JBL Speaker AVR525 User Manual

PRO SOUND  
AVR580 QUICK-START GUIDE  
COMES HOME™  
®
Thank you for purchasing a JBL AVR580. This Quick-Start Guide will help  
you with a basic system installation. For detailed information on any step,  
please refer to the Owner’s Manual pages referenced in this guide. We  
strongly recommend that you read the Owner’s Manual for complete details  
on how to install, configure and operate the AVR580, as well as for the  
important safety information it contains.  
FRONT  
RIGHT  
SPEAKER  
CENTER  
SPEAKER  
(Green)  
FRONT  
LEFT  
SPEAKER  
(Red)  
FIGURE 1 – SPEAKER  
PLACEMENT  
The colors shown for each speaker correspond to  
the matching output terminal connection on the  
back of the AVR580 (see page 9).  
(White)  
SURROUND  
RIGHT  
SPEAKER  
(Gray)  
SUBWOOFER  
(Purple)  
CONNECTIONS COLOR  
GUIDE  
SURROUND  
LEFT  
SPEAKER  
Audio Connections  
Front  
Left  
Right  
SURROUND  
BACK  
Center  
RIGHT  
(Blue)  
Surround  
SPEAKER  
(Tan)  
SURROUND  
BACK  
Subwoofer  
LEFT  
Surround Back  
Digital Audio Connections  
Coax  
SPEAKER  
(Brown)  
Optical  
Step 1. Place your speakers in the listening room  
(see page 20).  
Video Connections  
Composite  
S-Video  
Match the colored jacks on the AVR580 to the appropriate  
jacks on your source equipment or speakers. The colors are  
standardized, but not all equipment or connectors use them.  
SPEAKER PLACEMENT  
 
FM Antenna  
AM Antenna  
CD PLAYER  
Optical  
L
R
Coax  
COMP V2  
COMP V1  
REGION SELECTOR  
AUDIO RECORDER  
FIGURE 4 – AUDIO CONNECTIONS  
Dashed lines (– – – –) indicate coax and optical digital audio con-  
nections. Choose either type (but not both) for each digital audio  
source.  
REC/IN  
PLAY/OUT  
Step 4. Connect AM and FM antennas (Fig. 4) (see page 17).  
Step 6. Region Selection: Set the Region Selector to “K” for South Korea.  
Set it to “C” for China or Hong Kong. Set it to “S” for Singapore,  
Malaysia, Indonesia or Thailand. (For other countries, please consult  
your local JBL distributor.) The Main Power Switch (not just Standby)  
must be turned off, then on again, in order for this selection to take  
effect (see page 35).  
Step 10. Configure speakers: No action is needed if you have five “small”  
satellite-type speakers and a subwoofer. Otherwise, press the  
Speaker button and then the Set and arrow buttons to select the cor-  
rect speaker choices for your system (see pages 24–26).  
Step 5. Connect source components, as shown in Figures 4 and 5, and in  
the Device Connection Options chart on the back of this guide (see  
pages 1718).  
AUDIO connections: Right channel (red) on source to right (red)  
on AVR, and left channel (white) on source to left (white) on AVR.  
DIGITAL AUDIO connections, if available: Choose either coax  
(orange) to coax (orange) OR optical to optical for each device.  
The Coax 1 input defaults to the DVD player, but may be reassigned.  
Assign the other digital inputs and outputs as appropriate for your  
equipment (see Step 8).  
VIDEO connections: Choose component (Y/Pb/Pr – green/blue/  
red), composite (yellow) or S-Video (4-pin) for each video source.  
The devices connected to the Component Video 1 and 2 inputs must  
be used with the DVD and Video 2 sources respectively. Connect the  
component, composite and S-Video Monitor outputs to your Video  
Monitor (TV). Switch your TV set’s input to match the type of video  
used for the currently selected source.  
Step 11. Use EzSet to set output levels: Set the Balance to 12 o’clock,  
and the Volume to 10dB. Sit in the listening position and hold the  
remote in front of you at shoulder level, pointing at the AVR580.  
Press the SPL button for 3 seconds, and release it when the LED  
flashes amber. Press “5” or “7” to indicate the number of speakers.  
Hold the remote steady until the process is completed (see  
pages 27–29).  
Step 7. Depending on the electrical requirements in your area, you may need  
to contact your JBL dealer to obtain the correct power cord. Plug all  
components into AC power outlets.  
Basic Receiver Configuration  
Step 8. Select digital inputs: If your DVD is connected to Coax 1, no adjust-  
ment is needed. For any other digital-device connections, use the  
front-panel Digital Select button and the arrow buttons to select an  
optical or coax digital input (see pages 22 and 32).  
Step 12. Your system is configured – sit back and enjoy!  
Step 9. Select a surround mode: Press the Surround Mode button on the  
front panel to select Dolby® Pro Logic® II – Movie. (You may select  
other modes later as you become familiar with the AVR580; see  
pages 22–24 and 31–35.)  
SPEAKER AND AUDIO CONNECTIONS  
 
