John Deere Compact Loader 310SE User Manual

S
P
E
C
I
F
I
C
A
T
I
O
N
S
ENGINE  
310SE  
Type.............................................................................................................................John Deere 4045T – Turbocharged  
Rated power @ 2,200 rpm ........................................................................................88 SAE gross hp (66 kW)  
80 SAE net hp (60 kW)  
Cylinders.....................................................................................................................4  
Displacement.............................................................................................................276 cu. in. (4.524 L)  
Fuel consumption, typical........................................................................................1.3 to 2.3 gal./hr. (4.9 to 8.7 L/h)  
Torque rise .................................................................................................................42 percent  
Maximum net torque.................................................................................................271 lb.-ft. (368 Nm)  
Lubrication..................................................................................................................pressure system with spin-on filter and cooler  
Air cleaner..................................................................................................................dual stage dry type with safety element and precleaner  
Electrical system.......................................................................................................12 volt with 65-amp alternator  
Sucker-type cooling fan  
four-speed, helical cut gear, collar shift transmission synchronized in all gears with hydraulic  
reverser  
TRANSMISSION  
Torque converter, single stage, dual phase with  
2.63:1 stall ratio...................................................................................................11 in. (280 mm)  
Travel speeds with 19.5L-24 rear tires Forward  
Reverse  
Gear 1...................................................................................................................3.6 mph (5.8 km/h)  
Gear 2...................................................................................................................5.9 mph (9.5 km/h)  
Gear 3...................................................................................................................14.4 mph (23.2 km/h)  
Gear 4...................................................................................................................24.4 mph (39.3 km/h)  
4.0 mph (6.4 km/h)  
6.6 mph (10.6 km/h)  
16.1 mph (25.9 km/h)  
27.2 mph (43.8 km/h)  
heavy-duty, inboard planetary final drives evenly distribute shock loads over three gears  
hydraulic wet disk, mounted inboard, self adjusting and self equalizing  
FINAL DRIVES  
BRAKES  
CAPACITIES  
Fuel tank (with ground level fueling)......................................................................36 gal. (136 L)  
Engine coolant...........................................................................................................17 qt. (16 L)  
Engine oil including filter..........................................................................................9 qt. (8.5 L)  
Torque converter and transmission.......................................................................15 qt. (14 L)  
Hydraulic system.......................................................................................................24 gal. (91 L)  
Rear axle.....................................................................................................................3.5 gal. (13 L)  
Mechanical-front-wheel-drive axle.......................................................................2.3 gal. (8.5 L)  
hydrostatic power steering and emergency steering conform to ISO5010  
STEERING  
Non-powered axle  
Curb turning radius with brakes ......................................................................11 ft. 9 in. (3.57 m)  
Without brakes............................................................................................13 ft. 3 in. (4.04 m)  
Bucket clearance circle with brakes .............................................................31 ft. 6 in. (9.61 m)  
Without brakes............................................................................................34 ft. 7 in. (10.55 m)  
Steering wheel turns, stop to stop ..................................................................2.3 to 3.0  
Mechanical-front-wheel-drive  
Curb turning radius with brakes ......................................................................10 ft. 11 in. (3.34 m)  
Without brakes ............................................................................................13 ft. 8 in. (4.17 m)  
Bucket clearance circle with brakes .............................................................29 ft. 9 in. (9.07 m)  
Without brakes............................................................................................35 ft. 3 in. (10.74 m)  
Steering wheel turns, stop to stop ..................................................................2.5  
Axle oscillations stop to stop, both axles..............................................................22 degrees  
Axle ratings (SAE J43)  
Front .....................................................................................................................18,860 lb. (8555 kg)  
Rear ......................................................................................................................13,670 lb. (6200 kg)  
HYDRAULIC SYSTEM  
System.........................................................................................................................open center  
Pressure  
Backhoe...............................................................................................................3,625 psi (25 000 kPa)  
Loader ..................................................................................................................3,000 psi (20 700 kPa)  
Pump............................................................................................................................gear type, tandem with unloader  
Flow @ 2,200 rpm  
Backhoe...............................................................................................................36 gpm (136 L/min.)  
