Intel®
NetStructure™ 6000
Switch
User Guide for the Gigabit and
Fast Ethernet Modules
Intel®
NetStructure™ 6000
Switch User Guide
for the Gigabit and
Fast Ethernet
Modules
ꢀ
A21721-001
Copyright © 2000, Intel Corporation. All rights reserved.
Intel Corporation, 5200 NE Elam Young Parkway, Hillsboro OR 97124-6497
Information in this document is provided in connection with Intel® products. No license, express or
implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except
as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatso-
ever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products
including liability or warranties relating to fitness for a particular purpose, merchantability, or infringe-
ment of any patent, copyright or other intellectual property right. Intel products are not intended for use
in medical, life saving, or life sustaining applications. Intel may make changes to specifications and
product descriptions at any time, without notice.
*Other product and corporate names may be trademarks of other companies and are used only for explanation and
to the owners’ benefit, without intent to infringe.
First Edition
May 2000
A21721-001
Contents
Chapter 1 Quick Start
5
Module Installation....................................................... 7
Chapter 2 Gigabit Ethernet Modules
9
Overview of the Gigabit Ethernet Modules ................ 10
1000Base-SX Module................................................ 10
1000Base-LX/1000Base-SX Module ......................... 12
Chapter 3 Fast Ethernet Modules
15
Overview of the Fast Ethernet Modules..................... 16
10/100 Ethernet Module............................................. 16
3
Quick Start
Topic
Module Installation
See Page
7
C H A P T E R 1
Intel® NetStructure™ 6000 Switch Modules User Guide
The Intel® NetStructure™ 6000 switch is a modular switch that sup-
ports up to four media modules. The table below describes the available
modules.
Available
Modules
per
Chassis
Available
Ports per
Chassis
Featuresper
Slot
I/O Modules
1000Base-SX
Switch Module
4
32
Eight-port
full-duplex
switched
Gigabit
Ethernet
module
1000Base-LX/
1000Base-SX
Switch Module
4
32
Eight-port
full-duplex
switched
Gigabit
Ethernet
module with
four LX and
four SX ports.
10/100Base-TX
Switch Module
4
96
100Base-TX
Ethernet
module
containing 24
switched RJ-
45 ports.
6
C H A P T E R 1
Quick Start
Available
Modules
per
Available
Ports per
Chassis
Featuresper
Slot
I/O Modules
Chassis
Control
Processor
2
N/A
Each contains
one RS-232
(DB9)
connector and
one RJ-45 10/
100 Ethernet
management
port.
Module Installation
Gigabit
Ethernet
Module
To install a module
1
Remove the module from the carton.
Warning Electrostatic Sensitive Device. Do not handle the printed
circuit board unless your work area is static-free!
7
C H A P T E R 1
Intel® NetStructure™ 6000 Switch Modules User Guide
2
3
4
Carefully remove the module from the ESD protective bag and
place it on a flat surface.
Remove the blank filler tray from any of the empty slot bays on the
switch.
Lift up the module by placing both hands on the side of the module
faceplate panel or underneath the card.
5
6
Carefully slide the module into the empty slot.
Push the module back until it connects with the backplane and the
capture panel screws engage the chassis.
7
Tighten both capture panel screws simultaneously.
8
Gigabit Ethernet
Modules
Topic
See Page
Overview of the Gigabit Ethernet Modules 10
1000Base-SX Module
10
12
1000Base-LX/1000Base-SX Module
C H A P T E R 2
Intel® NetStructure™ 6000 Switch Modules User Guide
Overview of the Gigabit
Ethernet Modules
The Intel® NetStructure™ 6000 switch has two Gigabit Ethernet
modules. One is a 1000Base-SX card and the other is a 1000Base-
LX/1000Base-SX card.
1000Base-SX Module
The chassis can house up to four 1000SX Gigabit Ethernet modules.
Each Gigabit Ethernet module has eight switched ports.
Each port operates in full-duplex mode only, and can be put in auto-
negotiation mode for flow control parameters.
Setting Auto-negotiation
Auto-negotiation makes it possible for devices to exchange
information about their abilities over a link segment. This function
allows the devices at both ends of a link segment to advertise abilities
and acknowledge receipt and understanding of the common modes of
operation that both devices share.
The default setting for the switch has auto-negotiation enabled on all
of the ports.
1
Type show link autoneg port_number to display the auto-nego-
tiation parameters for a link.
2
Type the privileged set link port_number noautoneg command
to disable auto-negotiation on a port.
The Gigabit Ethernet module supports full-duplex mode only.
Note If auto-negotiation is not enabled for a remote partner of a
6000 switch port and another Gigabit Ethernet device, auto-
negotiation must be disabled.
Only devices configured for full-duplex mode may send pause
frames. Pause frames provide flow control over full-duplex links.
