653.1cs, 1.1cs
I N ST R U C T I O N S
KAPPASERIES
®
Thank you
for purchasing an Infinity Kappa Series 3-Way
Component System. We’ve organized this manual to make your installation
as simple and trouble-free as possible. Please read it thoroughly before
proceeding. Remember to keep your sales receipt with this manual in a
safe place so both are available for future reference.
MIDRANGE INSTALLATION
TWEETER INSTALLATION
Bi-Amp
RIGHT
+
GRN
–
–
GRN/WHT
Amplifier
To Woofer Amplifier
RIGHT
GRN/BLK
+
(Tweeter & Mids)
–
GRN
+
❶
sacle = 70%
–
+
LEFT
RED
RED
Connect Pigtail
Jumpers As Shown
+
–
–
+
BLK
BLK
+
–
+
–
+
–
+
–
+
–
+
–
W O O F E R
M I D R A N G E
E M I T T W E E T E R
E M I T T W E E T E
M
R I D R A N G E
W O O F E R
RIGHT
F R O M L E F T A M P L I F I E R S
F R O M R I G H T A M P L I F I E R S
+
–
❶
Amplifier
(Woofers)
BLU/BLK
–
BLU/WHT
–
–
+
To LEFT
Woofer
+HI
To RIGHT
Woofer
LEFT
REFERENCE STANDARD AUTOMOTIVE
Component System Crossover Network
HI +
TO LEFT
TO LEFT
TO RIGHT
TO RIGHT
BLU
BLU
Figure 5. Installing a Kappa 1.1cs/653.1cs midrange driver
in a door panel.
MIDRANGE
TWEETER
TWEETER
MIDRANGE
+
+
+
+
–
LO
HI
–
LO MID HI
HI MID LO
–
HI
LO
–
GRY/ RED/
RED/ GRY/
BLK
BLK
WHT
WHT
Figure 6. After installing the surface-mount plate, slide the
Kappa1.1cs EMIT-N™ tweeter down on the plate to lock in
place.
GRY
+HI
RED
RED
GRY
–
+HI
–
To LEFT
To RIGHT
Figure 2.This application shows
connections for a Kappa1cs sys-
tem and two stereo amplifiers.
WOOFER INSTALLATION
4"Midrange
4"Midrange
–
+MID
+MID
–
Tri-Amp
To LEFT
Tweeter
To RIGHT
Tweeter
Figure 4. Installing a Kappa1.1cs/653.1cs woofer
above a deck or (with the enclosed spacer) below
a deck.
NOTE: Use the mounting clips as nuts to secure
the below-deck installation.
RIGHT
+
GRN
–
GRN/WHT
Amplifier
(Tweeters)
To Midrange Amplifier
RIGHT
❶
GRN/BLK
–
GRN
+
LEFT
To Woofer Amplifier
RIGHT
❷
–
–
+
+
+
–
+
–
+
–
+
–
+
–
+
–
W O O F E R
M I D R A N G E
E M I T T W E E T E R
E M I T T W E E T E
M
R I D R A N G E
W O O F E R
Remove Pigtail
F R O M L E F T A M P L I F I E R S
F R O M R I G H T A M P L I F I E R S
RIGHT
+
–
❶
BLU/WHT
Amplifier
(Midrange)
BLU/BLK
–
–
–
To LEFT
Woofer
To RIGHT
Woofer
+
REFERENCE STANDARD AUTOMOTIVE
LEFT
Component System Crossover Network
+HI
BLU
HI +
TO LEFT
TO LEFT
TO RIGHT
TO RIGHT
BLU
MIDRANGE
TWEETER
TWEETER
MIDRANGE
+
+
+
+
–
LO
HI
–
LO MID HI
HI MID LO
–
HI
LO
–
GRY/ RED/
RED/ GRY/
BLK
BLK
WHT
WHT
RIGHT
GRY
+HI
RED
RED
GRY
+
–
–
+HI
–
Figure 7. After sliding down the flush-mount clip onto the
back of the Kappa1.1cs EMIT-N tweeter, use the supplied
hardware to fasten the cup to the panel.
