Jasco Headphones 86707 User Manual

To cancel pairing mode - While the headset is in pairing  
mode, you can cancel the pairing process and turn off  
the headset. Press and hold the Talk button for about 5  
seconds. You will hear an “OFF” tone, the Amber LED will  
flash several times and the headset will turn off. Release  
the Talk button.  
ADJUSTING THE VOLUME  
To increase the volume - While on a call, press and release  
(click) the Volume UP button “+” to increase volume by 1  
step. Repeat this procedure until you have reached the  
desired level. To decrease the volume - While on a call,  
press and release (click) the Volume DOWN button “-“ to  
decrease volume by 1 step. Repeat this procedure until you  
have reached the desired level.  
Bluetooth® Headset  
Tips:  
GE Model 86707  
* The headset, in normal operation, should maintain a  
link with the mobile phone at all times once pairing has  
been successful and a connection has been established  
between the two devices.  
You can also press and hold the volume buttons for  
automatic, step by step adjustment.  
User Guide  
Declaration of Conformity.  
We declare that product NHSTH4C2XXX  
conforms to the R&TTE Directive 1999/5/EC  
MUTING THE HEADSET  
* If you find that you cannot put the headset into pairing  
mode then try temporarily switching off (or disabling  
Bluetooth) the last phone used with the headset.  
You can mute and un-mute the microphone temporarily so  
that you cannot be heard by the connected party.  
To mute the headset – While on a call, press and hold  
the Talk button until you hear the MUTE tone (two rising  
scales), the microphone is muted. The headset will beep  
periodically to remind you that it is muted. To un-mute the  
headset - When the microphone is muted click either of  
the Volume buttons to activate the microphone again.  
TNZNHSTH4C2XXX  
* If disconnection or a lost link occurs, it may be due to the  
following reasons:  
a) The range is over 33 feet between the headset and the  
mobile phone.  
Charging Socket  
Blue LED  
b) The mobile phone disconnected the link to conserve  
power or enable another function.  
VISUAL INDICATORS  
Talk Button  
c) Either device has been switched off.  
Visual Indicators - 2 LEDs (blue and amber) indicate the  
status of the headset:  
FITTING THE HEADSET ON YOUR EAR  
Amber LED  
Volume UP+  
Status  
Indication  
The Headset is designed to fit comfortably in your ear. The  
ear hook can be fixed into the headset from both sides,  
allowing you to position on right or left ear. The ear hook  
can be separated from the Headset by simply pulling the  
base of the ear hook away from the main body of the  
Headset. The ear hook can then be reinserted in the other  
direction for positioning on the opposite ear. The ear hook  
is flexible and can be bent to adjust the fit that is best for  
the individual user. To replace the ear cap - Stretch the  
rubber ear cap around the end of the speaker until secure.  
Battery full  
Battery low  
Headset off  
Amber LED is off or dim  
Amber LED fkashes instead of Blue LED  
All LEDs are off  
Volume  
DOWN –  
Headset in standby  
mode; ready to make  
or receive calls  
Blue LED flashes at 3 second intervals  
Headset in pairing mode Blue and amber LEDs flash alternately  
Ear Hook  
TROUBLE SHOOTING  
To place the headset on your ear - Place the headset  
speaker in your ear with the microphone angled towards  
your mouth. The headset should fit snugly in your ear.  
Please note that you should also be familiar with the  
operation of your mobile phone or other connecting  
Bluetooth device. Please read the user guide for your  
device carefully. For operation with a PC or laptop please  
note that these devices should also be Bluetooth enabled  
with appropriate third party software in order to enable  
correct operation.  
Microphone  
SWITCHING ON YOUR HEADSET  
GETTING STARTED  
To turn on the headset - With the headset turned off, press  
and hold the Talk button for several seconds until you  
hear the “ON” tone (four ascending “beeps”) or until you  
see the Blue LED start to flash. Release the Talk button.  
