NECK SUPPORT
Assembly, Installation, and Operating Instructions
SAFETY SUMMARY
Center Panel (STEP 3)
WARNING
DO NOT insta ll this e quipme nt without first re a d-
ing a nd understa nding this instruction sheet. If you
a re una ble to understa nd the se instructions, con-
ta c t a he a lthc a re profe ssiona l, de a le r, te c hnic a l
pe rsonne l if a pplic a ble be fore a tte mpting to in-
sta ll this e quipme nt - othe rwise , injury or da ma ge
ma y oc c ur.
Mounting
Screws
EP 4)
Curved Back
Neck Support Bra
ATTACHING THE NECK SUPPORT
(FIGURES 1 AND 2 )
Neck Support Assembly (STEP 8)
Thumbscrew
Knob (STEP 7)
Cu rved Back
1. Remove neck support bracket from packaging.
2. Unzip back cover on both sides of center panel.
3. Lift center panel.
Horizontal
Post (STEP 7)
NOTE: If a NEW neck support is used on an EXISTING
Curved Back than the adapter plate and support bracket
MUST be used.
Curved Back
Vertica
NOTE: If a NEW neck support is used on a NEW Curved
Back than the support bracket can be used WITHOUT
the adapter plate.
(STEP
Thumbscrew
Knob (STEP 9)
4. Perform Steps 4a. and 4b. or 4c.:
a. Secure neck adapter plate to the back shell
with the four (4) mounting screws provided (If
applicable).
Neck Support Bracket (STEP 8)
b. Then secure the neck support bracket to the
neck adapter plate using the two (2) mounting
screws provided.
c. Secure the vertical neck post to the back shell
using the two (2) mounting screws provided.
NOTE: Ensure that the retaining screw is located
in the end of the horizontal post.
Thumbscrew Knob
Depth
Adjustment
Retaining
Screw
5. Close center panel with the vertical neck post ex-
posed through the slot provided in upholstery.
6. Zip the back cover closed.
7. Insert horizontal post into vertical post and secure
with thumbscrew knob.
Height
Adjustment
Stop
Height
Horizontal Post
Vertical Post
8. Insert vertical post into neck support bracket.
9. Secure with a thumbscrew knob or adjustable lever.
Adjustment
Neck Support
Bracket
10. Insert detent pin into through both walls of vertical
post (Transport Ready Option [TRRO]).
Adjustment Lever
Detent Pin
11. If adjustment is required, refer to ADJUSTING THE
NECK SUPPORT in this instruction sheet.
NOTE: Neck Adapter Plate NOT shown.
FIGURE 1 - ATTACHING THE NECK SUPPORT
ON THE CURVED BACK
1
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE
TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This wa rra nty is e xte nde d only to the origina l purc ha se r/use r of our produc ts.
This wa rra nty give s you spe c ific le ga l rights a nd you ma y a lso ha ve othe r le ga l rights whic h va ry from
sta te to sta te .
Inva c a re wa rra nts its p rod uc t to b e fre e from d e fe c ts in m a te ria ls a nd workm a nship for the
pe riod of two (2) ye a rs on the Ne c k Support a nd 90 da ys on the c ove r from da te of purc ha se . If within
suc h wa rra nty pe riod a ny suc h produc t sha ll be prove n to be de fe c tive , suc h produc t sha ll be re -
pa ire d or re pla c e d, a t Inva c a re 's option. This wa rra nty doe s not inc lude a ny la bor or shipping c ha rge s
inc urre d in re pla c e me nt pa rt insta lla tion or re pa ir of a ny suc h produc t. Inva c a re 's sole obliga tion a nd
your e xc lusive re me dy unde r this wa rra nty sha ll be limite d to suc h re pa ir a nd/or re pla c e me nt.
For wa rra nty se rvic e , ple a se c onta c t the de a le r from whom you purc ha se d your Inva c a re
produc t. In the e ve nt you do not re c e ive sa tisfa c tory wa rra nty se rvic e , ple a se write dire c tly to
Inva c a re a t the a ddre ss on the ne xt pa ge . Provide de a le r's na me , a ddre ss, mode l numbe r, da te of
p urc ha se , ind ic a te na ture of the d e fe c t a nd , if the p rod uc t is se ria lize d , ind ic a te the se ria l
numbe r.
Inva c a re Corpora tion will issue a re turn a uthoriza tion. The de fe c tive unit or pa rts must be re turne d for
wa rra nty inspe c tion using the se ria l numbe r, whe n a pplic a ble , a s ide ntific a tion within thirty (30) da ys of
re turn a uthoriza tion da te . DO NOT re turn produc ts to our fa c tory without our prior c onse nt. C.O.D.
shipme nts will be re fuse d; ple a se pre pa y shipping c ha rge s.
LIMITATIONS AND EXCLUSIONS: THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NOR-
MAL WEAR OR FAILURE TO ADHERE TO THE ENCLOSED INSTRUCTIONS. IN ADDITION, THE FOREGOING
WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN RE-
MOVED OR DEFACED; PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAIN-
TENANCE OR STORAGE; OR PRODUCTS MODIFIED WITHOUT INVACARE'S EXPRESS WRITTEN CONSENT
INCLUDING, BUT NOT LIMITED TO: MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR AT-
TACHMENTS: PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE
SPECIFIC CONSENT OF INVACARE; PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND INVACARE'S
CONTROL; PRODUCTS REPAIRED BY ANYONE OTHER THAN ANAUTHORIZED INVACARE DEALER, SUCH
EVALUATION SHALL BE SOLELY DETERMINED BY INVACARE.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, IF ANY,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
IT SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY PROVIDED HEREIN AND THE
REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT
OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. INVACARE SHALL NOT BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/ PROVINCIAL LAWS AND
REQUIREMENTS.
3
INVA
C
A
R
E
C
O
R
P
O
R
A
T
I
O
N
l
O
N
E
INVA
C
A
R
E
W
A
Y
l
P
.
O
.
B
o
x
4
0
2
8
l
E
l
y
r
i
a
,
O
h
i
o
4
4
0
3
6
-
2
1
2
5
l
Phone 1-(800)-333-6900
INVACARE CANADA l 5970 Che d worth Wa y l Mississa ug a , Onta rio Ca na d a L5R 3T9 l
Phone (905) 890-8300, 1-800-668-5324, Fa x (905)-890-5244
Form No. 96-326
Pa rt No. 1068859
Re v. C (1) - 7/ 99
Printe d in U.S.A.
|