❷
Amplifier
(Woofers)
To LEFT
To RIGHT
4"Midrange
4"Midrange
–
Figure 3.This application shows
connections for a Kappa1cs sys-
tem and three stereo amplifiers.
+
–
+MID
+MID
–
LEFT
To LEFT
Tweeter
To RIGHT
Tweeter
- 3 -
A NOTE ON POWER HANDLING
ADJUSTING THE SOUND
SPECIFICATIONS
The speakers used in Kappa Series 3-Way
1.1cs
Type:
After you have connected all the speakers to the
crossover according to the connection diagram,
you may adjust the overall sound of the system to
suit your taste.
The output of the woofers may be decreased by
moving the woofer + connection at the crossover
to the low position.
The output of the midrange may be decreased by
moving the midrange + connection at the
crossover to the low position.
The output of the tweeter may be increased by
moving the tweeter + connection at the crossover
to the high position or decreased by moving it to
the low position.
653.1cs
Type:
Component Systems are designed to produce rea-
sonable volume levels with little amplifier power.
However, the addition of an amplifier to drive
your speakers and a subwoofer will enhance the
dynamic range of your system, and help over-
come the ambient noise in a moving vehicle.
Kappa speakers are designed to handle the power
of a dedicated amplifier driven at or below its
rated power. If an amplifier is driven far above its
rated power, the output signal will “clip,” and the
additional power present in a clipped signal can
damage any speaker. Distorted or “fuzzy” sound
from your speakers is an indication that the ampli-
fier has exceeded its rated power, and you should
reduce the volume level
6" x 9" 3-Way System
4 ohms
200 watts per channel
6-1/2" 3-Way System
4 ohms
120 watts per channel
Speaker Impedance:
Power Handling:
Frequency
Response (±3dB):
Sensitivity:
Speaker Impedance:
Power Handling:
Frequency
Response (±3dB):
Sensitivity:
36Hz ~ 45kHz
89Hz @ 2.83 V, 1 watt
50Hz ~ 45kHz
89Hz @ 2.83 V, 1 watt
Crossover Frequencies: Woofer
Hi terminal: 210Hz
Crossover Frequencies: Woofer
Hi terminal: 210Hz
Lo terminal: 130Hz
Midrange: 400Hz
Tweeter:12.5kHz
Lo terminal: 130Hz
Midrange: 400Hz
Tweeter: 12.5kHz
Mounting Depth
Drop-in Woofer:
Cut-out
Mounting Depth,
Drop-in Woofer:
Cut-out
Diameter Woofer:
Mounting Depth,
Drop-in Midrange:
Cut-out
Diameter Midrange: 3-3/4" (96 mm)
Mounting
DepthTweeter:
Cut-out
DiameterTweeter:
2-9/16" (65 mm)
2-1/2" (67.5 mm)
5-11/16" (149 mm)
1-13/16" (46 mm)
Diameter Woofer:
5-11/16" x 8-3/4"
(149 mm x 223 mm)
Mounting Depth,
Drop-in Midrange:
Cut-out
Diameter Midrange: 3-3/4" (96 mm)
Mounting
DepthTweeter:
Cut-out
DiameterTweeter:
1-13/16" (46 mm)
GENERAL CARE
The loudspeaker grilles may be cleaned with a
slightly damp cloth. Do not use any cleaners or
solvents on the grilles or the speaker cones.
1" (25.4 mm)
1" (25.4 mm)
3-3/8" x 1-3/4"
(84.6 mm x 44.7 mm)
3-3/8" x 1-3/4"
(84.6 mm x 44.7 mm)
DECLARATION OF CONFORMITY
We, Infinity Systems A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards:
EN 50 081-1/1992
Steen Michaelsen
Infinity Systems A/S
EN 50 082-1/3.1995
Birkerød. DENMARK. 2/98
Infinity Systems, Inc. • 250 Crossways Park Drive,
Woodbury, NY 11797 USA • (516) 496-3400 • FAX (516) 682-3583
®
|