LYT0002-0L8A
INSTRUCTIONS
English
ATTENTION:
Please note that the switch noise will be recorded if you
change the stereo angle while recording.
STEREO MICROPHONE
CU-V10U
PRECAUTIONS AND NOTES:
● The characteristics of the microphone will change if it is
dropped or subjected to shock or excessive force from
hitting it.
● During operation tests, please do not blow on the
microphone or hit it. Just talk normally into the
microphone.
● Precise parts are carefully arranged inside the microphone
for optimum use, but these characteristics can not be
retained if it is opened and disassembled. Please consult
your nearest JVC dealer or contact a service center for
repairs or maintenance.
● Please do not leave it near a heat source such as a stove,
direct sunlight, or in a car with all windows closed where
the temperature gets extremely hot. Direct exposure to a
camera light will damage the microphone, causing its
color to change and its body to deform.
Thank you for purchasing this stereo microphone. Before
use, please read this instruction manual carefully to ensure
proper use of this product, and keep this manual handy for
future use.
GENERAL BATTERY CAUTIONS:
● When the battery is misused, there is a danger that it may
leak or explode.
● Avoid using the microphone in places where it is
extremely humid, such as in a bathroom, or in areas
subject to oily smoke and vapor, such as near a range, as
this will cause it to malfunction.
Please read the following cautions regarding proper use.
1. Insert the battery with its positive + and negative – poles
positioned correctly as indicated.
2. Do not heat, disassemble, or throw it into a fire or short-
circuit the terminals.
Please carefully read the instructions printed on the
batteries.
INFORMATION
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
SPECIFICATIONS
Format
: Electret condenser type
: MS stereo with angle variation from
0° – 120° (with a 90° click-stop)
: – 45 dB (0 dB=1 V/Pa, at 1 kHz)
: 100 –16,000 Hz
Directivity
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Change or modifications not approved by the party
responsible for compliance could void the user’s authority to
operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Sensitivity
Frequency
Output impedance
Maximum input sound
pressure
: 600 ¸ ±30%
: 100 dB S.P.L or more
: 63 dB or more
Operating temperature : 0°C – 40°C
S/N ratio
Power
Power consumption
: DC 1.5 V ("AAA"/UM-4 battery)
: Less than 1 mA (when a UM-4 is
used.)
Battery duration
Output cord
: Approx. 300 hours of continuous
use (UM-4 at room temperature)
: 20 cm with a gold-plated stereo
mini-plug
: 3.6 (W) x 4.7 (H) x 12.9 (L) cm
: 75 g (not including the battery)
: "AAA" battery (UM-4 for function
tests)............................................. 1
Dimensions
Weight
Provided Accessories
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
E. & O. E. Design and specifications subject to change without notice.
Consult the dealer or an experienced radio/TV technician
for help.
|