(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
IMPORTANT
SAFETY RULES
Read, Understand, and Follow all
Instructions Carefully before
Installing and using this Product.
TM
Krystal Clear
Model 638 Filter Pump
220 - 240 V~, 50 Hz, 85 W
Hmax 1.0 m, H min 0.19 m, IPX7
Max. Water Temperature 35 °C
For illustrative purposes only.
Don’t forget to try these other fine Intex products: Pools, Pool Accessories,
Inflatable Pools and In-Home Toys, Airbeds and Boats available at fine
retailers or visit our website.
©2006 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., 8th Floor, Dah Sing
Financial Centre, 108 Gloucester Road, Wanchai, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach,
CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea
por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The
Netherlands
106**-A0-0701
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual current device
(PRCD).
• Do not bury electrical cord. Locate cord where it will not be damaged by lawn
mowers, hedge trimmers, and other equipment.
• The supply cord cannot be replaced. If the cord is damaged the appliance should
be scrapped.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Assembly and disassembly by adults only.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
• Position this product away from pool to prevent a child from climbing on pump to
access the pool.
• Children must stay away from this product and electrical cord(s).
• Do not operate this product when pool is occupied.
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• This product is for use with storable pools only. Do not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• Keep this product more than 2m away from the pool. (for France only).
• Keep the plug of this product more than 3.5m away from the pool.
• The plug shall be accessible after product installed.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
Page 3
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
PARTS LIST
1
4
7
2
5
8
3
6
9
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to
scale.
Page 4
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
1
2
3
4
6
5
7
8
9
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
DESCRIPTION
AIR RELEASE VALVE
REF. NO.
QTY.
SPARE PART NO.
10460
1
2
3
4
5
6
7
8
9
1
1
1
1
1
2
2
4
2
VALVE O-RING
THREADED COVER
COVER SEAL
10264
10459
10325
FILTER CARTRIDGE (59900)
STRAINER
10120
10399
10122
10134
HOSE
HOSE CLAMP
HOSE SEAL
When ordering parts, be sure to quote the model number and part numbers.
Page 5
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
SET-UP INSTRUCTIONS
Be sure you have access to water to fill the pool and chemicals for the water. A
small coin can be used to tighten the hose clamps (8).
IMPORTANT:This filter pump is shipped with the air release valve (1) open
(open the air release valve if necessary). DO NOT replace the air release valve
until you reach STEP #8. Failure to follow these instructions will result in air
trapped inside filter housing; the motor will run dry, be noisy and
malfunction.
1. Assemble above-ground-pool first. Carefully follow the pool’s installation
instructions.
2. Place the Filter-Pump the length of the hose away from the pool wall where the
lower black protruding hose connection is "sticking-out".
3. Remove wall plugs and then insert the strainers (6) into each of the protruding
hose connections. The hoses (7) fit over the strainers inserted into the
connections.
4. There are two hoses to be connected to the Filter-Pump hose connections.
With hose clamps (8), fasten one of the hoses (7) to the lower protruding hose
connection (marked "+" on the pool liner) and to the pump connection (marked
"+").
5. Connect the second hose to the remaining upper protruding hose connection
and to the lower pump connection. Make sure all the hose clamps (8) are tight.
6. Twist the Filter-Pump’s threaded cover (3) in a clock-wise direction to be sure it
is on "tight". Use only your hands to tighten the top. Do not tighten with tools
such as pliers.
7. Fill the pool to a level of at least 1-2 inches above the top connection. The
water will automatically flow down into the pump.
8. When water starts flowing out of the air release valve hole, screw in the air
release valve back into the filter housing cover. Do not over tighten the valve.
NOTE: Venting the system is necessary for air to escape as the filter
housing fills with water.
9. Connect the filter pump to the power outlet. The filter pump is now filtering the
water.
WARNING
Risk of electric shock. Connect this product only to a grounding
type receptacle protected by a ground-fault circuit interrupter
(GFCI) or residual current device (RCD). Contact a qualified
electrician if you cannot verify that the receptacle is protected by a
GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual
current device (PRCD).
10. Operate the filter pump until the desired water clarity is obtained.
Page 6
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
SET-UP INSTRUCTIONS (continued)
WARNING
Position this product away from pool to prevent a child from
climbing the pool.