Loader ..................................................................................................................28 gpm (106 L/min.)  
Filter, return oil...........................................................................................................10-micron, spin-on enclosed replaceable element  
16  
 
L
I
F
T
C
A
P
A
C
I
T
I
E
S
*
/
D
I
M
E
N
S
I
O
N
S
*Lift capacities are over-end values in lb. (kg) according to SAE J31. Figures listed are 87% of the maximum lift force available. Base vehicle includes counterweight.  
310SE BACKHOEWITH  
TANDARD IPPERSTICK  
310SE BACKHOEWITH 3-FT. 6-IN. (1.07  
M
)
310SE BACKHOEWITH 3-FT. 6-IN. (1.07  
M)  
S
D
E
XTENDABLE IPPERSTICK, RETRACTED  
D
E
XTENDABLE IPPERSTICK, EXTENDED  
D
(SEE PAGE 19.)  
DIMENSIONS  
ROPS and cab  
18  
 
D
I
M
E
N
S
I
O
N
S
BACKHOE  
310SE  
With Standard  
Backhoe*  
With Extendable Dipperstick*  
Retracted  
Extended  
A
B
C
D
E
Loading height, truck loading position ..................................................................11 ft. 3 in. (3.43 m)  
Reach from center of swing pivot..........................................................................18 ft. 3 in. (5.56 m)  
Reach from center of rear axle...............................................................................21 ft. 9 in. (6.63 m)  
Maximum digging depth...........................................................................................14 ft. 6 in. (4.42 m)  
Digging depth (SAE):  
11 ft. 7 in. (3.53 m)  
18 ft. 7 in. (5.66 m)  
22 ft. 1 in. (6.73 m)  
14 ft. 11 in. (4.55 m)  
14 ft. 1 in. (4.29 m)  
21 ft. 11 in. (6.68 m)  
25 ft. 4 in. (7.72 m)  
18 ft. 5 in. (5.61 m)  
(1) 2-ft. (610 mm) flat bottom....................................................................................14 ft. 4 in. (4.37 m)  
(2) 8-ft. (2440 mm) flat bottom..................................................................................13 ft. 4 in. (4.06 m)  
Ground clearance, minimum...................................................................................13 in. (330 mm)  
Bucket rotation..........................................................................................................190 degrees  
Transport height........................................................................................................11 ft. 6 in. (3.51 m)  
Overall length, transport ..........................................................................................23 ft. 6 in. (7.16 m)  
Stabilizer width – transport with ROPS .................................................................7 ft. 2 in. (2.18 m)  
Stabilizer spread – operating..................................................................................10 ft. 2 in. (3.10 m)  
Stabilizer overall width – operating .......................................................................11 ft. 7 in. (3.53 m)  
Width over tires.........................................................................................................86 in. (2.18 m)  
*Backhoe specifications are with 24-in. x 7.5-cu. ft. (610 mm x 0.21 m3) bucket.  
14 ft. 9 in. (4.50 m)  
13 ft. 9 in. (4.19 m)  
13 in. (330 mm)  
18 ft. 3 in. (5.56 m)  
17 ft. 6 in. (5.33 m)  
13 in. (330 mm)  
F
G
H
I
190 degrees  
190 degrees  
11 ft. 5 in. (3.48 m)  
23 ft. 6 in. (7.16 m)  
7 ft. 2 in. (2.18 m)  
10 ft. 2 in. (3.10 m)  
11 ft. 7 in. (3.53 m)  
86 in. (2.18 m)  
11 ft. 5 in. (3.48 m)  
23 ft. 6 in. (7.16 m)  
7 ft. 2 in. (2.18 m)  
10 ft. 2 in. (3.10 m)  
11 ft. 7 in. (3.53 m)  
86 in. (2.18 m)  
J
K
L
M
LOADER PERFORMANCE WITH BUCKET OPTIONS  
1.25 cu. yd.  
