.
Water inlet
Warning! This appliance must
be connected to a cold water
supply.
The inlet hose is screwed to the back of the
appliance.
The inlet hose must not be lengthened. If it
is too short and you do not wish to move
the tap, you will have to purchase a new,
longer hose specially designed for this type
of use.
1. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks. Always use the hose
supplied with the appliance.
Warning! Installation should
comply with local water
authority and building
regulations’ requirements.
The appliance must be
Important! Do not place the inlet
hose downwards. Angle the hose to
the left or right depending on the
position of your water tap as
indicated in the picture.
connected to a cold water
supply.
A minimum water pressure of 0.05
MPa (0.5 bar) is required for safe
operation of the appliance.
If you cannot make the cold water
connection direct from the rising
mains, you may be able to operate
the appliance from your cold water
storage system.
There should be a minimum vertical
distance of 5.02 m (16.5 ft) between
the appliance’s inlet and the bottom
of the water storage tank.
35°
45°
2. Connect the water inlet hose supplied
with the machine to a tap with a 3/4"
thread. Installation should comply with
local water authority and building
regulations’ requirements.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system
using one of the following methods.
30
1. Into a drainage standpipe
Firstly form a hook in the end of the drain
hose using the “U” piece” supplied.
local Service Force Centre. The joining piece
must have an internal diameter of 18 mm.
If your drain hose looks like this (see below)
you do not require the “U” piece”. Just push
the hose firmly in to the standpipe.
1
Place the drain hose into your standpipe,
which should have an internal diameter of
approximately 38 mm thus ensuring there is
an air break between the drain hose and
standpipe.
2. Onto a sink outlet spigot.
If the outlet spigot has not been used
before, remove any blanking plug that may
be in place.
38 mm (½”)
When discharging into a standpipe ensure
that the top of the standpipe is no more
than 90 cm (35.4'') and no less than 60 cm
(23.6'') above floor level.
3 pin
Push the drain hose onto the spigot and
secure with a clip, ensure a loop is formed in
the drain hose (see diagram) to prevent
waste from the sink entering the appliance.
If you intend to drain the hose from the
machine into a sink, make sure that the sink
is empty and the plug hole is not blocked.
Use the plastic “U - Piece” supplied.
The drain hose may be extended to a
maximum of 4 metres. An additional drain
hose and joining piece is available from your
Download from Www.Somanuals.c3om1. All Manuals Search And Download.
should protrude a few centimetres beyond
the edges of the appliance.
Warning! The appliance should
NOT be placed on deep pile
carpeting.
Note!
Please ensure that when the
appliance is installed it is easily
accessible for the engineer in the
event of a breakdown.
In the interest of the
environment
Important! Before connecting up the
machine to new pipework or to pipework
that has not been used for some time, run
off a reasonable amount of water to flush
out any debris that may have collected in the
pipes.
The appliance should be connected to the
FOUL drainage system, the water will then
be taken to a sewage works for treatment
before being discharged safely into a river.
It is essential that these appliances are not
connected to the surface water drainage
system as this water is discharged directly
into a river or stream and may cause
pollution.
Special conditions
If the floor is carpeted or covered with
crumbly or soft material, insert a rigid
support base under the feet to prevent
noise, vibration or displacement. The base
If you require any further advice please
contact your local water authority.
32
SHOWER
SINK TOILET
BATH
BIDET
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
UNTREATED
DISCHARGE
TREATED
DISCHRGE
RIVER
RIVER
Warning! THIS APPLIANCE
MUST BE EARTHED.
Electrical connection
Any electrical work required to install this
appliance should be carried out by a
The manufacturer declines any
liability should this safety
measure not be observed.
Before switching on, make sure the
electricity supply voltage is the same
as that indicated on the appliance’s
rating plate.
qualified electrician or competent person.
Download from Www.Somanuals.c3om3. All Manuals Search And Download.
The wire coloured brown must be
connected to the terminal marked «L» or
coloured red.
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer sheath.
Important! Information on the
electrical connection is given on the
rating plate on the inner edge of the
appliance door.
The appliance is supplied with a 13 amp plug
fitted.
In the event of having to change the fuse in
the plug supplied, a 13 amp ASTA approved
(BS1363/A) fuse must be used.
Should the plug need to be replaced for any
reason, proceed as described below.
The wires in the mains lead are coloured in
accordance with the following code:
1 Green and Yellow - Earth
2 Brown- Live
Warning! A cut off plug
inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is
disposed of safely. Should the
appliance power supply cable
need to be replaced, this must
be carried out by our Service
Force Centre.
The appliance should not be
connected to the electrical
supply by means of an extension
cable.
3 Cord Clamp
4 Blue- Neutral
1
Note!
When the appliance is installed the power
supply cable must be accessible.
Permanent connection
in the case of permanent connection it is
necessary that you install a double pole
switch between the appliance and the
electricity supply (mains), with a minimum
gap of 3 mm between the switch contacts
and of a type suitable for the required load
in compliance with the current electrical
regulations.