To inspect and change the filter cartridge, disconnect line cord, unscrew the
strainer grids (6) from the strainer connectors and insert the hat-like plugs into the
strainer connectors before servicing the filter. After service, open the air release
valve, remove the plugs, allow any air to escape through the valve before tightening
the valve again and replace the strainer grids. The pump is now primed with water
again and may be turned on.
WATER LEVEL
UPPER PROTRUDING
HOSE CONNECTION
AIR RELEASE
VALVE
THREADED
COVER
PLUG
HOSE
STRAINER
FILTER
CARTRIDGE
INSIDE
UPPER PUMP
CONNECTION
INSIDE OF POOL
BOTTOM PUMP
CONNECTION
HOSE
CLAMP
(ILLUSTRATION NOT TO SCALE)
Page 7
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
FILTER PUMP STATIONARY MOUNTING OPTION
There are three mounting holes located at the bottom of the filter-pump base.
These holes are provided because various country’s regulations, especially in the
European community, require the filter-pump to be secured to the ground or to a
base in a permanent upright position.
These three holes form a triangle pattern and are 145mm from each other. The
holes are slotted with a 7mm width.
The filter-pump can be mounted on a cement base or onto a wooden structure to
prevent accidental falling over. Total assembly must exceed 18kg. The drawings on
the following show two possible ways of upright mounting. The European norm
EN 60335-2-41 requires this product be secured to the ground or to a base.
145mm
145mm
145mm
145mm
145mm
-- (3) x M6 HEXAGON LOCK-NUTS
-- (3) x M6 HEXAGON HEAD BOLTS
Page 8
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
FILTER CARTRIDGE CLEANING OR REPLACEMENT
It is recommended that the filter cartridge be replaced at least
every 2 weeks.
1. Make sure filter pump is not operating. Disconnect line cord.
2. To prevent water from escaping the pool, unscrew the strainer grids from the
strainer connectors and insert the hat-like plugs into the strainer connectors.
3. In a counter-clockwise motion, remove threaded cover (3) and cover seal (4).
Be careful not to lose the cover seal (4).
4. Remove filter cartridge (5) to clean it. The filter may be cleaned from the spray
from a water hose.
5. Use judgement as to whether cartridge needs to be replaced.
6. Return cartridge to filtering position.
7. Return the seal (4) and threaded cover (3) to their original positions. Tighten
the threaded cover (3) by hand only, twisting it in a clock-wise direction.
8. After service, open the air release valve, remove the plugs, allow any air to
escape through the valve before tightening the valve again and replace the
strainer grids. The pump is now primed with water again and may be turned on.
Page 9
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
POOL CARE AND CHEMICALS
•
All pools require care to keep the water clear and hygienically clean. With
proper chemical control, your filter will help attain this objective. Consult your
pool supply dealer for instructions regarding the proper use of chlorine,
algaecide and other chemical agents required for sparkling clear water.
Keep pool chemicals away from children.
•
•
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
•
Daily pH checking and chemical treatment of the water is very important and
can not be overemphasized. Chlorine, algaecide and maintenance of proper pH
levels are required when filling the pool as well as during the season. Consult
your local swimming pool supply store for instructions.
•
The season's first filling of the pool may have brackish water requiring extra
water additives and extra filter changes. Do not allow swimming in pool until the
pH level is balanced. Consult your local swimming pool supply store for
instructions.
•
•
Keep spare filter cartridges on hand. Replace cartridges every two weeks.
Chlorinated water may damage lawns, gardens or shrubbery as children play
in the pool and splash water outside the pool. Lawn areas underneath the
pool liner will be destroyed. Note that some types of grass may grow through
the liner but function is not affected.
•
Filter run time depends on pool size, weather and usage level. Experiment with
various run times so as to produce clean clear water.
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always
follow the chemical manufacturer’s directions, and the health and hazard
warnings.
LONG TERM STORAGE
1. Before emptying your pool for long term storage, or relocation, be sure the
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. After pool is empty of all water, disconnect all pool hoses (7) from pool and
filter pump, simply reverse the set up instructions.
3. Remove filter cartridge as shown in the Filter Cartridge Cleaning section,
steps 2 thru 4.
4. Remove the strainers (6) from the pool wall. Place the wall plugs into the hose
connections. Loosen clamps (8) securing the strainers before removal.