The headset will turn on and enter standby mode, ready  
to make and receive calls. After turning on the headset,  
the headset will try to connect to the last used phone  
automatically.  
Remove all components from the package. Items in the  
pack include: Bluetooth headset with Ear Hook, Ear Cap,  
User Guide and AC Charger. Please check the contents  
carefully and contact your local dealer immediately if there  
are any shortages.  
Symptom/Problem  
Solution  
When talk button is pressed,  
no LED indicator  
• Unit not charged  
• Consult authorized dealer  
GETTING TO KNOW YOUR HEADSET  
Headset will not enter  
pairing mode  
• Disable Bluetooth on the last  
phone that was connected to  
the headset or try switching  
that phone off  
See image above. Please note some models of headset will  
differ slightly in style, color and the functionality may vary  
according to their specifications.  
To turn off the headset - With the headset turned on, press  
and hold the Talk button for about 5 seconds. You will hear  
an “OFF” tone (four descending “beeps”) and the Amber  
LED will flash quickly several times and the headset will  
turn off. Release the Talk button.  
Headset powers on with  
blue LED flashing but no  
connection to mobile phone  
• Check unit is paired to phone.  
Check settings in phone.  
Headset default name is BTHS.  
• Check phone is switched on  
• Check handsfree settings for  
phone  
CHARGING YOUR HEADSET  
Before using the headset, you must charge it for at least  
two hours. When fully charged, the battery provides up  
to 8 hours of talk time and up to 150 hours of standby  
time. Please note that talk time is also a function of the  
mobile phone and factory determined settings of the  
phone, so you may find this figure is reduced under certain  
conditions. To charge the headset  
MAKING CALLS  
You can make calls from your mobile phone, or directly  
from the headset using voice dialing and last number  
redial commands (if these features are supported by your  
mobile phone).  
• Ensure headset & phone are  
within range  
Headset does not charge  
• Check mains charger adapter  
is connected to the headset  
securely and is switched on.  
• Consult authorized dealer  
To make calls from your mobile phone - Dial the call from  
your mobile phone. Dependent on your mobile phone  
settings the call is automatically connected to your  
headset.  
1. Plug the AC charger into the headset.  
2. Plug the AC charger into a wall outlet. When the headset  
is charging, the amber LED will light up.  
CUSTOMER SERVICE INFORMATION In addition to the  
troubleshooting table on this page you can email help at:  
[email protected] or call 800 654-8483.  
3. When charging has finished, the amber LED will turn off  
or be dim. Unplug the charger cable from both the wall  
outlet and also from the headset.  
To make calls using VOICE DIALING (if supported by your  
mobile phone) - Click the Talk button on your headset. You  
will hear a Voice Dial tone possibly followed by the voice-  
dial prompt tone from your mobile phone. Speak the name  
of the person you wish to call. The call is automatically  
connected to your headset.  
For other Bluetooth products or support, please view our  
Battery Indication: The amber LED can turn off after less  
than 2 hours charging; this normally indicates that the  
headset can be used. However, for the initial charge, it is  
recommended that you charge the headset for at least  
2 hours in order to fully prepare the battery for normal  
operation.  
90 Day Limited Warranty  
Jasco Products Company warrants this product to be  
free from manufacturing defects for a period of ninety  
days from the original date of consumer purchase. This  
warranty is limited to the repair or replacement of the  
product only and does not extend to consequential or  
incidental damage to other products that may be used  
with this unit. This warranty is in lieu of all other warranties  
express or implied. Some states do not allow limitations on  
how long an implied warranty lasts or permit the exclusion  
or limitation of incidental or consequential damages, so  
the above limitations may not apply to you. This warranty  
gives you specific rights, and you may also have other  
rights which vary from state to state. If unit should prove  
defective within the warranty period, return prepaid with  
dated proof of purchase to: Jasco Products Company,  
311 N.W. 122nd St., Oklahoma City, OK 73114  
To make calls using LAST NUMBER REDIAL (if supported  
by your mobile phone) - While in standby mode, press and  
hold the Volume DOWN “-” or Volume UP “+” button for  
about 2 seconds, and you will hear a “Last Number Redial”  
tone (four ascending beeps); Release the Volume button,  
the call is automatically connected to your mobile phone.  
