JENN-AIR® DETAILED PLANNING DIMENSIONS
1 of 4
30" cOMbINATION MIcROwAvE/wALL OvENS
JMW3430W, JMW2430W, JMW2330W – 293⁄4" x 431⁄8" x 263⁄4"
PRODUcT DIMENSIONS
JMW3430W
JMW2430W
JMW2330W
MODEL #
A
in
cm
B C
Overall width
Pro-Style Stainless, Euro-Style Stainless
or Oiled Bronze
®
293⁄4
75.6
A
D
Floating Glass
295⁄8
6
75.3
15.2
0.9
E
F
Height of control panel
B
C
Space between control panel and door
Height to top of microwave oven handle
3⁄8
J
®
Pro-Style Stainless
111⁄4
11
125⁄8
28.7
28.0
31.9
2.4
D
Euro-Style (color-coordinating)
Height of microwave oven door
Space between doors
G
E
F
H
1
I
Height to top of oven handle
Pro-Style Stainless
®
201⁄4
20
215⁄8
11⁄2
51.4
50.7
54.9
4.0
G
Euro-Style (color-coordinating)
Height of oven door
Height of trim
FRONT VIEW
H
I
Overall height
431⁄8 109.4
J
Width of recessed oven
Width of conduit channel
Depth of recessed oven
Depth with doors
281⁄4
35⁄8
71.8
9.3
K
L
A
K
237⁄8
243⁄4
60.5
62.8
L
L
M
N
Depth with handles
Pro-Style Stainless
®
271⁄4
263⁄4
453⁄8 115.2
69.2
68.0
O
p
M
Euro-Style (color-coordinating)
Depth with door fully open
N
O
P
TOp VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120003A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
3 of 4
30" cOMbINATION MIcROwAvE/wALL OvENS
JMW3430W, JMW2430W, JMW2330W – 293⁄4" x 431⁄8" x 263⁄4"
OPENING/cLEARANcE DIMENSIONS
JMW3430W
JMW2430W
JMW2330W
A
MODEL #
in
30
281⁄2
cm
Width of cabinet (min.)
Width of cutout
76.2
A
B
C
72.4
Height of cutout
411⁄4 104.8
Top of cutout to bottom
of upper cabinet door (min.)
2
5.1
3.8
D
E
F
Bottom of cutout to top
of lower cabinet door (min.)
11⁄2
D
45⁄8-
11.7-
48.9
Bottom of cutout to floor
191⁄4
C
Depth of cutout (min.)
24
61.0
G
e
Recommended junction box location
B
ELECTRICAL REQUIREMENTS
240 volt, 40-amp fused, grounded circuit is required. A dedicated
circuit is recommended.
The length of conduit provided is for serviceability. Do not cut the
conduit. The junction box should be located 3" (7.6 cm) maximum
below the support surface. Drill a 11⁄4" (3.4 cm) minimum diameter
hole in the left rear corner of the support surface for access to the
junction box.
E
G
e
F
FRONT VIEW
SIDE VIEW
Power Supply Location
BACK VIEW
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120003A 07/2012
JENN-AIR® DETAILED PLANNING DIMENSIONS
4 of 4
30" cOMbINATION MIcROwAvE/wALL OvENS – FLUSh INSTALLATION
JMW3430W, JMW2430W, JMW2330W – 293⁄4" x 431⁄8" x 243⁄4" (depth without handles)
OPENING/cLEARANcE DIMENSIONS
JMW3430W
JMW2430W
JMW2330W
MODEL #
in
30
281⁄2
cm
Width of flush inset cutout (min.)
Width of opening (min.)
76.2
A
B
C
D
72.4
Height of flush inset cutout (min.) 4413⁄16 113.8
Height of opening (min.)
411⁄4 104.8
45⁄8-
11.7-
48.9
Bottom of cutout to floor
E
191⁄4
21⁄16" (5.2 cm)
Top Cleat*
Depth of cutout (min.)
25
63.5
F
e
Recommended junction box location
A
ELECTRICAL REQUIREMENTS
240 volt, 40-amp fused, grounded circuit is required. A dedicated
circuit is recommended.
B
C
The length of conduit provided is for serviceability. Do not cut the
conduit. The junction box should be located 3" (7.6 cm) maximum
below the support surface. Drill a 11⁄4" (3.4 cm) minimum diameter
hole in the left rear corner of the support surface for access to the
junction box.
D
3
3
⁄
4" (1.9 cm)
Side Cleat*
⁄
4" (1.9 cm)
Side Cleat*
FLUSH INSTALLATION REQUIREMENTS
A 25" (63.5 cm) minimum cutout depth is required.
11⁄2" (3.8 cm)
Platform*
These dimensions will result in a 3⁄8" (1.0 cm) reveal on the top,
a 1⁄8" (0.3 cm) reveal on the sides and a 13⁄8" (3.5 cm) reveal on the
bottom of the wall oven.
F
e
The front face of the cleats and platform will be visible and should
be treated as a finished surface.
E
FRONT VIEW
SIDE VIEW
Power Supply Location
F
Side Cleat*
1" (2.5 cm)
Side Cleat*
BACK VIEW
TOp VIEW
*Cleats and platform must be recessed 1" (2.5 cm) from the front of the cabinet.
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JRC120003A 07/2012
|