5. Drain water from the filter pump housing.
6. Depending on the cartridge (5) usage, a new cartridge may be needed for next
season, keep a spare available.
7. Cover the seal (4), air release valve O-ring (2) and hose seals (9) with
petroleum jelly to preserve its resilience during storage.
8. Store the filter pump and accessories in a dry, cool storage location.
9. The original packing carton can be used for storage.
Page 10
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
TROUBLESHOOTING GUIDE
TROUBLE
CHECK
POSSIBLE SOLUTIONS
FILTER MOTOR
FAILS TO START
• Not plugged in.
•
Filter cord must be plugged into a 3 wire
outlet that is protected by a Class A
Ground Fault Circuit Interrupter, or RCD.
• Fuse box needs checking.
• GFCI/RCD circuit breaker
tripped.
• Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Motor too hot and overload protection
shut motor off. Let motor cool down.
FILTER DOESN’T
CLEAN POOL
• Improper chlorine or pH
levels.
• Filter cartridge dirty.
• Cartridge damaged.
• Excessively dirty pool.
• Strainer screen restricting
flow.
•
Adjust chlorine and pH level. Consult
your local swimming pool supply stores.
• Clean or replace cartridge.
• Check for holes in cartridge. Replace
if damaged.
• Operate filter for longer periods.
• Clean strainer screen at pool wall inlet.
FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY
SLOW
• Inlet/discharge clogged.
• Air leak on intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Filter cartridge dirty.
• Look for obstructions in intake hose or
discharge hose inside pool wall.
• Tighten hose clamps, check hoses for
damage, check pool water level.
• Replace cartridge.
• Clean cartridge more often.
PUMP DOESN’T
WORK
• Low water level.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose clamps, check hose for
damage.
• Check & clear any sticks or leaves in
intake to pump.
• Strainer screen plugged up.
• Air leak on intake hose.
• Faulty motor or impeller
jammed.
• Air lock inside cartridge
chamber.
• Open release valve at top of pump.
TOP COVER
LEAKING
• O-ring missing.
• Cover not tight.
• Filter cartridge dirty.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
HOSE LEAKING
AIR LOCK
• Hose clamps.
• Tighten/change hose clamps.
• Pump housing and inlet hose
air trapped.
• Open air release valve, lift and lower
the inlet hose until water starts to flow
out of the air release valve, close air
release valve.
• The white inserts at both ends of the hoses shall remain inside and
shall be firmly inserted in the hose. Do not remove the white inserts
from the hoses. These white inserts are not serviceable parts.
• To facilitate the connection of the hoses into the black protruding hose
connectors on the pool wall, you may use soapy water solution (mix 6
drops of dish detergent in 1/2 a cup of water) to lubricate the inserts
by simply dipping the hose ends into the solution. Continue per
owner’s manual.
HOSE
INSERT
• Do not use lubricants such as machine or industrial oil or grease.
Page 11
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
COMMON POOL PROBLEMS
PROBLEM
DESCRIPTION
CAUSE
REMEDY
ALGAE
• Greenish water.
• Green or black
spots on pool liner.
• Pool liner is
• Chlorine and pH levels • Super chlorinate with shock
need adjustment.
treatment. Correct pH to your
pool store's recommended
level.
slippery and/or has
a bad odor.
• Vacuum pool bottom.
• Maintain proper chlorine
level.
COLORED
WATER
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Copper, iron or
maganese in water
being oxidized by the
added chlorine.
Common.
• Adjust pH to recommended
level.
• Run filter until water is clear.
• Clean cartridge frequently.
SUSPENDED
MATTER IN
WATER
• Water is cloudy or
milky.
• "Hard water" caused
by pH level being too
high.
• Chlorine content is low.
• Foreign matter in
water.
• Correct pH. Check with pool
dealer for water treatment.
• Check for proper chlorine
level.
• Clean or replace your filter.
CHRONIC
LOW WATER
LEVEL
• Level is lower than
on previous day.
• Rip or hole in pool
liner or hoses. Tighten
caps.
• Repair with patch kit.
• Finger tighten all caps.
SEDIMENT
ON POOL
BOTTOM
• Dirt or sand on
pool floor.
• Heavy use, getting in
and out of pool.
