TOTAL SPEAKER SOLUTIONS
TSS-SAT500
Owner’s Guide
(230V)
INTRODUCTION
PLACEMENT
InfinityTotal Solutions™
NOTE: The TSS-SAT500 can be placed directly on a shelf,
or mounted on a wall using the included wall bracket.
Infinity Total Solutions continues Infinity’s longstanding commitment
to accurate sound reproduction. Our high-quality drivers, precision
dividing networks and rigid, well-braced enclosures combine to
deliver uncompromised performance in any multichannel home
theater system. In addition, the TSS-SAT500 is magnetically
shielded for safe place-ment adjacent to a television.
As Left and Right Front Channels
For left and right front channels, place one satellite to the left and
another to the right of the television, as shown in Figure 1.
Since the speakers are magnetically shielded, you can place them
very close to the TV without worrying about the magnetic field
distorting the picture.
INCLUDED
As Surround Channels
For left and right surround channels, place one speaker on the left
and another on the right, to the side of or slightly behind the
listening area.The surround speakers should be mounted at a
height of between 5 ft. (1.5m) and 7 ft. (2m).
In 6- or 7-channel configurations, place the rear channel(s) behind
the listening position, as shown in Figures 1 and 2.
®
NOTE: An Infinity powered subwoofer will add impact and realism to
both music and film soundtracks. Contact your Infinity dealer for
recommendations on subwoofer models for your application.
(1) Speaker
(1) Wall bracket
PLANNING YOUR SYSTEM
Before deciding where to best place your speakers, survey your
room and study Figures 1 and 2.
Mounting on Floor Stands
An optional TSS-STAND500 floor stand is available, should you
prefer to place your TSS-SAT500 satellites on the floor; see your
In addition, there is a 1/4"-20 insert in each satellite that allows
the satellite to be mounted to many third-party floor stands. Unscrew
the rear foot to reveal the insert.
Subwoofer
Left
Front
Channel
Right
Front
Channel
Center
Channel
Couch
Left
Surround
Channel
Right
Surround
Channel
Center Rear Channel
Figure 1.This overhead view shows a typical home theater plan.
Left/right rear channels are for a 7-channel system. Center rear
channel is for a 6-channel system.
r
Rear
Cente
Channel
Figure 2.This figure shows an alternate layout, which may be
more suitable for some rooms. Left/right rear channels are
for a 7-channel system. Center rear channel is for a 6-channel
system.
3
TSS-SAT500
Step 5. Screw the ball and shaft assembly (B) to 1/4"-20 insert on
rear of speaker. Back out 1/2 of a turn and tighten nut against the
speaker.
WALL-MOUNTING
The TSS-SAT500 satellite is designed to be mounted on the wall.
There is a wall bracket included.The speaker bracket will require
four 1-1/2" #10 wood screws; each screw should be fastened to a
wall stud. If a wall stud is unavailable, install an anchor appropriate
for a 1-1/2"#10 screw.
NOTE: The customer is responsible for the correct selection and use
of mounting hardware (available through hardware stores) that will
ensure the proper and safe wall-mounting of the speakers.
Step 1. Detach shelf stand by removing screw in rear of speaker.
Step 6.Attach speaker wire as shown on page 5.
Step 7. Drop round collar (C) over ball and shaft assembly (B) that
is mounted to the speaker with the finished side of the collar facing
the rear of the speaker.
Step 8. Carefully push the ball straight into the socket mounted on
the wall, angle the speaker as desired and tighten the collar using
the enclosed metal bar.
Step 2. Mark the positions on the wall where you would like to place
the mounting screws.
Step 3. Place bracket against the wall and fasten four 1-1/2" #10
wood screws through the bracket’s screw holes into the wall. If a
wall stud is not available, use an appropriate anchor.
Metal Bar
Step 4. Unscrew round collar (C) from bracket (A).
®
A
Figure 3. Bracket on wall.
C
B
4
TSS-SAT500
CONNECTIONS
MAINTENANCE AND SERVICE
After placing the speakers, you are ready to connect your system.
First, turn off all audio-system power. Use high-quality speaker wire
to make your connections. #18-gauge speaker wire with polarity
coding is included. For longer distances, #16-gauge or heavier
wire is recommended.The side of the wire with a ridge or other
coding is usually considered positive polarity (i.e., +). Also, consult
the owner’s manuals that were included with your amplifier or
receiver to confirm connection procedures.
The TSS-SAT500 enclosure may be cleaned using a soft cloth to
remove fingerprints or to wipe off dust.
All wiring connections should be inspected and cleaned or remade
periodically.The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions and other
factors, but once per year is the minimum.
If a problem occurs, make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse the
connection wires to the left and right system. If the problem remains
in the same speaker, then the fault is with the loud-speaker. If the
problem appears in the opposite speaker, the cause is in another
component or cable. In the event that your TSS-SAT500 ever needs
service, contact your local Infinity dealer or distributor, or visit
Observe polarities when making speaker connections, as shown in
Figure 4. Connect each + terminal on the back of the amplifier or
receiver to the respective + (red) terminal on each speaker.
Connect the – (black) terminals in the same way.
Important!
Do not reverse polarities (i.e., + to –, or – to +) when making
connections. Doing so will cause poor imaging and diminished bass
response. Be certain that positive and negative wire strands are
completely isolated to avoid short circuits that may damage your
equipment.
Insert Bare
End; Release
Connector
Press
Connector
In and
Hold
–
+
Figure 4. Wiring diagram shows polarity connections for one
channel of a home theater system.
TSS-SAT500
5
SPECIFICATIONS
TSS-SAT500
Frequency Range:
150Hz – 25,000Hz ( 3dB)
Recommended
Amplifier Power Range:
10 – 100 watts
86dB
Sensitivity:
(2.83V @ 1 meter)
Nominal Impedance:
Crossover Frequency:
Midrange Driver(s):
8Ω
7,000Hz
64mm (2-1/2")
magnetically shielded
High-Frequency Driver:
Dimensions (H x W x D):
Weight:
19mm (3/4")
magnetically shielded
195mm x 89mm x 70mm
(7-11/16" x 3-1/2" x 2-3/4")
0.5kg (1.2 lb)
Infinity continually strives to update and improve existing products, as well as create new ones.
The specifications and construction details in this and related Infinity publications are
therefore subject to change without notice.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the products described
in this owner’s manual are in compliance with technical
standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Château du Loir, France 11/05
6
TSS-SAT500
NOTES
7
TSS-SAT500
© 2005 Harman International Industries, Incorporated.All rights reserved.
Infinity and Harman International are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.
Total Solutions is a trademark of Harman International Industries, Incorporated.
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
Part No. 406-000-05350-E 11/05
|