SB-SC-XB/10W3v3-4 INSTR_SKU# 011277
InstallatIon
d I F F I C u lt Y :
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
out
oF
I n s t a l l a t I o n G u I d e
for the
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
15
SB-SC-XB/12W3v3-4
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
estImated tIme:
1 HouR
sKu#011277
2000
s t e P
1
Remove anything stored in the passenger rear corner of
the trunk so that you are working in a clean environment.
unpack the stealthbox® and test for proper operation
before continuing!
The wiring for the Stealthbox® should go from the seam
between the seatback and the floor to the amplifier location.
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
s t e P
2
Place the wax square as shown onto the interior panel.
Remove the two cargo anchors from the mounts as
indicated by the arrows. These anchors will be installed on
the Stealthbox.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
s t e P
3
Locate the threaded insert for the the mounting bolt, thread
the 3/8-16 bolt in so that only approximately 1/2” remains
out (see Detailed picture on next page).
Continued on Next Page
SB-SC-XB/10W3v3-4 INSTR_SKU# 011277
I n C l u d e d H a R d W a R e
(2) 1/4-20 X 1" Chrome Hex Head Bolt
(2) 6mm Flat Washer
(1) 3/8”-16 X 1 1/4" Hex Head Bolt
(1) 3/8” X 1 1/4" Flat Washer
(1) 3/8" Split Lock Washer
(1) 1" Aluminium Spacer
(1) 3”x 3” Wax Square
s P e C I F I C a t I o n s
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3-4
Nominal Impedance: 4 ohms
Continuous Power Handling: 500 watts RMS
P o W e R R e C o m m e n d a t I o n
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox®.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
m I d / H I G H F R e q u e n C Y d R I v e R F I t m e n t
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6 1/2””- Front Doors
Fits JL Audio Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi, C5-650, C
Rear Speaker Size / Location: 6 1/2”- Rear Door
Fits JL Audio Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi,
C5-650, C5-650x & ZR650-CSi
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011277 09-16-2008
•
Printed in USA
•
©2008 JL Audio, Inc. U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
•
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
1
0
3
6
9
N
O
R
T
H
C
O
M
M
E
R
C
E
P
A
R
K
W
A
Y
•
M
I
R
A
M
A
R
,
F
L
O
R
I
D
A
•
3
3
0
2
5
•
U
S
A
Page 3• JL Audio, Inc 2008
|