10
C H A P T E R 2
Gigabit Ethernet Modules
Gigabit Ethernet Configuration
Link LED
1000SX
1000SX
1000SX
1000SX
1000SX
1000SX
1000SX
1000SX
RX LED
Status LED
TX LED
The Gigabit Ethernet module uses SC duplex connectors as defined
by the IEC 87-419 standards. The table below describes the
maximum cable length for the module.
Cable Type
Length
62.5 micron multimode
60 micron multimode
2 to 275 meters
2 to 550 meters
6.56 to 902.2 feet
6.56 to 1804.4 feet
Light Emitting Diodes (LEDs) provide status information for the
module. There are three LEDs per port (link, transmit and receive)
and one global LED (status).
The table describes the LEDs for the module.
LED
Color
Definition
Status (Board)
Solid Yellow
Power up diagnostics
are running.
Flashing Yellow
Flashing Green
Power up diagnostics
failed.
Normal Operation -
the board is operating
normally.
11
C H A P T E R 2
Intel® NetStructure™ 6000 Switch Modules User Guide
LED
Color
Definition
Link
Solid Green
The Link LED is
available on each
port. The Link LED
stays on while a good
link is available.
RX (Receive)
TX (Transmit)
Flashing Green
Flashing Green
The Receive LED is
available on each
port. It flashes on and
off as frames are
received.
The Transmit LED
flashes on and off as
frame transmissions
start and stop.
1000Base-LX/1000Base-SX
Module
LX ports
SX ports
Link LED
1000Base-LX
1000Base-SX
Port
1
Port
3
Port
4
Port
5
Port
6
Port
7
Port
8
Port
2
RX LED
Status LED
TX LED
The switch supports up to four SX/LX modules for a total of 32 Gigabit
Ethernet ports. In addition, each port can be enabled or disabled, and
can be configured to support auto-negotiation.
Configuring ports
The default setting has all ports enabled by default. Type show port
{ port_number | all } at the command line to view the port configuration
Before you can change port configuration, make sure that you are in
12
C H A P T E R 2
Gigabit Ethernet Modules
privileged mode. Refer to the Intel® NetStructure™ 6000 User Guide
for instructions on entering privileged mode.
You can configure any port as enabled (active and allowing data to
pass) or disabled (inactive with no data transmission or reception).
All ports are enabled by default.
To disable a port, type disable port port_number.
6000 Switch>#>disable port 8
The table below describes the maximum cable length for the module.
Port
Type
Cable Type
Length
1000SX
62.5 micron multimode 2 to 275 meters
6.5 to 902.2 feet
6.5 to 1,804.5 feet
16,404.2 feet
60 micron multimode
2 to 550 meters
5 kilometers
1000LX
single-mode fiber
between a 6000 switch
1000Base-LX port and a
1000Base-LX port on a
non-6000 switch port.
single-mode fiber
10 kilometers
32,808.4 feet
between two 6000 switch
1000Base-LX ports.
Light Emitting Diodes (LEDs) provide status information for the
module. There are three LEDs per port (link, transmit and receive)
and one global LED (status).
The table describes the LEDs for the module.
LED
Color
Definition
Status (Board)
Solid Yellow
Power up diagnostics
are running.
Flashing Yellow
Flashing Green
Power up diagnostics
failed.
Normal Operation -
the board is operating
normally.
13
C H A P T E R 2
Intel® NetStructure™ 6000 Switch Modules User Guide
LED
Color
Definition
Link
Solid Green
The Link LED is
available on each
port. The Link LED
stays on while a good
link is available.
RX (Receive)
TX (Transmit)
Flashing Green
Flashing Green
The Receive LED is
available on each
port. It flashes on and
off as frames are
received.
The Transmit LED
flashes on and off as
frame transmissions
start and stop.
Gigabit Ethernet Troubleshooting
Power-up Problems
The following table is a quick guide to power-up problems, their
possible cause, and a suggested course of action.
Symptom
Possible Cause
Course of Action
No LEDs lit on
Gigabit Ethernet
module.
Module needs repair. Replace module.
Status LED yellow.
Start-of-day
Contact Customer
diagnostics failed for Support.
the Gigabit Ethernet
module.
14
C H A P T E R 2
Gigabit Ethernet Modules
Symptom
Possible Cause
Course of Action
Link LED is not lit.
Dirty optics.
Try different ports
and reverse the cable
(if possible). Replace
the cable. If replacing
the cable fails to help,
clean the optics.
Bad cable or incorrect
cable adapter
orientation.
Auto-negotiation
Change auto-
mode does not agree negotiation mode for
with remote link
partner.
either link partner so
that they agree.
Active Link, cannot
communicate with
other stations from
the user console.
Management
interface not IP
configured.
Use ifconfig
command, BOOTP
or RARP to
configure sw1
interface.
Active Link, cannot
communicate with
station on a non-
Invalid VLAN
configuration.
Verify the VLAN
configuration.