VCR (Video 1)  
R
TV or Video Monitor (Video 3)  
S-Video Component Video  
Cable or Sat or HDTV Set-Top Box (Video 2)  
Out  
L
Video  
Video  
Component Video  
L
R
Video  
S-Video  
Y
Pb  
Pr  
Y
Pb  
Pr  
In/Rec  
In  
Out/Play  
Out  
Optical  
Coax  
L
R
COMP V2  
COMP V1  
REGION SELECTOR  
Component Video  
Y
FIGURE 5 – VIDEO CONNECTIONS  
Dashed lines (– – – –) indicate coax and optical digital audio connections. Choose either type (but not both) for each  
L
R
Video  
S-Video  
digital audio source.  
Pb  
Pr  
Dotted lines (••••) indicate component, composite or S-Video connections. Component video is the preferred connection  
when available, but you may use any of the three types (but not more than one). When component, composite and  
S-Video sources are connected to the AVR you must also connect all outputs from the AVR to your TV.  
Optical  
Coax  
DVD PLAYER  
Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4, Coax 3 and Optical 3 inputs are on the front panel of the receiver.  
Device  
CD Player  
DVD Player  
VCR  
Input Name  
CD  
Audio Input Connections  
Audio Output Connections  
Not required  
Video Connections  
Not required  
CD L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2  
Coaxial Digital 1 or 2, Optical Digital 1 or 2, or DVD L/R Inputs  
Video 1 L/R Inputs  
DVD  
Not required  
Component, Video 2, DVD Composite or S-Video  
Video 1 Composite or S-Video Input and Output  
Component Video 2, Video 2 Composite or S-Video Input  
Not required  
Video 1  
Video 1 L/R Outputs  
Cable Box or Satellite Receiver Video 2  
Video 2 L/R Inputs, Optical Digital 3  
*, or Coaxial Digital 3  
*
Inputs  
Not required  
Audio Recorder  
TV or Projector  
Tape  
Tape L/R Inputs, Optical Digital 1/2** or Coaxial Digital 1/2** Inputs  
Video 3 L/R Inputs  
Tape L/R Outputs, Digital Optical** or Coaxial Outputs**  
Not required  
Video 3  
Monitor-Out Component, Composite and/or S-Video  
Check with your cable service provider to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not. Digital audio recorders only.  
*
**  
PRO SOUND  
COMES HOME™  
VIDEO CONNECTIONS  
®
 

Ingersoll Rand Heat Pump 670079 User Manual
Intel Computer Hardware 8S661FXM RZ User Manual
Iomega Portable Media Storage 34729 User Manual
Jabra Headphones BT2080 User Manual
JVC DVD VCR Combo HR XVC29SU User Manual
JVC MP3 Docking Station 0397MKVUNSN User Manual
JVC Speaker System FS SD770 User Manual
JVC Stereo System CA NXF30 User Manual
Kenwood Speaker KFC W2510 User Manual
KitchenAid Mixer 6397dZw608 User Manual