(0.96 m3) Heavy-  
duty Long Lip  
1.30 cu. yd.  
1.12 cu. yd.  
(0.86 m3)  
Multipurpose  
1.25 cu. yd.  
(0.96 m3)  
Multipurpose  
(1.00 m3) Heavy-  
duty Long Lip  
single lever  
Operator control........................................................................................................single lever  
Breakout force...........................................................................................................8,817 lb. (39.2 kN)  
Lifting capacity, full height.......................................................................................6,247 lb. (2836 kg)  
Height to bucket hinge pin, maximum ...................................................................11 ft. 2 in. (3.40 m)  
Dump clearance, bucket at 45 degrees ................................................................8 ft. 2 in. (2.59 m)  
Bucket dump angle, maximum................................................................................45 degrees  
Reach at full height, bucket at 45 degrees ...........................................................36.0 in. (911 mm)  
Rollback angle at ground level ...............................................................................40 degrees  
Digging depth below ground, bucket level...........................................................5.8 in. (147 mm)  
Raising time to full height.........................................................................................4.9 sec.  
Bucket dump time .....................................................................................................1.1 sec.  
Bucket lowering time (power down) .....................................................................1.9 sec.  
single lever  
single lever  
8,900 lb. (39.6 kN)  
6,150 lb. (2790 kg)  
11 ft. 2 in. (3.40 m)  
8 ft. 8 in. (2.64 m)  
45 degrees  
8,325 lb. (37.0 kN)  
5,900 lb. (2676 kg)  
11 ft. 2 in. (3.40 m)  
8 ft. 7 in. (2.62 m)  
45 degrees  
8,300 lb. (36.9 kN)  
5,800 lb. (2631 kg)  
11 ft. 2 in. (3.40 m)  
8 ft. 7 in. (2.62 m)  
45 degrees  
a
b
c
d
e
f
30.1 in. (765 mm)  
40 degrees  
32.2 in. (818 mm)  
40 degrees  
32.2 in. (818 mm)  
40 degrees  
8.1 in. (206 mm)  
4.9 sec.  
7.3 in. (185 mm)  
4.9 sec.  
7.3 in. (185 mm)  
4.9 sec.  
1.1 sec.  
1.1 sec.  
1.1 sec.  
1.9 sec.  
1.9 sec.  
1.9 sec.  
LIFT CAPACITY WITH QUICK COUPLER/FORKS  
A1 Maximum height........................................................................................................4,178 lb. (1897 kg)  
B1 Maximum reach.........................................................................................................6,191 lb. (2810 kg)  
C1 At ground line.............................................................................................................8,232 lb. (3737 kg)  
D1 Below ground line.....................................................................................................4.4 in. (112.7 mm) to bottom of tine / 2.7 in. (68.3 mm) to top of tine  
19  
 
A
D
D
I
T
I
O
N
A
L
E
Q
U
I
P
M
E
N
T
310SE  
310SE  
310SE  
Backhoe bucket coupler for “C” and “D” series John  
Deere buckets, Case buckets, and Cat buckets  
Extendable dipperstick, 3 ft. 6 in. extension  
Auxiliary backhoe valve for swingers, thumbs, etc.  