• Use Intex pool vacuum to
clean bottom of pool.
SURFACE
DEBRIS
• Leaves, insects
etc.
• Pool too close to
trees.
• Use Intex pool skimmer.
IMPORTANT
If you continue to experience difficulty, please contact our
Consumer Service Department for assistance. See back cover for
contact information.
Page 12
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all instances or risk and or danger.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is watching your children about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Teach children what to do in case of an emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, Supervise, Supervise.
Page 13
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
LIMITED WARRANTY
PARTS LIST
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal
Clear™ Filter-Pump.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for a period of one (1) year from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
If a manufacturing defect is found within this one (1) year period, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will determine
the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN
NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE
TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL
DAMAGES OR LIABILITIES.
This Limited Warranty does not apply if the Krystal Clear™ Filter-Pump is subject to
negligence, abnormal use or operation, accident, improper operation, improper voltage or
current contrary to operating instructions, or to damage by circumstances beyond Intex’s
control, including but not limited to, ordinary wear and tear and damage caused by
exposure to fire, flood, freezing, rain, or other external environmental forces. This Limited
Warranty applies only to those parts and components sold by Intex. The Limited Warranty
does not cover unauthorized alterations, repairs or disassembly by anyone other than Intex
Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.
Page 14
SAVE THESE INSTRUCTIONS
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007
106
For service questions or to order replacement parts, please contact the appropriate office
questions.
AREAS
LOCATION
AREAS
LOCATION
COMEXA S.A
SAN IGNACIO 0201, PARQUE
INDUSTRIAL PORTEZUELO,
QUILICURA, SANTIAGO, CHILE
TEL: 56-2-339 9000
•
CHILE / ARGENTINA /
PERU / URUGUAY
•
ASIA
INTEX DEVELOPMENT CO. LTD.
8TH FLOOR,
DAH SING FINANCIAL CENTRE,
108 GLOUCESTER ROAD,
WANCHAI, HONG KONG
TEL: 852-28270000
FAX: 56-2-339 9022
FAX: 852-23118200
E-mail: [email protected]
SAUDI ARABIAN MARKETING &
AGENCIES CO. LTD.
PRINCE AMIR MAJED STREET,
AL-SAFA DISTRICT. JEDDAH,
KINGDOM OF SAUDI ARABIA
TEL: 966-2-693 8496
E-mail: [email protected]
INTEX TRADING B.V.
POSTBUS 1075, 4700 BB ROOSENDAAL,
THE NETHERLANDS
TEL: 31-(0)165-593939
•
SAUDI ARABIA
•
•
•
•
EUROPE
FRANCE
GERMANY
ITALY
FAX: 31-(0)165-593969
FAX: 966-2-271 4084
E-mail: [email protected]
INTEX SERVICE (FRANCE) SAS
52, ROUTE NATIONALE
39190 BEAUFORT, FRANCE
TEL: 08 90 71 20 39 (0.15 TTC/min)
FAX: 03 84 25 18 09
E-mail: [email protected]
STEINBACH GMBH GERMANY
AN DER WELLE 4
60322 FRANKFURT
E-mail: [email protected]
STEINBACH GMBH AUSTRIA
AISTINGERSTRAßE 2
4311 SCHWERTBERG
TEL: 0800 468397665
FAX: 07262 61439-0
E-mail: [email protected]
INTEX TRADING S.R.O.
BENESOVSKA 23,
101 00 PRAHA 10
CZECH REPUBLIC
TEL: 420-2-717 32247
FAX: 420-2-673 12552
E-mail: [email protected]
N.V. NICOTOY S.A.
•
•
AUSTRIA
CZECH REPUBLIC /
EASTERN EUROPE
TEL: 0800 468397665
FAX: 07262 61439-0
E-mail: [email protected]
A & A MARKETING SERVICE
OFFICE: VIA DEI MESTIERI 8, 20049
CONCOREZZO, MILANO - ITALY
TEL: 39-039-6886260
•
•
BELGIUM
DENMARK
MOESKROENSESTEENWEG 383 C,
8511 AALBEKE
TEL: 0800 92088
FAX: 39-039-6043603
E-mail: [email protected]
WAREHOUSE: C/O ALVI, VIALE DELLA
REPUBBLICA 10 - 27100 PAVIA - ITALY
TOY BROKERS LTD
MARKETING HOUSE,
BLACKSTONE ROAD
HUNTINGDON, CAMBS.