Gigabit Ethernet port
from a station on a
Gigabit Ethernet port.
15
Fast Ethernet
Modules
Topic
See Page
Overview of the Fast Ethernet Modules
10/100 Ethernet Module
16
16
C H A P T E R 3
Intel® NetStructure™ 6000 Switch Modules User Guide
Overview of the Fast Ethernet
Modules
The Intel® NetStructure™ 6000 switch has two Fast Ethernet
modules. One is a 100Base-TX card which can upgrade your Ethernet
network to Fast Ethernet by supporting both 10Mbps and 100Mbps
on each switched port.
The other module is a 100Base-FX card which can directly upgrade
your Ethernet network to 100Mbps.
10/100 Ethernet Module
This module is a 24-port 100Base-TX Ethernet card. It supports full-
and half-duplex 10 and 100Mbps data transfer and auto-negotiation.
Setting Auto-negotiation
Auto-negotiation allows each end of a link to query the other to
determine a compatible mode of operation. For example, if both links
support full-duplex operation, then the switch can determine this
mode.
When a link becomes active, the switch determines the highest
throughput mode of operation between the two devices.
The Control Process (CP) software also includes commands that
allow the speed and duplex of the ports to be manually set.
Note The default setting is “autoneg 100 10 full half.” The link
uses autonegotiation to choose the best mode. This is usu-
ally the best setting unless the remote partner is not working
properly. When the remote partner is not capable of autone-
gotiation, the port autosenses the speed and defaults to half
duplex.
Type the privileged set link port_number options command, where
port_number is one of the global ports on the chassis and options are
autoneg or noautoneg, 10, 100, half or full.
Example
Intel Switch>#>set link 6 100 FULL no autoneg
16
C H A P T E R 3
Fast Ethernet Modules
The link configuration is stored in non-volatile memory. This allows
the current setting to be restored upon the next reset.
The set link port_number defaults command restores the factory
default link settings to the switch.
Type the non-privileged show link port_number command to display
the current state of the link.
10/100 Ethernet Configuration
100Mbps LEDs
Link LEDs
Activity LEDs
Status LED
The module uses 24 RJ-45 modular receptacles for 100Base-TX
switched Fast Ethernet transmissions over Category 5 UTP.
According to IEEE 802.3, the cable length must not exceed 100
meters (328.1 feet).
Light Emitting Diodes (LEDs) provide status information for the
module and individual port connections.
LED
COLOR
DEFINITION
Status
Solid Yellow
Flashing Yellow
Flashing Green
Power up diagnostics are running.
Power up diagnostics failed.
Normal Operation - the board is
up and running.
Link
Solid Green
The Link LED is available on
each port. The Link LED stays on
while a good link is operable.
100Mbps
Activity
Solid Green
100Mbps channel connection is
active.
Flashing Green
The port is receiving and sending
traffic.
17
C H A P T E R 3
Intel® NetStructure™ 6000 Switch Modules User Guide
10/100 Ethernet Troubleshooting
Power-up Problems
The following table is a quick guide to power-up problems, their
possible cause, and a suggested course of action.
Possible
Symptom
Cause
Course of Action
No Link LED after Bad or improper Check cable. 100Mbps
plugging in a cable. cable type.
link requires Category 5
cable. Hub-to-switch or
switch-to-switch
connection must be made
with a “crossover” cable.
Check patch cables
especially. Never use
“silver satin” telephone
patch cables. The total
length of the cable should
be less than 100 meters
(328.1 feet) including
patches.
Ports are
configured
improperly.
The switch’s default link
connects with any
properly operating link.
However, a port can be
configured to link without
auto-negotiation into one
of several configurations.
If plugged into a port that
has been configured
differently, the link might
not connect or might not
work properly. For
example, a full-duplex
port connected to a half-
duplex port might have
many frame errors.The
best solution is to use the
ports in auto-negotiation
mode with properly
functioning devices
plugged into them.
18
C H A P T E R 3
Fast Ethernet Modules
Possible
Cause
Symptom
Course of Action
No connectivity
with a station on a
switch port.
No link. Link on See “No Link LED”
10/100 module is symptom above.
off.
Test for connectivity with
the ping command.
Cable has just Use the clear fdb
been moved from command or wait until the
one port to
another.
aging time has expired if
the destination is not
generating traffic. The set
agingtime command
establishes the aging time.
Spanning Tree
has just been
enabled.
Wait 60 seconds for state
to change to “forwarding.”
Poor performance
on a link.
A considerable
amount of Data
Link errors such
as CRC errors.
Use the show counters
command to display them.
Or, use any SNMP-based
network management tool
to generate reports based
on these counters.
Too many
collisions.
Too many stations on the
segment. Try moving
some to their own
segment.
Late Collisions.
Cables are too long. Use a
shorter cable, or add a
repeater or bridge.
There are too many
“hops.” Use fewer devices
from end to end.
19
|