Auxiliary backhoe valve for hammers, compactors  
Auxiliary backhoe plumbing for hammers, compactors  
SAE controlled load lowering device valves  
Fuel gauge, illuminated electric  
Gauge package, illuminated electric – Engine coolant  
temperature / Transmission oil temperature / Alternator  
volts / Fuel gauge  
Monitor system with audible and visual warning – Engine  
air filter restriction indicator / Alternator indicator /  
Engine coolant temperature indicator with audible  
warning / Engine oil pressure indicator with audible  
warning / Hydraulic filter restriction indicator / Torque  
converter oil temperature indicator / Parking brake on/  
off indicator with audible warning / Seat belt indicator /  
Mechanical-front-wheel-drive on/off indicator / Beacon  
on/off indicator  
ENGINE  
John Deere Model 4045T – 4.5 liter, 80 SAE net hp turbo-  
charged, isolation mounted  
Vertical spin-on engine oil filter  
Spin-on John Deere fuel filter with water separator  
Oil-to-water engine oil cooler  
Antifreeze, –34°F (–37°C)  
Coolant recovery tank  
Serpentine belt with automatic belt tensioner  
Sucker-type cooling fan  
Enclosed safety fan guard  
High ambient temperature engine cooling  
Dual element dry-type air cleaner  
Muffler, underhood with curved-end exhaust stack  
Chrome exhaust extension  
Electric ether starting aid  
Engine coolant heater, 1,000 watts  
LOADER  
Hydraulic self leveling  
Return-to-dig feature  
Single-lever control with electric clutch cutoff switch  
Bucket-level indicator  
Loader boom service lock  
Auxiliary loader hydraulics with two-lever control  
Loader front coupler  
Seats and seat belts  
Non-suspension vinyl swivel seat without armrests  
Suspension vinyl swivel seat with armrests and lumbar  
support  
Suspension fabric swivel seat with armrests and  
lumbar support  
Air suspension vinyl swivel seat with armrests and  
lumbar support  
Air suspension fabric swivel seat with armrests and  
lumbar support  
2-in. seat belt with retractors  
3-in. seat belt with retractors  
Cab  
Headliner  
Dome light  
Left cab door  
Right cab door  
Tinted safety glass  
Two front and one rear windshield wipers  
Front windshield washer  
Fresh air intake heater/defroster/pressurizer – 40,000  
Btu/hr. (11.7 kW) heater  
Air conditioning – 26,000 Btu/hr. (7.6 kW) output / CFC-  
free R134a refrigerant  
65-amp alternator  
Loader buckets  
Less bucket, with bucket pins  
Heavy-duty buckets with bolt-on cutting edge, skid  
plates, and lift loops  
Multipurpose buckets with bolt-on cutting edge, skid  
plates, and lift loops  
POWER TRAIN  
Powershift transmission – Torque converter with electri-  
cally actuated twist grip F-N-R in 1st through 4th gears  
Transmission with powershift reverser and torque con-  
verter – Fully synchronized four forward, four reverse  
speeds / Isolation mounted to mainframe  
Transmission oil cooler  
Vertical spin-on transmission filter  
Electric forward-neutral-reverse control lever with  
neutral safety switch interlock  
Electric clutch cutoff on gearshift and loader levers  
Differential lock, electric foot-actuated  
Planetary final drives  
Hydraulic service brakes – Inboard, wet multi-disc, self  
adjusting and self equalizing / Conform to SAE J1473  
Parking/emergency brake with electric switch control –  
Spring applied, hydraulically released wet multi-disc /  
Independent of service brakes / Conforms to SAE J1473  
Hydrostatic power steering with emergency manual mode  
Non-powered front axle  
Mechanical-front-wheel-drive with limited slip differential –  
Electric on/off control / Drive-shaft guard / Sealed axle  
Tires  
11L-15 F3 front tires  
11L-16 F3 front tires  
12.5/80-18 traction front tires  
16.9-24 R4 rear tires  
19.5L-24 R4 rear tires  
Rear wheel spacers for use with chains  
HYDRAULIC SYSTEM  
36 gpm (136 L/min.) tandem gear pump, open center system  
Independent hydraulic reservoir  