2
4
3
The wire coloured green and yellow must
be connected to the terminal marked with
the letter «E» or by the earth symbol or
coloured green and yellow.
The switch must not break the yellow and
green earth cable at any point.
The wire coloured blue must be connected
to the terminal «N» or coloured black.
34
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
display and some acoustic signals sound to
indicate that the machine is not working:
• E10: problem with the water supply
• E20: problem with water draining
• E40: door open
Once the problem has been eliminated,
press the button 8 to restart the
programme. If after all checks, the problem
persists, contact your local Service Force
Centre.
Important! if you call out an engineer to a
fault listed below, or to repair a fault caused
by incorrect use or installation, a charge will
be made even if the appliance is under
guarantee.
During machine operation it is possible that
the red Start/Pause pilot light flashes, one
of the following alarm codes appears on the
Problem
Possible cause/Solution
The door has not been closed (E40) .
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse or the fuse in a plug has blown.
The washing machine
does not start:
• Replace the fuse.
The button 8 has not been pressed.
• Please press the button 8 again.
The «Delay start» option has been selected.
• Please cancel the Delay start.
The «Child lock» option has been enabled.
• Disable the Child lock.
Download from Www.Somanuals.c3om5. All Manuals Search And Download.
Problem
Possible cause/Solution
The water tap is closed (E10).
• Open the water tap.
The inlet hose is squashed or kinked (E10).
• Check the inlet hose connection.
The machine does not fill: The filter in the inlet hose or the inlet valve filter is blocked (E10).
• Clean the water inlet filters (See «Cleaning the water inlet
filters» for more details).
The door is not properly closed (E40) .
• Close the door firmly.
The drain hose is squashed or kinked (E20).
• Check the drain hose connection.
The drain filter is clogged (E10) .
The machine does not
empty and/or does not
spin:
• Clean the drain filter.
An option or a programme that ends with the water still in the tub
or that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
The end of drain hose is too low.
The end of drain hose is submerged in water.
There is no vent in the end of drain hose.
The machine fills than
empties out immediately:
• Refer to relevant paragraph in "Water drainage" section.
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose
fittings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
There is water on the
floor:
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The emergency emptying cap has not been replaced into the filter
or the filter has not been properly screwed in after cleaning action.
• Refit the emergency emptying cap into the filter or screw the
filter fully in.
36
Problem
Possible cause/Solution
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
Unsatisfactory washing
results:
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released. (Door lock pilot light is on)
The door will not open:
• Wait the door release.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
The machine vibrates /
The machine is noisy:
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen
several times before the unbalance disappears and normal spinning
can resume. If, after 10 minutes, the laundry is still not evenly
distributed in the drum, the machine will not spin. In this case,
redistribute the load manually and select the spin programme.
Spinning starts late or the
machine does not spin:
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor
ensures a softer start and more even distribution of the laundry in
the drum when spinning, as well as increased stability of the
machine.
The machine makes an
unusual noise:
No water is visible in the
drum:
Machines based on modern technology operate very economically
using very little water without affecting performance.
Download from Www.Somanuals.c3om7. All Manuals Search And Download.
Repairs - After Sales Service
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Repairs - After Sales
Service
Your appliance comes with a three year
warranty.
If it is not working correctly; consult the fault
finding guides within this instruction book
("What to do if ..."). If a fault occurs which
you can not resolve through following the
advice and information contained within this
instruction manual, the next step is to
contact our extended warranty
• Mod.......................................
• P.N.C.....................................
• S.N.........................................
Please retain your purchase receipt safely for
the service engineer to verify the purchase
details.
Important! If you call out an engineer to a
fault listed above, or to repair a fault caused
by incorrect use or installation, a charge will
be made even if the appliance is under
guarantee.
administrators on:
0844 871 7771
They will give you details for your local
Service engineer. Before calling out an
engineer, please ensure you have read the
details under the heading “What to do if...”.
When you contact the local service engineer
you will need to give the following details:
Spare parts
Always insist on genuine spare parts.
An authorised service engineer should
service this product, and only genuine spare
parts should be used. Under no
1. Your name, address and post code
2. Your telephone number
circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or
serious malfunctioning. Contact your local
John Lewis Branch.
3. Clear and concise details of fault
4. The purchase date as found on your
receipt
5. The model number, product number
and serial number of the appliance
(found on the rating plate - see picture)
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
38
Environment concerns
• With adequate pre-treatment, stains and
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
limited soiling can be removed; the
laundry can then be washed at a lower
temperature.
• Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
Packaging materials
The materials marked with the symbol
are recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
Ecological hints
To save water, energy and to help protect
the environment, we recommend that you
follow these tips:
• Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the
environment is protected too!).
• The machine works more economically if
it is fully loaded.
Download from Www.Somanuals.c3om9. All Manuals Search And Download.
|