Rev. 082113
ONSTAR RADIO REPLACEMENT FOR SELECT GM LAN 29-BIT VEHICLES 2006-UP
We recommend reading this installation guide first before starting any
INTERFACING SOLUTIONS
OVERVIEW OF INSTALLATION
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We offer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
CONNECT THE WIRES,
COLOR FOR COLOR.
MATCH LOOSEWIRES TO AFTERMARKET RADIO
SOOGM-16
front left speakers
front right speakers
rear left speakers
rear right speakers
constant
PARTS INCLUDED:
(1) Interface Module
(1) GM 29-Bit Harness (Part Number: Crux2513)
(1) Instruction Sheet
SOOGM-16A
Harness: 2606 Only.
accessory
ground
(1) Reverse Camera Harness (CJA2103A)
AFTERMARKET
RADIO
Covers 2012-UP Pick-Ups
w/ Navigation listed below.
illumination
amp on
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
vss
swc
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
BUICK:
2008 - 2012 Enclave
2006 - 2011 Lucerne
MUTE
PRELIMINARY:
CIRCUIT
Please read the entire mannual before installing this interface.
This unit provides the following:
8-PIN
CADILLAC
BOARD
(male plug)
2006 - 2010 DTS
2007 - 2013 Escalade
2007 - 2009 SRX
(SEE FIG 1)
- 12V Acc Output (3A Max/ RAP)
- Illumination Output (250mA Max)
- Low Voltage (Batt Run-Down Protection)
CHEVROLET:
2007 - 2013 Avalanche*
2007 - 2009 Equinox
2008 - 2011 Express Van
2006 - 2013 Impala/ Impala SS
2006 - 2007 Monte Carlo
2007 - 2013 Silverado* 1500-3500 Pickup
2007 - 2013 Suburban*
2007 - 2013 Tahoe*
Chimes Include:
- Seatbelt
- Check Engine
- Key In Ignition
- Low Fuel
16-PIN
(male plug)
24-PIN
12-PIN
INTERFACE
(male plug)
(male plug)
- Low Oil
- Lights On
14-PIN
Before installing this interface please review the options before
removing the factory radio. Some options may need to be adjusted
prior to removing the factory radio. Options include:
- Standard BOSE Amplifier
(male plug)
2009 - 2012 Traverse
THIS HARNESS ONLY HAS
TO FACTORY
HARNESS
GMC:
2007 - 2012 Acadia
2008 - 2011 Savana
2007 - 2013 Sierra 1500-3500 Pickup*
2007 - 2013 Yukon*
3-PINS POPULATED.
- Premium Bose (Y-91)
DO NOT PLUG IN THE
8-PIN
(male plug)
FULLY POPULATED 8-PIN.
IMPORTANT:
- The Front and Rear fading are not retained on Y-91 BOSE.
- The Onstar volume output is defaulted to low-gain
HUMMER:
2008 - 2009 H2
ADJUSTING THE GAIN
High Gain (Non-Bose Systems)
Press OnStar button, Heear “Onstar Ready“, Turn Dial knob to “9“,
Wait 4 seconds, Press Onstar button “Thank you Good Bye“.
Turn Dial knob back to Aftermarket radio corresponding.
USING THE MUTE CIRCUIT BOARD (FIG 1)
WIRING COLOR CODES
The external mute circuit is used to mute the audio on your radio.
Determine whether your radio is equipped with BOSE, then place
the 8 pin connector into the proper female connector. Reference the
PONTIAC:
2007 - 2009 Torrent
Black
Red
= Ground
= Accessory
= Constant
= Illumination
SATURN:
2007 - 2009 Outlook
2008 - 2009 Vue
Yellow
Orange
Blue/White
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Purple/White
Blue/Yellow
Orange/White
Yellow/Black
Red/White
sticker on the mute circuit board.
BOSE
The insterface is defaulted at Low-Gain.(BOSE Systems)
= Amplifier Turn-On
= Left Front (+)
= Left Front (-)
= Right Front (+)
= Right Front (-)
= Left Rear (+)
= Left Rear (-)
= Right Rear (+)
= Right Rear (-)
= Vehicle Speed Sense
= SWC (Kenwood/ JVC)
= Dimmer
REAR SEAT ENTERTAINMENT (SPECIAL ORDER)
1. Conect the rear seat entertainment 16-Pin connector to the vehicles
16-Pin factory connector.
2. Connect the RCA’s to the aftermarket radio video and audio input.
3. Test the video and audio before installing the radio into the dash.
8-PIN
(male plug)
SUZUKI:
2007 - 2008 XL7
Non-BOSE
*2012 Vehicles with Navigation Units are not
supported. Needed is SOOGM-16A
BACK-UP CAMERA CONNECTION
1. Conect the back-up camera 16-Pin connector to the vehicles 16-Pin
factory connector.
2. Connect the yellow video RCA to the new aftermarket radio video input.
3. Test the video feed before installing the radio back into the dashboard.
GRAY
Connector
Tech Tip:
Make sure to wipe the 3.5mm plug
before inserting into the aftermarket radio
to avoid a bad connection.
Connect to
Ground
Must Special Order Harness: CJA2333A
= Parking Brake
= Reverse Gear
RADIO REMOTE SELECT:
0. Pioneer
1. Alpine
2. Clarion
3. Kenwood
4. JVC
5. Sony/Jensen/Dual
Use a small screw
driver to make
adjustments.
Part Number: CJA2103A
This Interface Supports:
- BOSE Amplifier
- Y-91 System
- Rear Seat Entertainment*
- Back-Up Camera
USING THE SWC WIRE ON NEW JVC UNITS
New JVC units no longer carry the 3.5mm cable and have added the
SWC signal via a Lt. Blue/Yellow wire.
This wire needs to be connected to the SWC wire labeled “Kenwood”
also Lt. Blue/Yellow. Be sure to keep the dial switch set to number 4
when using JVC units.
The module has been rated for upto 3A max of output.
For applications demanding a continuous output of 3A or more,
we reccomend using a standard BOSCH (SPDT) relay.
See your local car audio specialist.
Note: Seek Up is not
supported on Jensen
radios.
|