Hydraulic oil cooler  
“O”-ring face seal connectors  
10-micron vertical spin-on filter  
ELECTRICAL  
12-volt system  
65-amp alternator  
Single battery with 150-min. reserve capacity and 750 CCA  
Dual batteries with 300-min. reserve capacity and 1,500 CCA  
Positive terminal battery cover  
Blade-type multi-fused circuits  
By-pass start safety cover on starter  
LIGHTS  
Two front halogen driving/work lights, 32,500 candle-  
power each  
95-amp alternator  
AM/FM/weatherband radio  
Ride control  
Two additional front halogen work lights, 32,500 candle-  
power each  
Two rear halogen work lights, 32,500 candlepower each  
Two front and two rear turn signal/flashing  
Two rear stop and tail  
OVERALL VEHICLE  
One-piece unitized construction mainframe  
Vehicle tiedowns, two front and one rear  
Remote grease bank for front axle  
Rigid mounted front bumper  
Front counterweights  
400 lb. (181 kg)  
650 lb. (295 kg)  
900 lb. (408 kg)  
1,150 lb. (522 kg)  
Two rear reflectors  
Rotating beacon  
OPERATOR’S STATION  
BACKHOE  
Modular-design ROPS/FOPS canopy with molded roof –  
Isolation mounted / Conforms to SAE J1040  
Left and right front access  
Slip-resistant steps and ergonomically located handholds  
Molded floor mat  
Backhoe with standard dipperstick, 14 ft. 6 in. digging depth  
Backhoe controls  
Two-lever (Deere) controls  
Three-lever (Case) controls  
Four-lever (Ford) controls  
SAE excavator two-lever controls  
Backhoe transport lock lever  
Swing lock pin stored in operator’s station  
Stabilizer valve with two-direction anti-drift valves  
Pivoting stabilizers  
With dirt pads  
With reversible pads  
Stabilizer cylinder guards  
Backhoe buckets  
1,400 lb. (635 kg)  
Fuel tank, 36 gal. (136 L), ground level fueling  
Engine sideshields with sliding service access door  
Front grille screen  
Vandal protection for instrument panel, engine access  
doors, and fuel tank  
Reverse warning alarm – Switchable to 97 dB(A) or  
111 dB(A)  
Dent-resistant rear fenders  
Rear fender extensions  
Front fenders*  
SMV emblem  
Rental decal kit  
Special color paint*  
Headliner  
Coat hook  
Built-in beverage and Thermos® bottle holders  
Built-in Operator’s Manual storage compartment with manual  
Interior rearview mirror  
Outside rearview mirrors  
Hand throttle with fuel economy setting at 2,100 rpm  
Suspended foot throttle  
Tilt steering  
Horn  
Key start switch with electric fuel shutoff  
Hourmeter, illuminated electric  
Tachometer/hourmeter, illuminated electric  
Less bucket, with bucket pins  
Standard duty with lift loops  
Heavy duty with lift loops  
Severe duty with lift loops  
Quarter cab*  
KEY:  
Standard equipment  
Optional or special equipment  
*See your John Deere dealer for further information.  
Net engine power is with standard equipment including air cleaner, exhaust system,  
alternator, and cooling fan, at standard conditions per SAE J1349 and DIN 70 020,  
using No. 2-D fuel at 35 API gravity. No derating is required up to 10,000 feet (3050 m).  
Gross power is without cooling fan.  
Specifications and design subject to change without notice. Wherever applicable, specifications are in  
accordance with SAE standards. Except where otherwise noted, these specifications are based on a unit  
with 19.5L-24, 8 PR R4 rear tires, 11L-16, 12 PR F3 front tires, 1.12 cu. yd. (0.86 m3) loader bucket, and  
24 in. x 7.5 cu. ft. (610 mm x 0.21 m3) backhoe bucket.  
20  
DKA310SE Litho in U.S.A. (00-03)  
 

InFocus Projector W60 User Manual
Insignia Video Game Console NS 32D510NA15 User Manual
Jensen DVD Player DVDB01 User Manual
Johnson Controls Automobile Parts M9220 GGX 3 User Manual
JVC Answering Machine GR DVL105 User Manual
JVC Car Stereo System KW R500 User Manual
Jwin Telephone JT P433 User Manual
Kalorik Hot Beverage Maker JK 39825 User Manual
Kenwood Car Video System DDX7029 User Manual
Kobe Range Hoods Ventilation Hood RA9436SQF User Manual