(You can also double-click the Talk button to activate this  
feature)  
PAIRING THE HEADSET WITH YOUR MOBILE PHONE  
Pairing is the process of linking the headset with your  
Bluetooth mobile phone. Before you use the headset with  
your mobile phone you must pair the devices.  
Please refer to your phone’s user manual for further  
information on ‘How to Pair’. Typically, you need to make  
your phone ‘Discover’ the headset by using a “Bluetooth”,  
“Connect” or “Setup” menu then selecting an option to  
“Discover” your headset.  
RECEIVING CALLS  
You must configure your mobile phone to answer calls  
directly on your Bluetooth headset. Refer to the mobile  
phone user guide for instructions on initiating this feature.  
To pair your headset and mobile phone  
When you hear your headset ring, click the Talk button on  
the headset. The call is automatically connected to your  
headset.  
1. Before you pair the headset, ensure that the battery is  
fully charged. If the headset battery is low then the amber  
LED will flash.  
ENVIRONMENT  
Reject calls (if supported by your mobile phone) You can  
also reject calls by pressing and holding the Talk button  
for about 3 seconds. You will hear a beep in addition to the  
incoming ringing when the call reject is about to occur.  
Do not throw this electrical device away with the normal  
household waste at the end of its life, but hand it in at an  
official collection point for recycling. By doing this you will  
help to preserve the environment.  
2. If you want to pair your headset with a second mobile  
phone then switch off the phone you last paired with.  
3. With the headset turned off, press and hold the Talk  
button for about 10 seconds until both the blue and amber  
LEDs flash alternately or until you will hear the “ON” tone  
followed by the “PAIR” tone (low/high beep).  
ENDING CALLS  
DISCLAIMER  
When you have finished your call, click the Talk button on  
your headset or end the call on your phone. The call will be  
disconnected.  
While every effort has been made to ensure that the  
information in this manual is accurate and complete, no  
liability will be accepted for any errors and/or omissions  
made. The manufacturer reserves the right to make  
changes and improvements to the specifications and  
features of the hardware and firmware of the products  
described in this document without prior notice.  
Reproduction, transfer, distribution or storage of part  
or all of the contents in this document in any form is  
prohibited without prior permission of the manufacturer.  
All trademarks acknowledged. The product is Bluetooth  
qualified by Nolan Systems.  
4. Release the Talk button. The headset is now in Pairing Mode.  
TRANSFERRING CALLS (if supported by your mobile  
phone)  
5. Initiate the device discovery feature on the mobile  
phone. After a few seconds your phone will display the  
headset’s Bluetooth name “BTHS”. (Refer to the mobile  
phone user guide for instructions for initiating this feature).  
You can transfer calls connected to your headset back  
to your mobile phone, or from your mobile phone to your  
headset.  
6. When prompted by the mobile phone, enter the headset  
pin code which is 0000. When pairing is complete, the blue  
LED on the headset will flash at three-second intervals and  
the headset will be placed in standby mode, ready to make  
and receive calls.  
To transfer calls from your headset to the phone double-  
click the Talk button. To transfer from phone to headset  
simply click the Talk button once.  
86707-3 vers. 2 9/06  
 

Ingersoll Rand Water Pump PH30F XXX XXX C User Manual
Intel Computer Hardware AR B1760 User Manual
Jet Tools Automobile Parts JSJ 3XA User Manual
John Deere Snow Blower ST0927 User Manual
JVC Camcorder LYT2046 001B M User Manual
JVC Digital Camera GZ MC200 User Manual
JVC VCR BR HD50E User Manual
JVC VCR HR A54U User Manual
Kenmore Range 3626278 User Manual
Kodak DVD Player MDV434K User Manual