PE29 6EF. UK
TEL: 01480 414361
FAX: 32-56.20.37.61
E-mail: [email protected]
K.E. MATHIASEN A/S
SINTRUPVEJ 12
DK-8220 BRABRAND
DENMARK
TEL: +45 89 44 22 00
FAX: +45 86 24 02 39
E-mail: [email protected]
LEKSAM AB
BRANDSVIGSGATAN 6,
S-262 73 ÄNGELHOLM,
SWEDEN
TEL: +46 431 44 41 20
FAX: +46 431 190 35
E-mail: [email protected]
NORSTAR AS
PINDSLEVEIEN 1
N-3221 SANDEFJORD
NORWAY
TEL: +47 33 48 74 10
•
•
•
UK
FAX: 01480 414761
•
•
•
•
SWEDEN
NORWAY
FINLAND
RUSSIA
E-mail: [email protected]
GWM AGENCY
GARTEN-U. WOHNMÖBEL
RÄFFELSTRASSE 25
POSTFACH
CH-8045 ZURICH/SWITZERLAND
TEL: + 41 - (0)900 - 455 456
FAX: 41 44 455 50 65
E-mail: [email protected]
KOKIDO BVI LIMITED
C/PLOMO 5-7, NAVE 19 POLÍGONO
INDUSTRIAL AIMAYR SAN MARTÍN DE
LA VEGA 28330 MADRID SPAIN
TEL: 34-90-2351045
SWITZERLAND
SPAIN / PORTUGAL
FAX: +47 33 48 74 11
E-mail: [email protected]
NORSTAR OY
RUUKINTIE 20
FIN-02330 ESPOO
FINLAND
TEL: +358 9 8190 530
FAX: +358 9 8190 5335
E-mail: [email protected]
LLC BAUER
KIEVSKAYA STR., 20,
121165 MOSCOW, RUSSIA
TEL: 095-249-9400/8626/9802
FAX: 095-742-8192
E-mail: [email protected]
KATHAY HASTER
UL. LUTYCKA 3,
60-415 POZNAN
TEL: +48 61 8498 381/380
FAX: +48 61 8474 487
E-mail: [email protected]
RECONTRA LTD.
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,
HUNGARY
FAX: 34-91-6912709
E-mail: [email protected]
E-mail: [email protected]
HUNTER OVERSEAS PTY LTD
LEVEL 1, 225 BAY STREET,
BRIGHTON, VICTORIA
AUSTRALIA
•
•
AUSTRALIA
TEL: 61-3-9596-2144 or 1800-224-094
FAX: 61-3-9596-2188
E-mail: [email protected]
HAKA NEW ZEALAND LIMITED
UNIT 5, SENTINEL PARK,
25 AIRBORNE ROAD, ALBANY
PO BOX 302171,
NORTH HARBOUR,
AUCKLAND 1330
NEW ZEALAND
TEL: 649-4159213
FAX: 649-4159212
E-mail: [email protected]
FIRST GROUP TRADING
AL MOOSA GROUP BUILDING, 1ST
FLOOR, OFFICE 102 & 103, UMM HURAIR
ROAD, KARAMA, DUBAI, UAE
TEL: 00971-4-3373322
NEW ZEALAND
•
•
•
POLAND
HUNGARY
BRAZIL
•
•
MIDDLE EAST
REGION
TEL: +361 372 5200/113
FAX: +361 209 2634
E-mail: [email protected]
KONESUL MARKETING & SALES LTDA
RUA INÁCIO BORBA, 835 - CEP. 04715-020,
CHÁCARA SANTO ANTONIO - SÃO
PAULO - SP - BRASIL
TEL: 55 (11) 5183 8866
FAX: 55 (11) 5183 8866
E-mail: [email protected]
FAX: 00971-4-3375115
E-mail: [email protected]
WOOD & HYDE
15-17 PACKER AVENUE, INDUSTRIA 2,
CAPE TOWN, SOUTH AFRICA 7460
TEL: 27-21-0800-204-692
FAX: 27-21-505-5600
SOUTH AFRICA
E-mail: [email protected]
Page 15
SAVE THESE INSTRUCTIONS
|